Performance of 2D MXene as an adsorbent for malachite green removal

Elevating electron transfer of recyclable SERS sensor using AuNPs/TiO2/Ti3C2 heterostructures for detection of malachite green in sunfish

Malachite green (MG)-contaminated aquatic products pose a serious threat to animal and human health. Hence, a novel recyclable surface-enhanced Raman scattering (SERS) substrate based on AuNPs/TiO2/Ti3C2 heterostructures was developed for the detection and degradation of MG in aquatic products. Specifically, AuNPs/TiO2/Ti3C2 heterostructures were synthesized by in situ oxidation and electrostatic adsorption based on Ti3C2 nanosheets. The excellent photocatalytic and SERS performance of the AuNPs/TiO2/Ti3C2 was demonstrated by Density functional theory (DFT) calculations and experimental results, which was attributed to the enhancement of charge transfer (CT) after the formation of heterostructures. The results demonstrate that AuNPs/TiO2/Ti3C2 is highly sensitive and recyclable. The detection limit of the sensor for MG is 8.91 × 10-5 mg/L. The sensor can be recycled for five times under the condition of light, and shows satisfactory self-cleaning performance in the food matrix, providing a possible alternative solution for the recyclable detection of MG.

Monte Carlo, molecular dynamic, and experimental studies of the removal of malachite green using g-C3N4/ZnO/Chitosan nanocomposite in the presence of a deep eutectic solvent

Deep-eutectic solvents (DES) have emerged as promising candidates for preparing nanocomposites. In this study, a DES-based graphitic carbon nitride (g-C3N4)/ZnO/Chitosan (Ch) nanocomposite was synthesized to remove malachite green (MG) dye from water. The DES was prepared by mixing and heating citric acid as a hydrogen bond acceptor and lactic acid as a hydrogen bond donor. This is the first report of the removal of MG using DES-based nanocomposites. Experiments on kinetics and isothermal adsorption were conducted to systematically explore the adsorption performances of nanocomposite toward dye. At 25 °C, the highest adsorption performance was obtained with alkaline media (>90 % removal). The greatest adsorption capacity (qm) was 59.52 mg g-1 at conditions (30 mg L-1 MG solution, pH 9, 3 mg nanocomposite per 10 mL of MG solution, 25 °C, 150 rpm, and 150 min) based on the calculation from the best-fitting isotherm model (Langmuir). The adsorption process was most appropriately kinetically described by the PSO model. The Monte Carlo (MC) and molecular dynamic (MC) results are correlated with experimental findings to validate the theoretical predictions and enhance the overall understanding of the adsorption process. Electronic structure calculations reveal the nature of interactions, including hydrogen bonding and electrostatic forces, between the nanocomposite and MG molecules.

Microalgae derived honeycomb structured mesoporous diatom biosilica for adsorption of malachite green: Process optimization and modeling

The present study investigated the removal of malachite green dye from aquifers by means of microalgae-derived mesoporous diatom biosilica. The various process variables (dye concentration, pH, and adsorbent dose) influencing the removal of the dye were optimized and their interactive effects on the removal efficiency were explored by response surface methodology. The pH of the solution (pH = 5.26) was found to be the most dominating among other tested variables. The Langmuir isotherm (R2 = 0.995) best fitted the equilibrium adsorption data with an adsorption capacity of 40.7 mg/g at 323 K and pseudo-second-order model (R2 = 0.983) best elucidated the rate of dye removal (10.6 mg/g). The underlying mechanism of adsorption was investigated by Weber-Morris and Boyd models and results revealed that the film diffusion governed the overall adsorption process. The theoretical investigations on the dye structure using DFT-based chemical reactivity descriptors indicated that malachite green cations are electrophilic, reactive and possess the ability to accept electrons, and are strongly adsorbed on the surface of diatom biosilica. Also, the Fukui function analysis proposed the favorable adsorption sites available on the adsorbent surface.

Optimization by Box-Behnken design for environmental contaminants removal using magnetic nanocomposite

In this study, a CoO-Fe2O3/SiO2/TiO2 (CIST) nanocomposite was synthesized and utilized as an adsorbent to remove methylene blue (MB), malachite green (MG), and copper (Cu) from aqueous environments. The synthesized nanocomposite was characterized using field emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and X-ray diffraction (XRD). Input parameters included pH (3-10), contact time (10-30 min), adsorbent amount (0.01-0.03 g), and pollutant concentration (20-60 mg L-1). The effects of these parameters on the removal process efficiency were modeled and optimized using the response surface methodology (RSM) based on the Box-Behnken design (BBD). The RSM-BBD method demonstrated the capability to develop a second-degree polynomial model with high validity (R2 ˃ 0.99) for the removal process. The optimization results using the RSM-BBD method revealed a removal efficiency of 98.01%, 93.06%, and 88.26% for MB, MG, and Cu, respectively, under optimal conditions. These conditions were a pH of 6, contact time of 10 min, adsorbent amount of 0.025 g, and concentration of 20 mg L-1. The synthesized adsorbent was recovered through five consecutive adsorption-desorption cycles using hydrochloric acid. The results showed an approximately 12% reduction from the first to the seventh cycle. Also, MB, MG, and Cu removal from real water samples in optimal conditions was achieved in the range of 81.69-98.18%. This study demonstrates the potential use of CIST nanocomposite as an accessible and reusable option for removing MB, MG, and Cu pollutants from aquatic environments.

