Insight into the application of magnetic molecularly imprinted polymers in soil-washing effluent: Selective removal of 4,4'-dibromodiphenyl ether, high adaptivity of material and efficient recovery of eluent

Occurrence and ecotoxicological impacts of polybrominated diphenyl ethers (PBDEs) in electronic waste (e-waste) in Africa: Options for sustainable and eco-friendly management strategies

Polybrominated diphenyl ethers (PBDEs) are persistent contaminants used as flame retardants in electronic products. PBDEs are contaminants of concern due to leaching and recalcitrance conferred by the stable and hydrophobic bromide residues. The near absence of legislatures and conscious initiatives to tackle the challenges of PBDEs in Africa has allowed for the indiscriminate use and consequent environmental degradation. Presently, the incidence, ecotoxicity, and remediation of PBDEs in Africa are poorly elucidated. Here, we present a position on the level of contamination, ecotoxicity, and management strategies for PBDEs with regard to Africa. Our review shows that Africa is inundated with PBDEs from the proliferation of e-waste due to factors like the increasing growth in the IT sector worsened by the procurement of second-hand gadgets. An evaluation of the fate of PBDEs in the African environment reveals that the environment is adequately contaminated, although reported in only a few countries like Nigeria and Ghana. Ultrasound-assisted extraction, microwave-assisted extraction, and Soxhlet extraction coupled with specific chromatographic techniques are used in the detection and quantification of PBDEs. Enormous exposure pathways in humans were highlighted with health implications. In terms of the removal of PBDEs, we found a gap in efforts in this direction, as not much success has been reported in Africa. However, we outline eco-friendly methods used elsewhere, including microbial degradation, zerovalent iron, supercritical fluid, and reduce, reuse, recycle, and recovery methods. The need for Africa to make and implement legislatures against PBDEs holds the key to reduced effect on the continent.

Preparation and modification of polymer microspheres, application in wastewater treatment: A review

The removal of various pollutants from water is necessary due to the increasing requirements for the removal of various pollutants from wastewater and the quality of drinking water. Polymer microspheres are regarded as exemplary adsorbent materials due to their high adsorption efficiency, excellent adsorption performance, and ease of handling. Herein, the advantages and disadvantages of different preparation methods, modifications, applications and the current research status of polymer microspheres are summarized at large. Furthermore, the enhanced performance of modified composite microspheres is emphasized, including adsorption efficiency, thermal stability, and significant improvements in physical and chemical properties. Subsequently, the current applications and potential of polymeric microspheres for wastewater treatment, including the removal of inorganic and organic pollutants, heavy metal ions, and other contaminants are summarized. Finally, future research directions for polymer microspheres are proposed, outlining the challenges and solutions associated with the application of polymer microspheres in wastewater treatment.

Sorption behavior of three aromatic acids (benzoic acid, 1-naphthoic acid and 9-anthroic acid) on biochar: Cosolvent effect in different liquid phases

Influence of the cosolvent on the sorption of organic acids on biochar has not been well understood. For this purpose, the sorption (log Km, L kg-1) of three aromatic acids (benzoic acid (BA, pKa = 4.20), 1-naphthoic acid (1-NAPA, pKa = 3.70), and 9-anthroic acid (9-ANTA, pKa = 3.65) was evaluated as a function of methanol volume fraction (fc = 0.0, 0.25, and 0.5), liquid pH (2.5 and 7.0), ionic composition (CaCl2 and KCl) and ionic strength (0.005 M, 0.5 M, and 1 M CaCl2). A giant Miscanthus-derived biochar (ZPC of 2.86) was used as the sorbent. For all solutes, the sorption coefficients (log Km) measured at pH 2.5 (i.e., pH < pKa) tended to decrease with increasing fc, as expected from the cosolvency model, while the result obtained at pH 7.0 was not fully explained by the same model. The log Km of 1-NAPA in the CaCl2 system was always greater than in the KCl system (p < 0.05) and the impact became pronounced at high pH (>pKa) with increasing fc. Increasing the Ca2+ concentration at fc = 0.0 (from 0.005 M to 1 M) enhanced the value by 0.32 log unit of Km. These phenomena indicate a significant role of dissolved Ca2+ in the liquid phase, most likely due to the formation of cation bridges between aromatic carboxylates and the biochar surface (i.e., [R-COO--Ca2+]-{Biochar-}). A decrease in the dielectric constant of the methanol mixture could fortify the formation of this bridge. Regardless of the degree of cosolvency power (σ), as the number of aromatic rings of solutes increases, Km decreases in the order BA > 1-NAPA > 9-ANTA, where fc = 0.0. In conclusion, the sorption potential of biochar can be significantly weakened by increasing pH and fc, and in the absence of a divalent cation.

Computer-aided design of molecularly imprinted polymer reinforced by double hybrid monomers for selective purification of hydroxycamptothecin

A kind of hydroxycamptothecin (HCPT) hybrid molecularly imprinted polymer (AT/MA-HMIPs) with high selectivity and hard silicon skeleton was successfully prepared based on double hybrid monomers. The relationship between templates and functional monomers was studied through computer molecular simulation and experiments. Three single-monomer molecularly imprinted polymers were prepared as controls. The Langmuir isotherm and pseudo-second-order kinetic models were found to fit well with the adsorption results. The maximum adsorption capacity was 18.79 mg/g, and equilibrium was reached within 20 min. Moreover, it shows excellent selectivity (imprinting factor is 10.73) and good recoverability (after 10 adsorption-desorption cycles, the adsorption capacity only decreases by 7.75%) for HCPT. The purity of HCPT can reach 80.86% after being put into a solid phase extraction column and used in an actual sample, and the yield was 61.43%. This study lays the fundament for the development of excellent HCPT molecularly imprinted composites.