Removal of Congo red dyes from aqueous solutions by porous γ-alumina nanoshells

Self-supporting and hierarchical porous membrane of bacterial nanocellulose@metal-organic framework for ultra-high adsorption of Congo red

The widespread use of synthetic dyes has serious implications for both the environment and human health. Therefore, there is an urgent need for the development of novel, high-efficiency adsorbents for these dyes. In this study, a Zirconium-based metal-organic framework (MOF) with controllable morphology was in-situ grown on bacterial nanocellulose (BC) via a solvothermal method. The resulting BC@MOF composite nanofibers have a high specific surface area of 651 m2/g and can be assembled into a self-supported porous membrane (BMMCa) through vacuum filtration with the assistance of calcium ions. The addition of Ca(II) significantly enhanced the mechanical properties of the membrane through dispersion effect and electrostatic interactions, as well as enhancing its adsorption performance through the salting-out effect. The BMMCa membrane, with its hierarchical porous structure and high flux, exhibits high selectivity for Congo red (CR) with an ultra-high adsorption capacity of 3518.6 mg/g. Furthermore, the self-supporting membrane achieved rapid and convenient removal of CR through circulating filtration adsorption. The adsorption mechanism and selectivity were verified through the molecular dynamics simulation calculations by Materials Studio (MS) software. This membrane-based adsorbent, with its ultra-high adsorption capacity, good selectivity, and recycling ability, has great potential for practical wastewater treatment applications.

Condensed Layer Deposition of Nanoscopic TiO2 Overlayers on High-Surface-Area Electrocatalysts

Encapsulating an electrocatalytic material with a semipermeable, nanoscopic oxide overlayer offers a promising approach to enhancing its stability, activity, and/or selectivity compared to an unencapsulated electrocatalyst. However, applying nanoscopic oxide encapsulation layers to high-surface-area electrodes such as nanoparticle-supported porous electrodes is a challenging task. This study demonstrates that the recently developed condensed layer deposition (CLD) method can be used for depositing nanoscopic (sub-10 nm thick) titanium dioxide (TiO2) overlayers onto high-surface-area platinized carbon foam electrodes. Characterization of the overlayers by transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS) showed that the films are amorphous, while X-ray photoelectron spectroscopy confirmed that they exhibit TiO2 stoichiometry. Electrodes were also characterized by hydrogen underpotential deposition (Hupd) and carbon monoxide (CO) stripping, demonstrating that the Pt electrocatalysts remain electrochemically active after encapsulation. Additionally, copper underpotential deposition (Cuupd) measurements revealed that TiO2 overlayers are effective at blocking Cu2+ from reaching the TiO2/Pt buried interface and were used to estimate that between 43 and 98% of Pt surface sites were encapsulated. Overall, this study shows that CLD is a promising approach for depositing nanoscopic protective overlayers on high-surface-area electrodes.

Process Optimization and Equilibrium, Thermodynamic, and Kinetic Modeling of Toxic Congo Red Dye Adsorption from Aqueous Solutions Using a Copper Ferrite Nanocomposite Adsorbent

