Azo-dye derived oxidized-nitrogen rich carbon sheets with high adsorption capability for dye effluent under both batch and continuous conditions

The simultaneous removal of methylene blue (MB) and Ca2+ by recyclable adsorbents based the scales derived from coal gasification system

The transformation of solid wastes from industrial production into effective adsorbents could significantly contribute to wastewater treatment. In this study, after acidizing and burning soft scale (SS) from coal gasification system, two magnetic adsorbents (mag-ASS and mag-BASS) were prepared via the combination of magnetite with ultrasonic, respectively. The treatment effects of mag-ASS and mag-BASS were then investigated for simulated wastewater containing macromolecular organic matter [i.e., methylene blue (MB)] and Ca2+. The results indicated that the pseudo second order kinetic, Elovich, Freundlich, Langmuir and Temkin model could well describe the adsorption behavior of MB and Ca2+ onto mag-ASS and mag-BASS. The maximum adsorption capacities of mag-ASS for MB and mag-BASS for Ca2+ were 600.53 mg/g and 102.54 mg/g, respectively. Surprisingly, the adsorption abilities of mag-ASS for MB and mag-BASS for Ca2+ show significantly higher than the others. The adsorption mechanisms of MB mainly included electrostatic interaction, π-π conjugate interaction and cation exchange, while those of Ca2+ were mainly electrostatic interaction and cation exchange. The diffusion of MB and Ca2+ onto the magnetic adsorbents might be controlled by the combined effects of intraparticle and liquid film diffusion. There was no significant reduction in adsorption capacity after 8 cycles of adsorption and desorption, indicating that SS-based magnetic adsorbents had good recyclability and stability. Moreover, the removal efficiency of mag-BASS for total hardness and total organic carbon in real coal gasification gray water (CGGW) was 82.60 and 64.10%, respectively. The treatment of CGGW and the resource of wastes would significantly promote the reasonable disposal of coal gasification scales.

Dielectric-Enhanced, High-Sensitivity, Wide-Bandwidth, and Moisture-Resistant Noncontact Triboelectric Sensor for Vibration Signal Acquisition

Noncontact triboelectric sensors (TESs) have the potential to enhance self-powered sensing performance by eliminating the need for physical contact. This study demonstrates a strategy to construct noncontact TES that enables self-powered sensing and vibration signal acquisition with high sensitivity and wide bandwidth. The incorporation of carbon nanotubes into nitrocellulose (CNTs/NC) endows the tribopositive layer with larger inner micro/nanocapacitances, consequently augmenting the charge storage capacity. As a result, the contactless sensing performance of CNTs/NC-based TES (CNTs/NC-TES) was enhanced by 146%. Correspondingly, the related theory and working mechanism of noncontact sensing were demonstrated. Furthermore, the CNTs/NC-TES exhibits optimal distance response sensitivity of 57.10 V mm-1, a wide-bandwidth response from 0.1 to 4000 Hz, and relative humidity (RH) stability. This contactless CNTs/NC-TES has the potential for high sensitivity and wide frequency vibration monitoring in a high-RH environment.

Review on Moringa oleifera, a green adsorbent for contaminants removal: characterization, prediction, modelling and optimization using Response Surface Methodology (RSM) and Artificial Neural Network (ANN)

Moringa oleifera utilization in water treatment to eliminate emerging pollutants such as heavy metal ions, pesticides, pharmaceuticals, and pigments has been extensively evaluated. The efficacy of Moringa oleifera biosorbent has been investigated in diverse research work using various techniques, including its adsorption capacity kinetic, thermodynamic evaluation, adsorbent modifications, and mechanism behind the adsorption process. The Langmuir isotherm provided the most remarkable experimental data fit for batch adsorption investigations, whereas the best fit was obtained with the pseudo-second order kinetic model. Furthermore, only a few papers that combined batch adsorption with fixed-bed column investigations were examined. In the latter articles, the scientists modified the adsorbent to increase the material's adsorption capacity as determined by analytical methods, including IR spectroscopy, scanning electronic microscope (SEM), and X-ray diffraction (XRD). However, the raw material can show appreciable adsorption capacity values, proving moringa's potency as a biosorbent. Hydrogen bonds, electrostatic interaction, and van der Waals forces were the main processes in the found and reported adsorbent-adsorbate interactions. These mechanisms could change depending on the physiochemical nature of adsorption. Although frequently employed for heavy metal ions and dye adsorption, Moringa oleifera can still be explored in pesticide and medication adsorption investigations due to the few publications in this comprehensive review. This study, therefore, examined different Adsorbents from the Moringa oleifera plant, as well as parameters and models for enhancing the adsorption process.

