Synthesis of peanut shell based magnetic activated carbon with excellent adsorption performance towards electroplating wastewater

Fe3O4@SiO2@CSH+VO3- as a novel recyclable heterogeneous catalyst with core-shell structure for oxidation of sulfides

Iron nanoparticles, with low toxicity and many active sites, are among the materials that not only reduce waste along with green chemistry but also increase the separation power and recover the catalyst from the reaction environment. In this study, first, the surface of iron nanoparticles was silanized, and in the next step, the complex of chitosan HCl.VO3 was placed on the surface of Fe3O4 (Fe3O4@SiO2@CSH+VO3-). This nanocatalyst is a novel, recoverable, and potent nanocatalyst with high selectivity for the oxidation of sulfides to sulfoxides. Various physicochemical techniques such as IR, XRD, TGA, SEM, EDX, mapping, TEM, and VSM were used to affirm the well synthesis of the catalyst. Oxidation of sulfides in the presence of hydrogen peroxide as a green oxidant and in ethanol was catalyzed by the Fe3O4@SiO2@CSH+VO3-. All sulfoxides were achieved with high efficiency and in a short time. The notable privileges of this method include facile and economic catalyst synthesis, proper catalyst durability, great performance, simple catalyst isolation, good recovery capability, at least up to 5 times without an index drop in catalytic power.

Always positive covalent organic nanosheet enabling pH-independent adsorption and removal of Cr(Ⅵ)

Rapid and highly effective removal of hexavalent chromium (Cr(Ⅵ)) is extremely vital to water resources restoration and environmental protection. To overcome the pH limitation faced by most ionic absorbents, an always positive covalent organic nanosheet (CON) material was prepared and its Cr(VI) adsorption and removal capability was investigated in detail. As-prepared EB-TFB CON (TFB = 1,3,5-benzaldehyde, EB = ethidium bromide) shows strong electropositivity in the tested pH range of 1 ∼ 10, display a pH-independent Cr(VI) removal ability, and work well for Cr(VI) pollution treatment with good anti-interference capability and reusability in a wide pH range covering almost all Cr(VI)-contaminated real water samples, thus eliminating the requirement for pH adjustment. Moreover, the nanosheet structure, which is obtained by a facile ultrasonic-assisted self-exfoliation, endows EB-TFB CON with fully exposed active sites and shortened mass transfer channels, and the Cr(VI) adsorption equilibrium can be reached within 15 min with a high adsorption capacity of 280.57 mg·g-1. The proposed Cr(VI) removal mechanism, which is attributed to the synergetic contributions of electrostatic adsorption, ion exchange and chemical reduction, is demonstrated by experiments and theoretical calculations. This work not only provides a general Cr(VI) absorbent without pH limitation, but also presents a paradigm to prepare ionic CONs with relatively constant surface charges.

A review of novel green adsorbents as a sustainable alternative for the remediation of chromium (VI) from water environments

The presence of heavy metal, chromium (VI), in water environments leads to various diseases in humans, such as cancer, lung tumors, and allergies. This review comparatively examines the use of several adsorbents, such as biosorbents, activated carbon, nanocomposites, and polyaniline (PANI), in terms of the operational parameters (initial chromium (VI) concentration (C_o), temperature (T), pH, contact time (t), and adsorbent dosage) to achieve the Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption. The study finds that the use of biosorbents (fruit bio-composite, fungus, leave, and oak bark char), activated carbons (HCl-treated dry fruit waste, polyethyleneimine (PEI) and potassium hydroxide (KOH) PEI-KOH alkali-treated rice waste-derived biochar, and KOH/hydrochloric acid (HCl) acid/base-treated commercial), iron-based nanocomposites, magnetic manganese-multiwalled carbon nanotubes nanocomposites, copper-based nanocomposites, graphene oxide functionalized amino acid, and PANI functionalized transition metal are effective in achieving high Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption, and that operational parameters such as initial concentration, temperature, pH, contact time, and adsorbent dosage significantly affect the Langmuir's maximum adsorption capacity (q_m). Magnetic graphene oxide functionalized amino acid showed the highest experimental and pseudo-second-order kinetic model equilibrium adsorption capacities. The iron oxide functionalized calcium carbonate (IO@CaCO₃) nanocomposites showed the highest heterogeneous adsorption capacity. Additionally, Syzygium cumini bark biosorbent is highly effective in treating tannery industrial wastewater with high levels of chromium (VI).