In the present investigation of copper ferrite, a CuFe2O4 nanocomposite adsorbent was synthesized using the sol-gel method, and its relevance in the adsorptive elimination of the toxic Congo red (CR) aqueous phase was examined. A variety of structural methods were used to analyze the CuFe2O4 nanocomposite; the as-synthesized nanocomposite had agglomerated clusters with a porous, irregular, rough surface that could be seen using FE-SEM, and it also contained carbon (23.47%), oxygen (44.31%), copper (10.21%), and iron (22.01%) in its elemental composition by weight. Experiments were designed to achieve the most optimized system through the utilization of a central composite design (CCD). The highest uptake of CR dye at equilibrium occurred when the initial pH value was 5.5, the adsorbate concentration was 125 mg/L, and the adsorbent dosage was 3.5 g/L. Kinetic studies were conducted, and they showed that the adsorption process followed a pseudo-second-order (PSO) model (regression coefficient, R2 = 0.9998), suggesting a chemisorption mechanism, and the overall reaction rate was governed by both the film and pore diffusion of adsorbate molecules. The process through which dye molecules were taken up onto the particle surface revealed interactions involving electrostatic forces, hydrogen bonding, and pore filling. According to isotherm studies, the equilibrium data exhibited strong agreement with the Langmuir model (R2 = 0.9989), demonstrating a maximum monolayer adsorption capacity (qmax) of 64.72 mg/g at pH 6 and 302 K. Considering the obtained negative ΔG and positive ΔHads and ΔSads values across all tested temperatures in the thermodynamic investigations, it was confirmed that the adsorption process was characterized as endothermic, spontaneous, and feasible, with an increased level of randomness. The CuFe2O4 adsorbent developed in this study is anticipated to find extensive application in effluent treatment, owing to its excellent reusability and remarkable capability to effectively remove CR in comparison to other adsorbents.

Polymeric Networks Derived from UV-Curing of Bio-Based Polyesters for Methyl Violet Removal

In this study, firstly, the syntheses and characterizations of biobased polyesters with different acid values obtained from the condensation reaction of biobased itaconic acid and polyethylene glycol were investigated. Then, UV curing was applied to form polymeric networks as adsorbent material from these polyesters containing different acids. Fourier transform infrared spectrometry (FTIR), Nuclear Magnetic Resonance Spectroscopy (NMR), X-ray Photoelectron Spectroscopy (XPS), Gel Permeation Chromatography (GPC) and scanning electron microscope (SEM) were used for the characterization of polymeric networks. The effects of the parameters of contact time, initial dye concentration, pH, temperature, amount of adsorbent on adsorption were investigated by batch method. In addition, adsorption equilibrium data were analyzed by Langmuir, Freundlich, Tempkin, Elovich, Redlich-Peterson, Harkin-Jura and Jossens adsorption models. Kinetic and thermodynamic studies were performed at 298, 308, 318 and 328 K and desorption studies were also examined. Comparison studies for the effects of the acid values of the adsorbent materials on the removal of methyl violet (MV) organic pollutant from aqueous solutions were analyzed. According to the pseudo-second-order model, the adsorption capacities were found to be ≥ 357.14 mg/g for the adsorbents. From the thermodynamic data, it was determined that the mechanism was exothermic and spontaneous. As a result of the third reuse, it was found that the adsorbents had a removal efficiency of ≥ 72.36%. According to the results observed the increase in the acidities in the chemical structure of bio-based polymeric networks enhances the adsoption properties.

Removal of anthraquinone dye from wastewaters by hybrid modified activated carbons

Dyes are among the main environmental pollutants, due to the high amount of discharge of wastewater, lost in the dyeing process, without any further treatment. Anthraquinone dyes are stable and resistant in the aquatic system. Among the methods that have been applied to remove these dyes from wastewaters, adsorption on activated carbon has been reported as a very effective technique, and its modification with oxides and hydroxides of metals have been used to increase its surface area. In the present study, the production of activated carbon was originated by coconut shells, and a mixture of metals and metalloids, such as magnesium, silicate, lanthanum, and aluminum (AC-Mg-Si-La-Al), was used for its subsequent modification and applied to Remazol Brilliant Blue R (RBBR) removal. AC-Mg-Si-La-Al surface morphology was studied by BET, FTIR, and SEM methods. For the evaluation of AC-Mg-Si-La-Al, several parameters, such as dosage, pH, contact time, and initial RBBR concentration were studied. According to the results, in pH 5.0 ± 0.1, the dye percentage rate reached 100% by applying 0.5 g/L. Therefore, the optimal dose of 0.4 g/L and pH 5.0 ± 0.1 are selected, which leads to 99% removal of RBBR. The experimental data found to better fit to Freundlich isotherm (R² = 0.9189) and pseudo-second-order kinetic (R² = 0.9291) models and 4 h were the sufficient time for adsorption. According to thermodynamics, a positive value of ∆H⁰ (19.661 kJ/mol) suggests the endothermic nature of the process. The AC-Mg-Si-La-Al adsorbent was able to regenerate after 5 cycles of use, showing only a 17% decrease in its efficiency. Because of its effectiveness in full RBBR removal, AC-Mg-Si-La-Al could be further examined for the removal of several other dyes, even anionic or cationic.