Synthesis & fabrication of O-linked polymeric hybrids for recovery of textile dyes: Closed loop economy

Dyes are an important resource employed for the production systems in textile, paper, paint and leather industry. An estimate of 200,000 tons of dyes are discharged as textile effluent each year worldwide. It becomes imperative to recover these dyes by treating the effluents using economically viable routes. The present research was undertaken with the objective to attain zero emission and zero waste through development of novel polymeric hybrids as adsorbents. For this purpose, metal moieties (Al3+, Si4+, Ti4+ and Zr4+) were hybridized with polyacrylic acid, and cellulose acetate for the uptake of selected dyes under optimized parameters. The structural elucidation of four synthesized hybrids (MP-Al, MP-Si, MP-Ti and MP-Zr) by FTIR, EDX and TGA confirmed O-linked grafting of metal moieties with polymers and thermally stable porous materials. SEM micrographic images displayed void spaces providing channels for effective adsorption. The batch experiments demonstrated removal of malachite green (77-96%) and congo red (70-82%) upon contact of initial 45 min on polymeric hybrids On the other hand, pristine polyacrylic acid and cellulose acetate showed remarkably low removal of dyes. The adsorption mechanism is proposed as physical in nature following type II isotherm. Further, Langmuir and Ho's pseudo second order fitness was evaluated. In order to determine the economic viability of the present research, the real textile dyes were recovered in three consecutive cycles of adsorption and chemical treatment of hybrids. The results propose a system with positive impact on economy by maximum utilization of hybrids as adsorbents and recovery of textile dyes for reuse in textile processing.

Can MXene be the Effective Nanomaterial Family for the Membrane and Adsorption Technologies to Reach a Sustainable Green World?

Environmental pollution has intensified and accelerated due to a steady increase in the number of industries, and exploring methods to remove hazardous contaminants, which can be typically divided into inorganic and organic compounds, have become inevitable. Therefore, the development of efficacious technology for the separation processes is of paramount importance to ensure the environmental remediation. Membrane and adsorption technologies garnered attention, especially with the use of novel and high performing nanomaterials, which provide a target-specific solution. Specifically, widespread use of MXene nanomaterials in membrane and adsorption technologies has emerged due to their intriguing characteristics, combined with outstanding separation performance. In this review, we demonstrated the intrinsic properties of the MXene family for several separation applications, namely, gas separation, solvent dehydration, dye removal, separation of oil-in-water emulsions, heavy metal ion removal, removal of radionuclides, desalination, and other prominent separation applications. We highlighted the recent advancements used to tune separation potential of the MXene family such as the manipulation of surface chemistry, delamination or intercalation methods, and fabrication of composite or nanocomposite materials. Moreover, we focused on the aspects of stability, fouling, regenerability, and swelling, which deserve special attention when the MXene family is implemented in membrane and adsorption-based separation applications.

Recent Advances in the DNA-Mediated Multi-Mode Analytical Methods for Biological Samples

DNA-mediated nanotechnology has become a research hot spot in recent decades and is widely used in the field of biosensing analysis due to its distinctive properties of precise programmability, easy synthesis and high stability. Multi-mode analytical methods can provide sensitive, accurate and complementary analytical information by merging two or more detection techniques with higher analytical throughput and efficiency. Currently, the development of DNA-mediated multi-mode analytical methods by integrating DNA-mediated nanotechnology with multi-mode analytical methods has been proved to be an effective assay for greatly enhancing the selectivity, sensitivity and accuracy, as well as detection throughput, for complex biological analysis. In this paper, the recent progress in the preparation of typical DNA-mediated multi-mode probes is reviewed from the aspect of deoxyribozyme, aptamer, templated-DNA and G-quadruplex-mediated strategies. Then, the advances in DNA-mediated multi-mode analytical methods for biological samples are summarized in detail. Moreover, the corresponding current applications for biomarker analysis, bioimaging analysis and biological monitoring are introduced. Finally, a proper summary is given and future prospective trends are discussed, hopefully providing useful information to the readers in this research field.