Study on adsorption of hexavalent chromium by composite material prepared from iron-based solid wastes

A new adsorbent with chromium removal function was synthesized by carbon thermal method using iron-containing waste Fenton sludge and carbon-containing solid waste fly ash to treat high pH scoring wastewater generated from industrial processes. The results showed that the adsorbent used T = 273.15 K, pH = 10, t = 1200 min, C₀ = 100 mg/L, had a removal rate of Cr(VI) of more than 80%, and the adsorption capacity could reach 393.79 mg/g. The characterization results show that the synthesized mesoporous nitrogen-doped composite material has a large specific surface area and mesoporous structure, and the surface of the material is rich in oxygen-containing functional groups and active sites. Compared with other studies, the adsorption capacity of the material is larger, which indicates that the removal effect of Cr(VI) in this study is better. The adsorption kinetic results show that the adsorption follows a pseudo second kinetic model, and the adsorption process is a chemisorption involving electron sharing or electron exchange. This experiment designed a simple method to synthesize mesoporous nitrogen-doped composites using industrial solid waste, with raw materials from cheap and easily available industrial solid waste, and solved the dual problems of heavy metals in wastewater and solid waste, providing a new idea for the resource utilization of Fenton sludge while not producing secondary pollution.

Highly effective removal of nickel ions from wastewater by calcium-iron layered double hydroxide

Water pollution due to heavy metals has become a universal environmental problem. Ni(II) is a common heavy metal ion in polluted wastewater, which has high toxicity and carcinogenicity. In this study, the structure of a calcium-iron layered double hydroxide (Ca-Fe-LDHs) was synthesized and characterized by FTIR, XRD, SEM and XPS. Then, Ni(II) ion was effectively removed by Ca-Fe-LDHs and its mechanism for this materials was described. The maximum adsorption capacity of Ni(II) for Ca-Fe-LDHs was 418.9 mg‧g^-1 when the initial concentration of Ni(II) was 1 g/L. The adsorption and removal of Ni(II) by Ca-Fe-LDHs was attributed to the action of hydroxyl groups on the hydrotalcite, generating surface capture. Ni(OH)₂)0.75(H₂O)0.16(NiCO₃)0.09, Ni(OH)₂, NiO, NiSO₄ and other precipitates were generated on its surface. And a small amount of Ni-Fe-LDHs was generated through isomorphic transition before hydrolysis. Therefore, surface capture and isomorphic transition enhanced the removal efficiency of Ni(II) with Ca-Fe-LDHs, making Ca-Fe-LDHs as a potential material for effective removal of Ni(II).

Removal of decidedly lethal metal arsenic from water using metal organic frameworks: a critical review

Water contamination is worldwide issue, undermining whole biosphere, influencing life of a large number of individuals all over the world. Water contamination is one of the chief worldwide danger issues for death, sickness, and constant decrease of accessible drinkable water around the world. Among the others, presence of arsenic, is considered as the most widely recognized lethal contaminant in water bodies and poses a serious threat not exclusively to humans but also towards aquatic lives. Hence, steps must be taken to decrease quantity of arsenic in water to permissible limits. Recently, metal-organic frameworks (MOFs) with outstanding stability, sorption capacities, and ecofriendly performance have empowered enormous improvements in capturing substantial metal particles. MOFs have been affirmed as good performance adsorbents for arsenic removal having extended surface area and displayed remarkable results as reported in literature. In this review we look at MOFs which have been recently produced and considered for potential applications in arsenic metal expulsion. We have delivered a summary of up-to-date abilities as well as significant characteristics of MOFs used for this removal. In this review conventional and advanced materials applied to treat water by adsorptive method are also discussed briefly.

Activated biochar derived from peanut shells as the electrode materials with excellent performance in Zinc-air battery and supercapacitance

The use of activated biochar-based electrode derived from waste biomass in energy technologies, such as metal-air batteries and supercapacitors, is an important strategy for realizing energy and environmental sustainability in the future. Herein, peanut shells (waste biomass) were employed to prepare activated biochar materials by pyrolysis in molten KCl and heat-treatment. The effective dispersion and corrosion effects of molten salt for the pyrolysis products during pyrolysis obviously increase defects and specific surface area of the activated biochar materials. The prepared activated biochar material (PS-800-1000) by pyrolysis in molten KCl at 800 °C and heat-treatment at 1000 °C exhibits excellent catalytic activity with half-wave potential of 0.84 V vs. RHE, comparable to commercial Pt/C for oxygen reduction reaction (ORR) in 0.1 M KOH and outstanding supercapacitance performance in 6 M KOH with high specific capacitance (355 F g^-1 at 0.5 A g^-1), which exceeds all reported biochar derived from peanut shells. The PS-800-1000-based zinc-air battery (ZAB) displays higher peak power density (141 mW cm^-2), specific capacity (767 mAh g_Zn^-1) and cycling stability than Pt/C-based ZAB. The activated biochar prepared by pyrolysis in molten KCl and heat-treatment method from peanut shells can be a promising candidate for replacing precious metals in energy conversion/storage devices.