Biocompatible cellulose acetate supported ammonium based ionic liquid membranes; way forward to remediate water pollution

Dyes contaminated water has caused various environmental and health impacts in developing countries especially Pakistan due to different industrial activities. This issue has been addressed in present study by fabricating biocompatible ionic liquid (IL) membranes for the remediation of Crystal violet (CV) dye from contaminated water. Novel ammonium-based IL such as Triethyl dimethyl ammonium sulfate ([C3A][C2H6]SO4); (A2) was synthesized and further functionalized with hydroxyapatite (HAp; extracted from refused fish scales) resulting in the formation of HA2. Furthermore, A2 and HA2 were then used to fabricate the cellulose acetate (CA) based membranes with different volume ratios. The physicochemical properties of membranes-based composite materials were investigated using FTIR, XRD, and TGA and used for the adsorption of CV in the closed batch study. In results, CA-HA2 (1:2) showed higher efficiency of 98% for CV reduction, after the contact time of 90 min. Kinetic studies showed that the adsorption of CV followed the pseudo-second-order kinetic model for all adsorbents. The antibacterial properties of the synthesized membrane were investigated against gram-positive strain, S. aureus and CA-A2 (1:1) showed better antibacterial properties against S. aureus. The developed membrane is sustainable to be used for the adsorption of CV and against bacteria.

High specific surface area γ-Al2O3 nanoparticles synthesized by facile and low-cost co-precipitation method

Alumina (Al₂O₃) nanoparticles (NPs) are particularly adsorbent NPs with a high specific surface area (SSA) that may well be utilized to clean water. In this study, pure γ-alumina NPs are successfully synthesized by the co-precipitation method, and the effect of ammonium bicarbonate concentration on the synthesized NPs is studied to find the optimum concentration to provide the highest capacity of copper ions removal from water. The results declare that spherical alumina NPs with average diameters in the range of 19-23 nm are formed with different concentrations of precipitation agent, and the concentration has no significant effect on the morphology of NPs. Furthermore, the precipitating agent concentration influences the optical characteristics of the produced alumina NPs, and the bandgap energies of the samples vary between 4.24 and 5.05 eV. The most important impact of precipitating agent concentrations reflects in their SSA and capacity for copper ion removal Ultra-high SSA = 317 m²/g, and the highest copper removal at the adsorbate concentration of 184 mg/L is achieved in an alkalis solution followed by a neutral solution. However, admirable copper removal of 98.2% is even achieved in acidic solutions with 0.9 g/L of the alumina NPs synthesized at a given concentration of ammonium bicarbonate, so this sample can be a good candidate for Cu ions removal from acidic wastewater.

Utilization of metal industry solid waste as an adsorbent for adsorption of anionic and cationic dyes from aqueous solution through the batch and continuous study

