Determination of the herbicide metribuzin and its major conversion products in soil by micellar electrokinetic chromatography

Rapid Determination of Metribuzin and Three Major Transformation Products in Soil and Plant by Gas Chromatography–Tandem Mass Spectrometry

Metribuzin is a pre- and post-emergence triazinone herbicide used in a variety of crops. This herbicide is degraded in the environment into three major metabolites that have high water solubility, high to very high soil mobility, and low to moderate persistence in soil. This paper describes the development of an analytical method based on ultrasound-assisted extraction and GC-MS/MS determination for the determination metribuzin and its main metabolites in soil and plants. The developed method provided good recoveries for all compounds in soil and plants (from 73 to 121%). The quantitation limits obtained from plants (2.6 to 18 µg/kg) allow determining the presence of these compounds at trace levels. To evaluate the applicability of the developed methods, bean plants were grown in plastic pots with soil treated with metribuzin and collected after 23 days. At the end of the assay, only 11% of the initial concentration of metribuzin remained in soil. Metribuzin and its three metabolites were detected in plants, desamino-diketo-metribuzin is the most abundant metabolite. It is expected that the application of these methods can provide more data to monitor metribuzin residues due to herbicide treatments.

Adsorption of metribuzin from aqueous solution using magnetic and nonmagnetic sustainable low-cost biochar adsorbents

Switchgrass biochar (SGB) was made by fast pyrolysis in an auger-fed reactor at 425 °C with a solid residence time of 60 s in the pyrolysis zone during bio-oil production. Magnetic switchgrass biochar (MSGB) was prepared by iron oxide precipitation onto the biochar surface using an aqueous Fe³⁺/Fe²⁺ solution followed by NaOH treatment. Both the SGB and the MSGB were characterized by FTIR, SEM, SEM-EDX, TGA, pH_pzc, elemental analysis, and surface area measurements. Batch sorption studies of metribuzin from aqueous solutions were carried out at different pH values, adsorbate concentrations, and temperatures. The adsorption of metribuzin onto both biochars was highest at a pH of 2. Adsorption isotherms were evaluated from 25 to 45 °C using the Freundlich, Langmuir, Redlich-Peterson, Toth, Sips, Koble-Corrigan, and Radke-Prausnitz adsorption models. Langmuir adsorption capacities at pH 2 were Q ⁰_SGB ~ 151, 223, and 205 mg/g and Q ⁰_MSGB ~ 155, 205, and 155 mg/g at 25, 35, and 45 °C, respectively. Low-cost magnetization of the biochar occurred without significant loss of absorption capacity, enabling facile separation of slurried biochar from liquids following contaminate absorption. Graphical abstract ᅟ.

MEKC as a powerful growing analytical technique

This review summarizes the principle and the developments in MEKC in terms of separation power, sensitivity, and detection approaches more than 25 years after its appearance. Newly used surfactants are mentioned. Classical and new sample concentration techniques in MEKC are described. The different detection approaches in MEKC with advantages, limitations, and future prospects are also discussed. This review highlights the wider application of MEKC in different analytical fields. Various recent selected applications of this technique in different analytical fields are reported.

SPE and large-volume sample stacking in MEKC for determination of doxycycline in biological fluids: comparison of direct injection to SPE-MEKC

A novel and simple method has been developed for the determination of doxycycline (DOX) in biological fluids. The method is based on SPE, large-volume sample stacking (LVSS) and MEKC with UV-DAD detection. Six SPE cartridges have been used in investigation for sample clean up and pre-concentration (Supelco LC-8, LC-18, LC-SCX, and LC-WCX, as well as Strata-X and X-C). DOX was determined on a 56 cm (effective length 50 cm) x 50 microm id fused-silica capillary. The BGE was 20 mM borate buffer, pH 9.3, containing 80 mM SDS and 7.5% v/v of methanol (30 sx50 mbar), and the temperature and voltage were 25 degrees C and 30 kV, respectively. The analytical wavelength was set at 210 nm. Under optimized conditions it is possible to determine DOX in human serum, urine, semen, tears and saliva with recovery of 97.5% (RSD 2.5%). The method was shown to be sensitive (LOD is 1 microg/L) and precise (intra-day RSD 0.2 and 2.4%; inter-days 0.4 and 3.5% for migration time and peak area, respectively). Results for developed SPE-LVSS-MEKC were compared with LVSS-MEKC method with direct sample injection. The new LVSS-MEKC method is presented as a useful technique for rapid determination without extraction procedure of DOX in human urine and serum, using 80 mM of SDS, 10% v/v of methanol and 40 mM borate buffer (pH 9.3; 30 s x 50 mbar; 25 degrees C; 30 kV; 350 nm), but not for the other biological fluids, according to lower sensitivity of the method and because of the sample composition.

Large volume sample stacking in capillary zone electrophoresis for the monitoring of the degradation products of metribuzin in environmental samples

A capillary zone electrophoresis (CZE) method with UV-vis detection has been developed for the simultaneous monitoring of the major degradation products of metribuzin, i.e. deaminometribuzin (DA), deaminodiketometribuzin (DADK) and diketometribuzin (DK). The dissociation acid constants have also been estimated by CE and no significant differences have been observed with the values obtained by applying other techniques. Optimum separation has been achieved in less than 9 min in 40 mM sodium tetraborate buffer, pH 9.5 by applying a voltage of 15kV at 25 degrees C and using p-aminobenzoic acid as internal standard. In order to increase sensitivity, large volume sample stacking (LVSS) with polarity switching has been applied as on-line pre-concentration methodology. Detection limits of 10, 10 and 20 ng/mL for DA, DADK and DK, respectively were obtained. The method has been applied to soil samples, after pressurized liquid extraction (PLE). Samples were extracted at high temperature (103 degrees C and 1500 psi) using methanol as extraction solvent and sodium sulphate as drying agent. This PLE procedure was followed by an off-line pre-concentration and sample clean-up procedure by solid-phase extraction (SPE) using a LiChrolut EN sorbent column. These last two procedures were also suitable for the direct treatment of groundwater samples before CE analysis. The combination of both off-line and on-line pre-concentration procedures provided a significant improvement in sensitivity. LVSS provided pre-concentration factors of 4, 36 and 28 for DK, DA and DADK, respectively and with SPE a pre-concentration of 500-fold for the case of water samples and of 2.5-fold in the case of soil samples was obtained. The method is suitable for the monitoring of these residues in environmental samples with high sensitivity, precision and satisfactory recoveries.

Pesticides analysis by liquid chromatography and capillary electrophoresis

Nowadays, a wide range of pesticides are used in agricultural production, and their monitoring in samples of environmental and alimentary interest is of extreme importance to ensure, among others, the safety of consumption of foods. The aim of this work is to provide updated information about the major developments in CE and HPLC in pesticide analysis, covering relevant publications between 2004 and early 2006. The use of different sample pretreatment steps to provide a suitable extraction of these compounds from the different matrices as well as to increase the sensitivity of the determination is also discussed.