Laser-cum-KOH activation allows interfacial engineering of cardboard-derived carbon, tunable ionic states, and universal dye adsorption

In this study, we demonstrate the preparation of laser-cum KOH-activated porous carbon with tunable ionic states, unique surface chemistry, and physical texture from renewable and environmentally friendly precursors (waste cardboard boxes). The adsorption performance of the engineered adsorbents is examined on the adsorption of methyl blue (MB, anionic) and methylene blue (MeB, cationic). The adsorption mechanism was determined using detailed batch adsorption, and the MB was adsorbed via the formation of ternary complexes, whereas the MeB was adsorbed through cation-π interaction. Furthermore, the non-activated laser-induced carbon (LIC100) and the KOH-activated carbon (KAC(L)) exhibit superior dye adsorption capacities of 9610 (MB) and 1882 mg g-1 (MeB), respectively. To the best of our knowledge, this is the highest ever reported at dye removal in the field of adsorptive dye removal. Langmuir isotherm model and pseudo-second-order are fitted well for both MB and MeB adsorption. Lastly, the carbons generated through this modern technique can be remodeled into a more secure device to obtain clean and microorganism-free water. This study showed the potential of laser-induced carbonization of KOH-activated substrate and provided unique insights into future development for universal dye adsorption and other possible applications.

Modification of the electronic structure of g-C3N4 using urea to enhance the visible light-assisted degradation of organic pollutants

Graphitic carbon nitride has been proven to be a good candidate for using solar energy for photo-induced pollutant degradation. However, the high photo-induced holes-electron recombination rate, unfavorable morphology, and textural properties limited their application. In this study, we present a novel g-C3N4 with a novel electronic structure and physiochemical properties by introducing a single nitrogen in the graphitic network of the g-C3N4 through a novel method involving step-by-step co-polycondensation of melamine and urea. Through extensive characterization using techniques such as XPS, UPS-XPS, Raman, XRD, FE-SEM, TEM, and N2 adsorption-desorption, we analyze the electronic and crystallographic properties, as well as the morphology and textural features of the newly prepared g-C3N4 (N-g-C3N4). This material exhibits a lower C/N ratio of 0.62 compared to conventional g-C3N4 and a reduced band gap of 2.63 eV. The newly prepared g-C3N4 demonstrates a distinct valance band maxima that enhances its photo-induced oxidation potential, improving photocatalytic activity in degrading various organic pollutants. We thoroughly investigate the photocatalytic degradation performance of N-g-C3N4 for Congo red (CR) and sulfamethoxazole (SMX), and removal of up to 90 and 86% was attained after 2 h at solution pH of 5.5 for CR and SMX. The influence of different parameters was examined to understand the degradation mechanism and the influence of reactive oxygenated species. The catalytic performance is also evaluated in the degradation of various organic pollutants, and it showed a good performance.

Electronic structure modulation of multi-walled carbon nanotubes using azo dye for inducing non-radical reaction: Effect of graphitic nitrogen and structural defect

Multiwalled carbon nanotube (MWCNT) have a great potential for advanced oxidation process as a metal free catalyst. However, there catalytic activity is very low and needs to be appropriately tuned. Herein, we demonstrate a novel synthesis method for tuning the defect and surface functionality of MWCNT using azo dyes and the catalytic performance was tested for the degradation of different organic contaminates using PMS as an oxidant. The content, type of heteroatom functional groups, and the defect parameters were optimized by varying the pH and concentration of the organic dye. The quenching effect showed that singlet oxygen (¹O₂) is the primary reactive species generated by graphitic nitrogen, which can be boosted by the degree of graphitic structure disruption in MWCNT. The Linear sweep voltammetry (LSV) also confirmed that extrinsic doping enhanced the non-radical degradation by increasing the direct charge transfer rate from MB to PMS. Moreover, the designed catalyst showed a fast degradation performance with 35.1 kJ/mol activation energy and achieved the highest dye degradation rate and even surpassed some state-of-the-art metal-based and metal-free catalysts. The effect of inorganic anions study has also confirmed its industrial applicability.

Ground coffee waste-derived carbon for adsorptive removal of caffeine: Effect of surface chemistry and porous structure

Carbon-based adsorbents show high adsorption capacity towards caffeine due to their porosity and surface functionality. However, the main limiting factor for high performance has not been addressed; furthermore, the adsorption interaction with different active sites needs to be explored. In this study, we synthesized a hierarchical porous nitrogen-doped carbon with unique surface functionality by single-step calcination of coffee waste with KOH under N₂. The porous structure, nitrogen content, and types are optimized by varying calcination temperature and KOH concentration. The result of the adsorption experiments shows that both the nitrogen type and the pore size distribution are the limiting factors to adsorption. In addition, the effect of acidic and basic functional groups is studied in detail. The adsorption of caffeine on CW-C is dominantly governed by EDA interaction between the resonance structure of pyridonic-N and the electron-withdrawing group of the caffeine, and the dispersive force caused by the oxidized-N and delocalized π electron of caffeine. Furthermore, we demonstrate that the surface of CW-C is not suitable for the formation of electrostatic and non-electrostatic interaction with caffeine. The maximum adsorption capacity of caffeine at 25 °C is 274.2 mg/g. Moreover, we demonstrate that the unique physio-chemical properties of CW-C are capable of adsorbing other emerging contaminants such as diclofenac, where maximum adsorption capacity of 242.3 mg/g diclofenac is recorded.