Insights of competitive adsorption on activated carbon of binary caffeine and diclofenac solutions

A commercial activated carbon (AC), obtained from peanut shells, was characterized and tested as adsorbent for the removal of the pharmaceutical products caffeine (CF) and diclofenac (DIC), which were used as model emerging contaminants. Nitrogen adsorption, XRD, SEM, FT-IR spectroscopy, and chemical analyses were typical of ACs, and Boehm titrations, calculations of surface sites distributions and zeta potential measurements indicated that reactions of deprotonable oxygenated groups at the AC surface lead to an isoelectric point of 3.2. A theoretical equation derived from the Langmuir isotherm is proposed to explain the adsorption percentage or adsorbed fraction (f_ads) as a function of the adsorbent dose (D, adsorbent "concentration"). Good fittings of the f_ads vs. D curves and the normal adsorption isotherms were obtained with the same Langmuir parameters. An important and practical application of this new equation is to permit a straightforward calculation of the solid dose needed to achieve a required adsorption percentage. With the aim of describing the adsorption processes of CF and DIC and their competition for surface sites under an ample range of concentrations, the adsorption of the emerging contaminants was investigated in single adsorbate experiments and with binary mixtures, and the competitive Langmuir model was applied. CF adsorption was high and independent of pH, whereas DIC adsorption was high between pH 4 and 6 and showed a continuous decrease from pH 6 to 10.5. The use of the competitive Langmuir isotherm for binary mixtures indicated that there was no pure competition between CF and DIC for surface sites. Instead, there was influenced competition, meaning that the presence of one substance at the surface modified the adsorption parameters of the other, either through lateral interaction forces or by changing the molecular orientation at the surface. In both cases, one substance favored the adsorption of the other, compared to pure competition.

Flower-like hierarchical ZnS-Ga2S3 heterojunction for the adsorption-photo-reduction of Cr(VI)

Adsorption-photo-reduction is considered as a potential route to remove Cr(VI) from wastewater. To explore the novel photocatalysts with efficient adsorption-photocatalytic activity, flower-like hierarchical ZnS-Ga₂S₃ heterojunction was prepared for the solar-light-driven reduction of Cr(VI). Its adsorption-photocatalytic capacity is greatly affected by the ZnS/Ga₂S₃ molar ratio, Cr(VI) content, pH values, and inorganic ions. Among these obtained composites, ZnS-Ga₂S₃-3 with a ZnS/Ga₂S₃ molar ratio of 3:1 exhibits the best adsorption-photocatalytic capacity. The adsorption capacity of ZnS-Ga₂S₃-3 is 54.42 mg g^-1, and its total removal efficiency is 99.10% for 100 mg L^-1 Cr(VI) solution after 160 min. In addition, the adsorption-photo-reduction performance of ZnS-Ga₂S₃-3 is slightly deactivated after nine cycle times. The Langmuir, pseudo-second-order, and first-order models well describe the adsorption isotherm, adsorption kinetic, and photo-reduction kinetic of ZnS-Ga₂S₃-3, respectively. The synergy effect of ZnS and Ga₂S₃ are favorable for the efficient transfer and separation of charge carriers, and provide sufficient vacant sites at the junction interface for the adsorption of Cr(VI).

Preparation of 2D nitrogen-doped magnetic Fe3C/C by in-situ self-assembled double-template method for enhanced removal of Cr(VI)

Porous carbon, which can be functionalized, is considered as a potential carbon material. Herein, two-dimensional (2D) nitrogen-doped magnetic Fe₃C/C (NMC) was prepared by a simple carbonization method using potassium humate (HA-K) as raw material. Remarkably, two templates, g-C₃N₄ and KCl, were formed in situ during the carbonization process, which provide the necessary conditions for the formation of 2D NMC. The NMC was comprehensively studied by different characterization methods. The results show that NMC has a large surface area and mesoporous structure. The prepared NMC-0.50 was used to test the removal performance of Cr(VI). The effects of pH value, coexisting ions and time on Cr(VI) removal performance were investigated, and the adsorption kinetics, isotherm and thermodynamics were studied. The results showed that the adsorption isotherm model of NMC-50 accorded with the Langmuir model, and the maximum adsorption capacity was 423.73 mg g^-1. The reaction mechanism of Cr(VI) is adsorption and redox reaction. In addition, NMC-0.50 exhibit high selectivity, separability and regeneration performance. A convenient means for the synthesis of NMC was designed in this work, and demonstrate that NMC has practical value as an adsorbent.

