Biobased polyporphyrin derived porous carbon electrodes for highly efficient capacitive deionization

Electrode Materials for Desalination of Water via Capacitive Deionization

Recent years have seen the emergence of capacitive deionization (CDI) as a promising desalination technique for converting sea and wastewater into potable water, due to its energy efficiency and eco-friendly nature. However, its low salt removal capacity and parasitic reactions have limited its effectiveness. As a result, the development of porous carbon nanomaterials as electrode materials have been explored, while taking into account of material characteristics such as morphology, wettability, high conductivity, chemical robustness, cyclic stability, specific surface area, and ease of production. To tackle the parasitic reaction issue, membrane capacitive deionization (mCDI) was proposed which utilizes ion-exchange membranes coupled to the electrode. Fabrication techniques along with the experimental parameters used to evaluate the desalination performance of different materials are discussed in this review to provide an overview of improvements made for CDI and mCDI desalination purposes.

Natural phenol-inspired porous polymers for efficient removal of tetracycline: Experimental and engineering analysis

Efficient and feasible removal of trace antibiotics from wastewater is extremely important due to its environmental persistence, bioaccumulation, and toxicity, but still remains a huge challenge. Herein, three natural phenol-inspired porous organic polymers were fabricated from natural phenolic-derived monomers (p-hydroxy benzaldehyde, 2,4-dihydroxy benzaldehyde and 2,4,6-trihydroxy benzaldehyde) and melamine via polycondensation reaction. Characterization highlighted that the increasing contents of hydroxyl groups in monomers induced an increase of the polymer total porosity and promoted the formation of a highly microporous structure. With mesopore-dominated pore (average pore diameter 9.6 nm) and large pore volume (1.78 cm³/g), p-hydroxy benzaldehyde-based porous polymer (1-HBPP) exhibited ultra-high maximum adsorption capacity (q_max) of 697.6 mg/g for tetracycline (TC) antibiotic. Meanwhile, the porous networks and plentiful active sites of 1-HBPP enabled fast adsorption kinetics (within 10 min) for TC removal, which could be well described by the pseudo-second-order model. Dynamic adsorption studies showed that 1-HBPP could be used in fixed-bed adsorption column (FBAC) with high removal efficiency (breakthrough volume per unit mass, 13.2 L/g) and dynamic adsorption capacity (201.6 mg/g), which were much higher than other reported adsorbents. The breakthrough curves both well matched with Thomas and Yoon-Nelson models in FBAC treatment. Moreover, removal mechanism analysis affirmed that pore-filling, hydrogen bonding, electrostatic interactions and π-π stacking interactions were main driving forces for TC adsorption. The prepared natural phenol-inspired porous adsorbents show great potential in antibiotics removal from wastewater, and this strategy would promote the sustainable and high-value utilization of natural phenolic compounds.

In Situ Generated UiO-66/Cotton Fabric Easily Recyclable for Reactive Dye Adsorption

In view of the environmental pollution caused by the widespread use of reactive dyes in the printing and dyeing industry, the modified cotton fabric was loaded with the extremely stable metal-organic frame (MOF) material UiO-66 for removing reactive dyes from colored wastewater. UiO-66/cotton fabric was prepared by in situ synthesis, and its surface morphology and structure were analyzed by XRD, SEM, BET, and XPS. The adsorption performance of UiO-66/cotton fabric on reactive dyes was investigated by adsorbent dosage, adsorption time and temperature, dye concentration, pH, and so on. The results indicated that the adsorption equilibrium time of UiO-66/cotton fabric on reactive orange 16 was 120 min, and the removal rate was about 98%. The adsorption process belongs to simple molecular layer chemisorption and can be regarded as a spontaneous heat absorption reaction, which was consistent with the proposed secondary kinetic model and Langmuir isothermal adsorption model. In addition, the reactive dyes with a higher molecular weight of each sulfonic acid group are more hydrophobic, and the dyes are more likely to aggregate and deposit on the adsorbent surface by electrostatic attraction, hydrogen bonding, and π-π accumulation. Therefore, this work provides a potential UiO-66/cotton fabric application for the effective adsorption of reactive dyes in textile wastewater.

Potential-Mediated Recycling of Copper From Brackish Water by an Electrochemical Copper Pump

Copper ions (Cu2+ ) disposed to the environment at massive scale pose severe threat to human health and waste of resource. Electrochemical deionization (EDI) which captures ions by electrical field is a promising technique for water purification. However, the removal capacity and selectivity toward Cu2+ are unsatisfying, yet the recycling of the captured copper in EDI systems is yet to be explored. Herein, an efficient electrochemical copper pump (ECP) that can deliver Cu2+ from dilute brackish water into much more concentrated solutions is constructed using carbon nanosheets for the first time, which works based on reversible electrosorption and electrodeposition. The trade-off between the removal capacity and reversibility is mediated by the operation voltage. The ECP exhibits a removal capacity of 702.5 mg g-1 toward Cu2+ and a high selectivity coefficient of 64 for Cu2+ /Na+ in the presence of multiple cations; both are the highest reported to date. The energy consumption of 1.79 Wh g-1 is among the lowest for EDI of copper. More importantly, the Cu species captured can be released into a 20-fold higher concentrated solution. Such a high performance is attributed to the optimal potential distribution between the two electrodes that allows reversible electrodeposition and efficient electrosorption.