Comparison of the adsorption preference using superparamagnetic Fe3O4-SH nanoparticles to remove aqueous heavy metal contaminants

Magnetically Recyclable Wool Keratin Modified Magnetite Powders for Efficient Removal of Cu2+ Ions from Aqueous Solutions

The treatment of wastewater containing heavy metals and the utilization of wool waste are very important for the sustainable development of textile mills. In this study, the wool keratin modified magnetite (Fe3O4) powders were fabricated by using wool waste via a co-precipitation technique for removal of Cu2+ ions from aqueous solutions. The morphology, chemical compositions, crystal structure, microstructure, magnetism properties, organic content, and specific surface area of as-fabricated powders were systematically characterized by various techniques including field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), thermogravimetric (TG) analysis, and Brunauer-Emmett-Teller (BET) surface area analyzer. The effects of experimental parameters such as the volume of wool keratin hydrolysate, the dosage of powder, the initial Cu2+ ion concentration, and the pH value of solution on the adsorption capacity of Cu2+ ions by the powders were examined. The experimental results indicated that the Cu2+ ion adsorption performance of the wool keratin modified Fe3O4 powders exhibited much better than that of the chitosan modified ones with a maximum Cu2+ adsorption capacity of 27.4 mg/g under favorable conditions (0.05 g powders; 50 mL of 40 mg/L CuSO4; pH 5; temperature 293 K). The high adsorption capacity towards Cu2+ ions on the wool keratin modified Fe3O4 powders was primarily because of the strong surface complexation of -COOH and -NH2 functional groups of wool keratins with Cu2+ ions. The Cu2+ ion adsorption process on the wool keratin modified Fe3O4 powders followed the Temkin adsorption isotherm model and the intraparticle diffusion and pseudo-second-order adsorption kinetic models. After Cu2+ ion removal, the wool keratin modified Fe3O4 powders were easily separated using a magnet from aqueous solution and efficiently regenerated using 0.5 M ethylene diamine tetraacetic acid (EDTA)-H2SO4 eluting. The wool keratin modified Fe3O4 powders possessed good regenerative performance after five cycles. This study provided a feasible way to utilize waste wool textiles for preparing magnetic biomass-based adsorbents for the removal of heavy metal ions from aqueous solutions.

Synthesis of FeO@SiO2-DNA core-shell engineered nanostructures for rapid adsorption of heavy metals in aqueous solutions

Creating novel and innovative nanostructures is a challenge, aiming to discover nanomaterials with promising properties for environmental remediation. In this study, the physicochemical and adsorption properties of a heterogeneous nanostructure are evaluated for the rapid removal of heavy metal ions from aqueous solutions. Core–shell nanostructures are prepared using iron oxide cores and silica dioxide shells. The core is synthesized via the co-precipitation method and modified in situ with citric acid to grow a carboxyl layer. The shell was hydrolyzed/condensed and then functionalized with amine groups for ds-DNA condensation via electrostatic interaction. The characterization techniques revealed functional FeO@SiO₂–DNA nanostructures with good crystallinity and superparamagnetic response (31.5 emu g⁻¹). The predominant superparamagnetic nature is attributed to the citric acid coating. This improves the dispersion and stability of the magnetic cores through the reduction of the dipolar–dipolar interaction and the enhancement of the spin coordination. The rapid adsorption mechanism of FeO@SiO₂–DNA was evaluated through the removal of Pb(ii), As(iii), and Hg(ii). A rapid adsorption rate is observed in the first 15 min, attributed to a heterogeneous chemisorption mechanism based on electrostatic interactions. FeO@SiO₂–DNA shows higher adsorption efficiency of 69% for Pb(ii) removal compared to As(iii) (51%) and Hg(ii) (41%). The selectivity towards Pb(ii) is attributed to the similar acid nature to ds-DNA, where the ionic strength interaction provides good affinity and stability. The facile synthesis and rapid adsorption suggest a promising nanostructure for the remediation of water sources contaminated with heavy metal ions and can be extended to other complex molecules.