Continuous fixed-bed column study and adsorption modeling removal of Ni2+, Cu2+, Zn2+ and Cd2+ ions from synthetic acid mine drainage by nanocomposite cellulose hydrogel

Heavy metal ions are widely recognized for their harmful effects on human health and the environment. Heavy metal ions removal using nanocomposite hydrogel is a promising method for industrial applications and process development owing to their utilization in both kinematic and dynamic adsorption process. There is a need to develop simple, low-cost water purification techniques that use biodegradable bio-based natural polymers like cellulose nanocrystal that have been modified with nanomaterials. These innovative functional cellulose nanocrystals-based nanomaterials have been shown to successfully remove a variety of contaminants from wastewater to acceptable levels. Due to their capacity to hold water in their porous structures, hydrogels are the most commonly used 3D polymer mesh materials for environmental remediation. The application of potential hydrogel for the absorption of Cu²⁺, Ni²⁺, Zn²⁺ and Cd²⁺ ions from an aqueous solution in a packed bed adsorption column was studied in this work. The adsorbent was studied using FTIR, SEM, XRD and TGA. The influence of breakthrough factors such as bed height (10, 17 and 25 cm) influent concentration (10, 20 and 50 mg/L) and the feed flow rate (10, 20 and 30 mL/min) was assessed. Bed Depth Service Time, Thomas and Yoon-Nelson models were used to fit the experimental data. With an increase in bed height, breakthrough and exhaustion time, the removal efficiency rose to 99.42 ± 0.12 for Cu²⁺, 99.23 ± 1.16 for Ni²⁺, 99.36 ± 0.89 for Cd²⁺ and 98.94 ± 0.48 for Zn²⁺, but declined with increased flow rate and influent concentration. Better performance was observed at a bed height of 25 cm, an influent metal ion concentration of 10 mg/L and a flow velocity of 10 mL/min. The BDST and Yoon-Nelson models were both successfully used to predict the breakthrough curves of heavy metal ions removal.

Methylcellulose/tannic acid complex particles coated on alginate hydrogel scaffold via Pickering for removal of methylene blue from aqueous and quinoline from non-aqueous media

Adsorbents reported for liquid phase decontamination under both aqueous and non-aqueous media are all dispersed phase sorbents that further require a tedious separation step post adsorption. Herein, a monolith, highly porous, and mechanically robust scaffold was synthesized for the adsorption of pollutants from both aqueous and non-aqueous media with facile separation and regeneration. Methylcellulose-tannic acid complex particles were prepared and systematically decorated on the surface of interpenetrating polymer network (IPN) scaffold via Pickering emulsion. Due to the surface coating of the particles, plausible amphiphilic adsorption of quinoline (QUI) and methylene blue (MB) was achieved from fuel and water, respectively. The hydroxyl (OH-) and carboxyl (COOH-) groups of tannic acid, alginate, and polyacrylic acid created hydrogen bonding, electrostatic interaction, acid-base interaction, and π-π stacking. Maximum adsorption capacity of 791.17 mg/g MB and 460.92 mg/g QUI was recorded with facile separation, excellent adsorbent regeneration, and reusability. Although both followed the pseudo-second-order adsorption kinetic model, a different mechanism was identified to govern the adsorption under aqueous and non-aqueous environment i.e. only the surface particles were active for QUI adsorption while the scaffold was also involved for MB adsorption.

Preparation of a double-network hydrogel based on wastepaper and its application in the treatment of wastewater containing copper(ii) and methylene blue

To reclaim and utilize wastepaper (WP), a WP/acrylamide double-network hydrogel (WP/PAM) was prepared to transform WP into efficient adsorbent for heavy metals and dye wastewater treatment. The structure and properties of the WP/PAM were characterized systematically by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), swelling performance (SR), Fourier transform infrared spectrum (FTIR), and X-ray photoelectron spectroscopy (XPS). Batch experiments showed that the adsorption process of Cu(ii) and MB followed the pseudo-second-order kinetic model and the Langmuir model. The maximum adsorption capacities of the WP/PAM for Cu(ii) and MB were 142.2 mg g⁻¹ and 1714.5 mg g⁻¹, respectively. The adsorption mechanism of Cu(ii) on the WP/PAM was related to ion exchange and complexation, while MB adsorption was driven by hydrogen bonding and electrostatic interaction. Besides, the WP/PAM performed well in treating simulated wastewater. The regeneration test indicated that the WP/PAM could be successfully reused after 6 cycles. This work provided an alternative choice for the recycling of WP and produced a potential adsorbent for the dye and heavy metals wastewater treatment.

In this research, wastepaper was innovatively compounded with acrylamide to prepare a wastepaper/acrylamide double-network hydrogel and was applied to the treatment of the mixed wastewater containing copper(ii) and methylene blue.