Synthesis of amino-functionalized biochar/spinel ferrite magnetic composites for low-cost and efficient elimination of Ni(II) from wastewater

Novel amino-modified rice bran biochar/MgFeAlO₄ (RB@MgFeAlO₄-NH₂) magnetic composites were synthesized via a simple one-step solvothermal approach and applied for removing toxic Ni(II) from wastewater. The elimination process and sorption performance of Ni(II) on RB@MgFeAlO₄-NH₂ were analyzed by combining batch experiments and spectral techniques. The sorption isotherms and kinetic data indicated that Ni(II) sorption on RB@MgFeAlO₄-NH₂ was monolayer and rapid. The experimental results confirmed that the obtained RB@MgFeAlO₄-NH₂ magnetic composite had high sorption capacity for Ni(II). The maximum sorption capacity of Ni(II) on RB@MgFeAlO₄-NH₂ was 201.62 mg g^-1. The researches based on the sorption mechanism showed that the ion exchange mechanism accounted for 76.51% of Ni(II) sorption. In addition, the amino, carboxyl and hydroxyl functional groups were also involved in the complexation with Ni(II). In view of its multiple advantages of environmental friendliness, low cost, easy magnetic separation and high sorption capacity, RB@MgFeAlO₄-NH₂ will be an excellent adsorbent for low-cost and efficient elimination of Ni(II) from aqueous solutions.

Valorization of poly(ethylene)terephthalate wastes into nanoporous carbons for the adsorption of 1,3-diphenylguanidine from an aqueous solution

Carbon prepared by using MgO templating and KOH activation has a better absorption capacity for DPG.

One-pot solvothermal synthesis of magnetic biochar from waste biomass: Formation mechanism and efficient adsorption of Cr(VI) in an aqueous solution

A facile one-pot solvothermal method was applied to synthesize a magnetic biochar composite (MB) using phoenix tree leaves-derived biochar as the carbon matrix. The structure of MB was optimized by varying the load ratio and particle size of Fe₃O₄ nanoparticles on biochar. Time-dependent structure and composition evolution of solid and liquid phases during heterogeneous solvothermal process were investigated to understand the formation mechanism of MB. Firstly, Fe²⁺/Fe³⁺ ions were coordinated by oxygen-containing groups on biochar and part of them were hydrolyzed to form iron hydroxides. Then, those iron-containing precursors were thermally decomposed and reduced to iron oxides; and finally Fe₃O₄ nanoparticles were generated. The MB had an adsorption capacity for Cr(VI) of 55.0 mg/g in an aqueous solution, which exceeds those of biochar (39.8 mg/g) and Fe₃O₄ nanoparticles (26.5 mg/g). The adsorption mechanism study reveals that biochar as a carbon skeleton mainly provided binding sites for Cr(VI) and electron-donor groups for reduction of Cr(VI), while Fe₃O₄ nanoparticles mainly involved in the immobilization of newly formed Cr(III) through formation of Fe(III)-Cr(III) hydroxide. MB exhibited a stable structure with a lower Fe leakage at pH 2.0 than that of a comparable magnetic biochar sample prepared by conventional co-precipitation method. Recycling experiments suggested that MB could keep 84% of its initial removal capability for Cr(VI) even after seven cycles. The results indicate that solvothermal method is a promising alternative to prepare magnetic biochar for adsorption of heavy metal-containing wastewater.

Modelling on the removal of toxic metal ions from aquatic system by different surface modified Cassia fistula seeds

The present work demonstrates the preparation of Cassia fistula seeds for producing activated carbon through physical and chemical treatment for the extrusion of Ni(II) ion contaminated aqueous solution. The readily prepared sorbents were characterized using SEM-EDX and FTIR. The surface morphology of sorbents possesses 1 μm mean particle size with uniform size distribution. Furthermore, optimization of operating parameters such as the pH, initial Ni(II) ion concentration, adsorbent dose, time and temperature were investigated. In isotherm and kinetic aspect, Langmuir maximum adsorption capacity of sulphuric acid modified Cassia fistula seeds was 182.2 (mg/g); obeyed Pseudo first order kinetic model. The Ni(II) ion adsorption system undergoes chemisorption, exothermic, feasible and spontaneous. The excellent properties of the Cassia fistula seeds can be alternate for commercial activated carbon.