Facile synthesis of well-dispersed and magnetic FeO@SiO₂–DNA nanostructures with electrostatic active sites for interaction and rapid adsorption of heavy metals.

Recycling application of waste long-root Eichhornia crassipes in the heavy metal removal using oxidized biochar derived as adsorbents

An oxidized biochar was prepared using long-root Eichhornia crassipes through an aerobic/anaerobic hybrid calcination to recycle its waste plants after eutrophic treatments. The adsorption performances of the biochar were investigated and the results showed that the adsorption equilibrium could arrive in 30 min and the adsorption capacities for Pb²⁺, Cu²⁺, Cd²⁺ and Zn²⁺ at 30 °C were 0.57, 0.41, 0.44 and 0.48 mmol/g, respectively. The adsorption could be promoted at higher pH and temperature and the adsorption tolerance for different heavy metal ions to the existence of competing ions and organic matters was hierarchical. The adsorption was deduced to be heterozygous courses and mainly controlled by complexation of oxygen-containing groups with these heavy metal ions. It was confirmed that the biochar could be regenerated with HCl solution and the adsorption performance kept consistent in 10 adsorption-desorption cycles.

Preparation of ternary amino-functionalized magnetic nano-sized illite-smectite clay for adsorption of Pb(II) ions in aqueous solution

Ternary amino-functionalized magnetic illite-smectite (AMNI/S) nanocomposites were prepared via integrating two-dimensional illite-smectite nanoflakes (NI/S), magnetite nanoparticles (Fe₃O₄), and 3-aminopropyltriethoxysilane (APTES). The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and vibrating sample magnetometry (VSM). The results show that Fe₃O₄ nanoparticles can be well dispersed on NI/S flakes and the hydrolyzed APTES molecules can simultaneously bond to the hydroxyl groups of Fe₃O₄ and NI/S. Due to the synergetic effect, magnetic NI/S composite can graft more amount of APTES molecules rather than Fe₃O₄ nanoparticles or NI/S alone. When the mass ratio of NI/S:Fe₃O₄ is 1:1, the saturation magnetization of AMNI/S-1 is 17.4 emu/g, facilitating the efficient magnetic separation in aqueous solution. Also, AMNI/S-1 shows a maximal adsorption amount of Pb(II) ions of 227.8 mg/g calculated by the Langmuir model. The effects of initial concentration of Pb(II) ions, pH value, adsorption time, and temperature on the adsorption amount of Pb(II) ions were investigated. The adsorption kinetic models and isotherm models were applied to analyze the adsorption of Pb(II) ions, respectively. The thermodynamic analysis reveals that the adsorption of Pb(II) onto AMNI/S-1 is spontaneous and endothermic in nature. The mechanism for the adsorption of Pb(II) ions onto AMNI/S-1 is due to the surface complexation of Fe₃O₄ and NI/S, and the chelation of amine groups (-NH₂). AMNI/S-1 can be efficiently reused and the regenerated AMNI/S-1 remains 82.91% of initial adsorption capacity after 6-cycle adsorption/desorption process. Thus, ternary AMNI/S-1 could be used as a prospective effective adsorbent.

In Situ Copolymerized Polyacrylamide Cellulose Supported Fe3O4 Magnetic Nanocomposites for Adsorptive Removal of Pb(II): Artificial Neural Network Modeling and Experimental Studies

The inimical effects associated with heavy metals are serious concerns, particularly with respect to global health-related issues, because of their non-ecological characteristics and high toxicity. Current research in this area is focused on the synthesis of poly(acrylamide) grafted Cell@Fe3O4 nanocomposites via oxidative free radical copolymerization of the acrylamide monomer and its application for the removal of Pb(II). The hybrid material was analyzed using different analytical techniques, including thermogravimetric analysis (TGA), Fourier transform-infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) analysis. The efficacious impact of variable parameters, including contact time, pH, material dose, initial Pb(II) concentration, and the temperature, was investigated and optimized using both batch and artificial neural networks (ANN). Surface digestion of metal ions is exceedingly pH-dependent, and higher adsorption efficiencies and adsorption capacities of Pb(II) were acquired at a pH value of 5. The acquired equilibrium data were analyzed using different isotherm models, including Langmuir, Freundlich, Temkin, and Redlich-Peterson models. In this investigation, the best performance was obtained using the Langmuir model. The maximum adsorption capacity of the material investigated via monolayer formation was determined to be 314.47 mg g-1 at 323 K, 239.74 mg g-1 at 313 K, and 100.79 mg g-1 at 303 K.