Industrial waste, for instance, textile effluents when released into the ecological system without first being treated or with inappropriate levels of treatment, can lead to serious issues deteriorating the environment and human health. Moreover, solid waste from various industries has also become a major issue due to massive urbanization. For instance, the waste from the metal industry has been rapidly increasing such as Jarosite which has various metals, metal oxides, and silica in its composition. Therefore, Jarosite was utilized as an adsorbent for the adsorption of anionic Congo red (CR) and cationic Methylene blue (MB) dyes from aqueous solutions. The processed adsorbent sample was characterized by BET, XRD, SEM, EDS, FTIR, and XPS techniques. The effects of initial dye concentration, pH, adsorbent dose, temperature, and contact time were examined. The metal industry waste is used as a low-cost abundant adsorbent with great potential for adsorption ability to remove the CR (97.5%) and MB (68.5%) at pH 7, contact time 90 min, adsorbent dose 0.1 g, and initial dye concentration 50 mg/L. The adsorption data followed the adsorption isotherm and Kinetics for both dyes. The removal of both dyes was a physical adsorption process, endothermic and spontaneous reaction. Column adsorption investigation was described by AB (Adams-Bohart) and YN (Yoon-Nelson) models. According to the economic view, the utilization of jarosite for dye removal is a cost-effective approach, because it is collected free of cost from industries. Henceforth, for the first time, toxic metal industry waste was successfully utilized as an adsorbent for wastewater treatment.

Elimination of toxic azo dye using a calcium alginate beads impregnated with NiO/activated carbon: Preparation, characterization and RSM optimization

Nickel oxide nanoparticles supported activated carbon (AC-NiO) was fabricated using thermal activation. Then, AC-NiO composite was immobilized on alginate beads to obtain 3-dimensional network structure ALG@AC-NiO nanocomposite beads for catalytic reduction of Congo red (CR) dye. The resulting nanocomposite beads were identified by various physical techniques. The crystalline nature and dispersion of NiO nanoparticles was defined by the XRD and EDS techniques, respectively. ALG@AC-NiO beads have a Ni element content of 4.65 wt% with an average NiO particle diameter of 23 nm. The statistical approach mathematically describes the catalytic reduction of the CR dye as a function of the NaBH₄ concentration, the catalyst dose and the concentration of the CR dye modeled by a BBD-RSM. According to the statistical modeling and the optimization process, the catalytic optimum conditions were obtained for NaBH₄ concentration of 0.05 M, catalyst dose of 11 mg and CR dye concentration of 80 ppm who permit meet 99.67 % of CR dye conversion. The adjusted coefficient of determination (R² = 0.9957) indicates that the considered model was quite suitable with a good correlation between the experiment and predicted.

Effective and Efficient Porous CeO2 Adsorbent for Acid Orange 7 Adsorption

A porous CeO₂ was synthesized following the addition of guanidine carbonate to a Ce³⁺ aqueous solution, the subsequent addition of hydrogen peroxide and a final hydrothermal treatment. The optimal experimental parameters for the synthesis of porous CeO₂, including the amounts of guanidine carbonate and hydrogen peroxide and the hydrothermal conditions, were determined by taking the adsorption efficiency of acid orange 7 (AO7) dye as the evaluation. A template-free hydrothermal strategy could avoid the use of soft or hard templates and the subsequent tedious procedures of eliminating templates, which aligned with the goals of energy conservation and emission reduction. Moreover, both the guanidine carbonate and hydrogen peroxide used in this work were accessible and eco-friendly raw materials. The porous CeO₂ possessed rapid adsorption capacities for AO7 dye. When the initial concentration of AO7 was less than 130 mg/L, removal efficiencies greater than 90.0% were obtained, achieving a maximum value of 97.5% at [AO7] = 100 mg/L and [CeO₂] = 2.0 g/L in the first 10 min of contact. Moreover, the adsorption-desorption equilibrium between the porous CeO₂ adsorbent and the AO7 molecule was basically established within the first 30 min. The saturated adsorption amount of AO7 dye was 90.3 mg/g based on a Langmuir linear fitting of the experimental data. Moreover, the porous CeO₂ could be recycled using a NaOH aqueous solution, and the adsorption efficiency of AO7 dye still remained above 92.5% after five cycles. This study provided an alternative porous adsorbent for the purification of dye wastewater, and a template-free hydrothermal strategy was developed to enable the design of CeO₂-based catalysts or catalyst carriers.

