Catalytic wet peroxide oxidation of vanillic acid as a lignin model compound towards the renewable production of dicarboxylic acids

Lignin removal from synthetic wastewater via Fenton-like reaction over Cu supported on MCM-41 derived from bagasse: Optimization and reaction intermediates

Lignin degradation was performed using a Fenton-like oxidation reaction with Cu supported on MCM-41, derived from bagasse (Cu-BG-MCM-41), as the catalyst. The optimal degradation conditions required to remove a predetermined amount of lignin (95%) from an effluent were determined. Based on the literature review and preliminary tests, the critical parameters determining the operating conditions include temperature, catalyst loading, pH, H₂O₂ concentration, and reaction time. The experimental design and working conditions were based on Box-Behnken design. The reaction products were analyzed via UV-vis and gas chromatography-mass spectrometry. Response surface methodology (RSM) was used to predict the optimum operating conditions for the Fenton-like reaction for 95% lignin degradation, which were a temperature of 80 °C, initial pH of 9, H₂O₂ concentration of 1 mL/L, catalyst loading of 1.0 g/L, and reaction time of 30 min. These conditions were validated three times and the achieved percentage of lignin degradation was 95 ± 2%. This is close to the value of 95% used in the RSM to determine the optimum operating conditions, thus verifying the model. The catalyst was stable and functioned well under the optimum design conditions. Moreover, the reaction could be used to obtain high-value intermediate products if stopped after 5 min. Finally, lignin was degraded into vanillin, a higher-value product. As expected, the proposed Fenton-like approach expanded the pH working range from less than 4 to 5-9.

Microwave-Assisted Lignin Wet Peroxide Oxidation to C4 Dicarboxylic Acids

Innovative methodologies, such as microwave-assisted reaction, can help to valorize lignin with higher productivity and better energy efficiency. In this work, microwave heating was tested in the wet peroxide oxidation of three lignins (Indulin AT, Lignol, and Eucalyptus globulus lignins) as a novel methodology to obtain C₄ dicarboxylic acids. The effect of temperature, time, and catalyst type (TS-1 or Fe-TS1) was evaluated in the production of these acids. The TS-1 catalyst improved succinic acid yield, achieving up to 9.4 wt % for Lignol lignin. Moreover, the microwave heating specifically enhanced Lignol conversion to malic acid (34 wt %), even without catalyst, showing to be an attractive path for the future valorization of organosolv lignins. Overall, compared to conventional heating, microwave heating originated a rapid lignin conversion. Nevertheless, for prolonged times, conventional heating led to better results for some target products, e.g., malic and succinic acids.

Cleavage via Selective Catalytic Oxidation of Lignin or Lignin Model Compounds into Functional Chemicals

Lignin, a complex aromatic polymer with different types of methoxylated phenylpropanoid connections, enables the sustainable supply of value-added chemicals and biofuels through its use as a feedstock. Despite the development of numerous methodologies that upgrade lignin to high-value chemicals such as drugs and organic synthesis intermediates, the variety of valuable products obtained from lignin is still very limited, mainly delivering hydrocarbons and oxygenates. Using selective oxidation and activation cleavage of lignin, we can obtain value-added aromatics, including phenols, aldehydes, ketones, and carboxylic acid. However, biorefineries will demand a broad spectrum of fine chemicals in the future, not just simple chemicals like aldehydes and ketones containing simple C = O groups. In particular, most n-containing aromatics, which have found important applications in materials science, agro-chemistry, and medicinal chemistry, such as amide, aniline, and nitrogen heterocyclic compounds, are obtained through n-containing reagents mediating the oxidation cleavage in lignin. This tutorial review provides updates on recent advances in different classes of chemicals from the catalytic oxidation system in lignin depolymerization, which also introduces those functionalized products through a conventional synthesis method. A comparison with traditional synthetic strategies reveals the feasibility of the lignin model and real lignin utilization. Promising applications of functionalized compounds in synthetic transformation, drugs, dyes, and textiles are also discussed.

Added-Value Chemicals from Lignin Oxidation

Lignin is the second most abundant component, next to cellulose, in lignocellulosic biomass. Large amounts of this polymer are produced annually in the pulp and paper industries as a coproduct from the cooking process-most of it burned as fuel for energy. Strategies regarding lignin valorization have attracted significant attention over the recent decades due to lignin's aromatic structure. Oxidative depolymerization allows converting lignin into added-value compounds, as phenolic monomers and/or dicarboxylic acids, which could be an excellent alternative to aromatic petrochemicals. However, the major challenge is to enhance the reactivity and selectivity of the lignin structure towards depolymerization and prevent condensation reactions. This review includes a comprehensive overview of the main contributions of lignin valorization through oxidative depolymerization to produce added-value compounds (vanillin and syringaldehyde) that have been developed over the recent decades in the LSRE group. An evaluation of the valuable products obtained from oxidation in an alkaline medium with oxygen of lignins and liquors from different sources and delignification processes is also provided. A review of C4 dicarboxylic acids obtained from lignin oxidation is also included, emphasizing catalytic conversion by O2 or H2O2 oxidation.