Preparation and characterization of amino/thiol bifunctionalized magnetic nanoadsorbent and its application in rapid removal of Pb (II) from aqueous system

To explore the effect of coexisted amino and thiol groups on adsorption of heavy metal, a novel magnetic nanoparticle was prepared by sequentially modification with (3-Chloropropyl) trimethoxysilan, polyetherimide, epichlorohydrin and thiourea. Subsequently, it was characterized by TEM, N₂ adsorption/desorption, FTIR Spectroscopy, zeta potential, and VSM. The maximum adsorption capacity for Pb²⁺, Cd²⁺ and Cu²⁺ reached 110.13 mg·g^-1, 40.23 mg·g^-1 and 29.37 mg·g^-1, respectively. The adsorption of the magnetic nanoparticles with different surface group for heavy metals were compared, which indicated that the amino and thiol group played an important role in the adsorption of heavy metals. Especially, the adsorption capacity increased dramatically after modification with the thiol group, which was attributed to the synergistic coordination of -NH₂ and -SH. The adsorption kinetics is consistent with the quasi-second-order kinetics equation, and the adsorption thermodynamic process is consistent with the Langmuir isotherm equation. The effects of experimental conditions, such as pH, the concentration of metals, adsorption time and temperature, on adsorption of Pb²⁺ were studied in detail. In addition, over 90% of removal rate was remained after 6 cycles. The magnetic nanoadsorbents was a promising nanoadsorbent with high adsorption speed, simultaneous adsorption of various heavy metals, strong anti-interference ability and reusability.

Competitive adsorption of Cd2+, Pb2+ and Ni2+ onto Fe3+-modified argillaceous limestone: Influence of pH, ionic strength and natural organic matters

In present study, the feasibility of applying a natural adsorbent with Fe³⁺ modification (Fe³⁺-modified argillaceous limestone, FAL) on the competitive adsorption of heavy metals (i.e., Cd²⁺, Pb²⁺ and Ni²⁺) was evaluated. The current results revealed an efficient adsorption on Cd²⁺, Pb²⁺ and Ni²⁺ in mono-metal system. Further experiments demonstrated a high selectivity of Pb²⁺ during the competitive adsorption of Cd²⁺, Pb²⁺ and Ni²⁺. The adsorption selectivity of the metal ions followed the order of Pb ≫ Cd > Ni. In addition, both pH and ionic strength are important factors affecting the metal adsorptions. It is interestingly that various NOMs (i.e., humic acid (HA) and glycine (Gly)) exerted different effects on the adsorption behaviors, probably due to the different affinities for Pb²⁺, Cd²⁺ and Ni²⁺ and the redistribution of newly-formed metal-DOM complexes. X-ray photoelectron spectroscopy (XPS) analysis together with X-ray diffraction (XRD) and energy dispersive spectrometer (EDS) analysis revealed that the metal adsorptions were mainly regulated via the synergistic mechanisms of ion exchange by Na⁺, Ca²⁺, and Al³⁺, precipitation to form CdCO₃ and Pb₂(OH)₂(CO₃)₂, as well as complexes of FAL-OPb and FAL-ONi by hydroxyl groups on the surface of FAL. The application of FAL would be a promising option in leading to an efficient heavy metal removal.

Fabrication of Fe3O4@polydopamine@polyamidoamine core–shell nanocomposites and their application for Cu(ii) adsorption

Fe₃O₄@PDA@PAMAM nanocomposites were fabricated with a polydopamine assisted method, possessing excellent magnetic properties and high adsorption capacity for Cu(ii).