A Competitive Study Using Electrospinning and Phase Inversion to Prepare Polymeric Membranes for Oil Removal

Polyacrylonitrile (PAN) is a popular polymer that can be made into membranes using various techniques, such as electrospinning and phase inversion. Electrospinning is a novel technique that produces nonwoven nanofiber-based membranes with highly tunable properties. In this research, electrospun PAN nanofiber membranes with various concentrations (10, 12, and 14% PAN/dimethylformamide (DMF)) were prepared and compared to PAN cast membranes prepared by the phase inversion technique. All of the prepared membranes were tested for oil removal in a cross-flow filtration system. A comparison between these membranes' surface morphology, topography, wettability, and porosity was presented and analyzed. The results showed that increasing the concentration of the PAN precursor solution increases surface roughness, hydrophilicity, and porosity and, consequently, enhances the membrane performance. However, the PAN cast membranes showed a lower water flux when the precursor solution concentration increased. In general, the electrospun PAN membranes performed better in terms of water flux and oil rejection than the cast PAN membranes. The electrospun 14% PAN/DMF membrane gave a water flux of 250 LMH and a rejection of 97% compared to the cast 14% PAN/DMF membrane, which showed a water flux of 117 LMH and 94% oil rejection. This is mainly because the nanofibrous membrane showed higher porosity, higher hydrophilicity, and higher surface roughness compared to the cast PAN membranes at the same polymer concentration. The porosity of the electrospun PAN membrane was 96%, while it was 58% for the cast 14% PAN/DMF membrane.

Application of MXene-based materials in Fenton-like systems for organic wastewater treatment: A review

Recently, Fenton-like systems have been widely explored and applied for the removal of organic matter from wastewater. Two-dimensional (2D) MXene-based materials exhibit excellent adsorption and catalysis capacity for organic pollutants removal, which has been reported widely. However, there is no summary on the application of MXene-based materials in Fenton-like systems for organic matter removal. In this review, four types of MXene-based materials were introduced, including 2D MXene, MXene/Metal complex, MXene/Metal oxide complex, and MXene/3D carbon material complex. In addition, the Fenton-like system usually consists of adsorption and degradation processes. The oxidation process might contain hydrogen peroxide (H₂O₂) or persulfate (PS) oxidants. This review summarizes the performance and mechanisms of organic pollutants adsorption and oxidants activation by MXene-based materials systematically. Finally, the existing problems and future research directions of MXene-based materials are proposed in Fenton-like wastewater treatment systems.

MXenes and MXene-supported nanocomposites: a novel materials for aqueous environmental remediation

Water contamination has become a significant issue on a global scale. Adsorption is a cost-effective way to treat water and wastewater compared to other techniques such as the Advanced Oxidation Processes (AOPs), photocatalytic degradation, membrane filtration etc. Numerous research experts are continuously developing inexpensive substances for the adsorptive removal of organic contaminants from wastewater. A fresh and intriguing area of inquiry has emerged as a result of the development of MXenes. This article aims to provide a preliminary understanding of MXenes from synthesis, structure, and characterization to the scope of further research. The applications of MXenes as a new generation adsorbent for remediation of various kinds of organic pollutants and heavy metals from wastewater are also summarized. MXenes with altered surfaces may make effective adsorbents for wastewater treatment. Lastly, the mechanism of adsorption of organic contaminants and heavy metals on MXenes is also discussed for a better understanding of the readers.

Performance of a solar photocatalysis reactor as pretreatment for wastewater via UV, UV/TiO2, and UV/H2O2 to control membrane fouling

The performance of a solar photocatalysis reactor as pretreatment for the removal of total organic carbon (TOC) and turbidity from municipal wastewater was achieved by implementing an integrated system as tertiary treatment. The process consisted of ultraviolet (UV) sunlight, UV sunlight/H₂O₂, and UV sunlight/TiO₂ nanocatalysts as pretreatment steps to prevent ultrafiltration (UF) membrane fouling. The characterization of TiO₂ was conducted with X-ray diffraction spectroscopy, Fourier-transform infrared spectroscopy, scanning electron microscopy , and Brunauer–Emmett–Teller surface area analysis. This study investigated the effect of time and solar radiation using UV, UV/H₂O₂, and UV/TiO₂ to remove TOC and turbidity. The transmembrane pressure improvement was studied using a UF membrane system to pretreat wastewater with different UV doses of sunlight for 5 h and UV/H₂O₂ and UV/TiO₂. The results showed that the highest removal efficiency of the turbidity and TOC reached 95% and 31%, respectively. The highest removal efficiency of the turbidity reached 40, 75, and 95% using UV, UV/H₂O₂, and UV/TiO₂, respectively, while the optimal removal efficiency of TOC reached 20%, 30%, and 50%, respectively.