Adsorptive removal of anionic azo dye by Al3+-modified magnetic biochar obtained from low pyrolysis temperatures of chitosan

Magnetic γ-Fe₂O₃/Al³⁺@chitosan-derived biochar (m-Fe₂O₃/Al³⁺@CB) was prepared by introducing magnetic maghemite (γ-Fe₂O₃) nanoparticles and aluminum sulfate [Al₂(SO₄)₃] into chitosan-derived biochar (CB) obtained at low pyrolysis temperatures. m-Fe₂O₃/Al³⁺@CB was used to remove typical anionic azo dye (Congo red, CR). Effects of initial CR concentration, contact time, initial pH value, background electrolytes, and temperature on CR adsorption by m-Fe₂O₃/Al³⁺@CB were studied. Compared with magnetic chitosan-derived biochar (m-Fe₂O₃@CB), m-Fe₂O₃/Al³⁺@CB exhibited excellent performance for a wider range of pH values (pH 1-7) and in the presence of background electrolyte. The introduction of Al³⁺ is an effective method for improving the properties of magnetic chitosan-derived biochar. High CR adsorption capacity (636.94 mg g^-1) of m-Fe₂O₃/Al³⁺@CB could result from collaborative effect of flocculation/coagulation and electrostatic attraction. These results demonstrated that m-Fe₂O₃/Al³⁺@CB is a potential adsorbent for effective removal of organic dyes from aqueous solution due to its high adsorption capacity and convenient magnetic recovery and stronger anti-interference ability against coexisting anions in wastewater.

Iodine adsorption isotherms on Matamba fruit shell stemmed biochar for wastewater re-use strategy in rural areas owing to climate change

Remote communities in developing countries are facing ever-increasing water scarcities, due to cumulative demand induced by the climate change and global warming impacts. For the socio-economic and health well-being of the local communities, sufficient, efficient, and affordable water supply is fundamental from local-based adsorbents. Matamba Fruit shell was obtained and pyrolyzed to obtain well-transformed biochar, which exhibited enough capacity to remove Iodine from aqueous solution. The maximum capacity of adsorption of the Matamba Fruit shell was 2.122 mmol L^-1 and 2.12 mmol L^-1 from conventional and Bayesian statistics correspondingly. The difference was insignificant. The surface morphology was evaluated by the Field Emission Scanning Electron Microscopy with Energy Dispersive X-Ray Spectroscopy (FESEM-EDX) which revealed porous structures with irregular openings enough to purge wastewater pollutants. The material surface area was 267.0 m² g^-1, as estimated by both approaches, making the Matamba Fruit shell an emerging potential candidate for environmental pollution control and use in bioremediation practices. The Fourier-transform infrared spectroscopy (FTIR) revealed that surface functional groups of Matamba Fruit shell biochar have enough peak variations in intensity and position due to vibration variations of the surface. The Fruit shell has different functional groups including the hydroxyl (-OH) and the carbonyl groups (CO), CC stretches of aromatic rings, and the carboxylate (C-O-O-) groups. The biochar understudy unveiled its capability for wastewater-treatment reuse in local and urban communities of developing countries to safeguard their health and access to water-supply as the climate change reverberations are affecting the developing countries more pronounced than before.

Chitosan-Functionalized Hydroxyapatite-Cerium Oxide Heterostructure: An Efficient Adsorbent for Dyes Removal and Antimicrobial Agent

The current research intended to employ a facile and economical process, which is also ecofriendly to transform camel waste bones into novel heterostructure for cleansing of diverse waste waters. The bones of camel were utilized for preparation of hydroxyapatite by hydrothermal method. The prepared hydroxyapatite was applied to the synthesis of cerium oxide-hydroxyapatite coated with natural polymer chitosan (CS-HAP-CeO₂) heterostructure. Being abundant natural polymer polysaccharide, chitosan possesses exceptional assets such as accessibility, economic price, hydrophilicity, biocompatibility as well as biodegradability, therefore style it as an outstanding adsorbent for removing colorant and other waste molecules form water. This heterostructure was characterized by various physicochemical processes such as XRD, SEM-EDX, TEM, and FT-IR. The CS-HAP-CeO₂ was screened for adsorption of various industrially important dyes, viz., Brilliant blue (BB), Congo red (CR), Crystal violet (CV), Methylene blue (MB), Methyl orange (MO), and Rhodamine B (RB) which are collective pollutants of industrial waste waters. The CS-HAP-CeO₂ demonstrated exceptional adsorption against CR dye. The adsorption/or removal efficiency ranges are BB (11.22%), CR (96%), CV (28.22%), MB (47.74%), MO (2.43%), and RB (58.89%) dyes. Moreover, this heterostructure showed excellent bacteriostatic potential for E. coli, that is liable for serious waterborne diseases. Interestingly, this work revealed that the incorporation of cerium oxide and chitosan into hydroxyapatite substantially strengthened antimicrobial and adsorption capabilities than those observed in virgin hydroxyapatite. Herein, we recycled the unwanted camel bones into a novel heterostructure, which assists to reduce water pollution, mainly caused by the dye industries.

Fabrication of polyamide-12/cement nanocomposite and its testing for different dyes removal from aqueous solution: characterization, adsorption, and regeneration studies

Polyamide-12/Portland cement nanocomposite was prepared by using the exfoliated adsorption method. The fabricated nanocomposite was applied first time to remove Congo red (CR), brilliant green (BG), methylene blue (MB), and methyl red (MR) from the synthetic wastewater. The polymer nanocomposite was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, elemental mapping, Brunauer-Emmett-Teller surface area analysis, and X-ray diffraction. The adsorption was rapid and all the studied dyes were absorbed on the surface of the polymer nanocomposite in 90 min. The point of zero charge was found at pH 5 and the factors such as pH, time, and temperature were found to affect the adsorption efficiency. Freundlich isotherm and pseudo-second-order models well-fitted the adsorption isotherm and kinetics data, respectively. The calculated maximum adsorption capacity was 161.63, 148.54, 200.40, and 146.41 mg/g for CR, BG, MB, and MR, respectively. The mode of the adsorption process was endothermic, spontaneous, and physical involving electrostatic attraction. On an industrial scale, the high percentage of desorption and slow decrease in the percentage of adsorption after every five regeneration cycles confirm the potential, practicality, and durability of the nanocomposite as a promising and advanced adsorbent for decolorization of colored wastewater.

Potential of nanocomposites of zero valent copper and magnetite with Eleocharis dulcis biochar for packed column and batch scale removal of Congo red dye

The current study is the first attempt to prepare nanocomposites of Eleocharis dulcis biochar (EDB) with nano zero-valent Copper (nZVCu/EDB) and magnetite nanoparticles (MNPs/EDB) for batch and column scale sequestration of Congo Red dye (CR) from synthetic and natural water. The adsorbents were characterized with advanced analytical techniques. The impact of EDB, MNPs/EDB and nZVCu/EDB dosage (1-4 g/L), pH (4-10), initial concentration of CR (20-500 mg/L), interaction time (180 min) and material type to remove CR from water was examined at ambient temperature. The CR removal followed sequence of nZVCu/EDB > MNPs/EDB > EDB (84.9-98% > 77-95% > 69.5-93%) at dosage 2 g/L when CR concentration was increased from 20 to 500 mg/L. The MNPs/EDB and nZVCu/EDB showed 10.9% and 20.1% higher CR removal than EDB. The adsorption capacity of nZVCu/EDB, MNPs/EDB and EDB was 212, 193 and 174 mg/g, respectively. Freundlich model proved more suitable for sorption experiments while pseudo 2nd order kinetic model well explained the adsorption kinetics. Fixed bed column scale results revealed excellent retention of CR (99%) even at 500 mg/L till 2 h when packed column was filled with 3.0 g nZVCu/EDB, MNPs/EDB and EDB. These results revealed that nanocomposites with biochar can be applied efficiently for the decontamination of CR contaminated water.