Simultaneous extraction and clean-up of polybrominated diphenyl ethers and polychlorinated biphenyls from sheep liver tissue by selective pressurized liquid extraction and analysis by gas chromatography–mass spectrometry

Influences of humic acid on the release of polybrominated diphenyl ethers from plastic waste in landfills under different environmental conditions

Landfill-formed humic acid are an important substance in landfill leachate. The effect of landfill-formed humic acid in different environments (temperature and surfactant concentrations) on the release of chemicals from plastic waste remains unknown. In order to explore the pollution release rates of polybrominated diphenyl ethers (PBDEs) in different plastic waste, humic acid were used as the extractant to conduct leaching simulation tests to study the effects of time, temperature, and surfactant (sodium dodecyl benzene sulfonate (SDBS)) concentrations on the release of PBDEs in waste. This waste includes polypropylene random pipes (PPRP), polyethylene of raised temperature resistance pipes (PERTP), polyvinyl chloride pipes (PVCP), polypropylene plastic benches (PPB), polypropylene washing machines (PPWM), polystyrene television (PSTV), and flame-retardant acrylonitrile butadiene styrene (FRABS). The leaching amounts of PBDEs had significant linear growth over time. Among them, the leaching amount of PBDEs in daily plastics is lower than dismantling plastics. The rate of leaching of BDE-209 was greater than the other congeners, with a leaching amount of up to 93.10%. Different types of waste exhibited different changes with temperature and surfactants concentrations. Among all the waste types, the leaching amounts of PBDEs in PPRP and PERTP gradually increased with increasing temperature. Surfactants within a certain concentration range can promote the release of PBDEs. The purpose of the research is to explore the dissolution law of PBDEs of different plastic products and the same product in different environment, provides a theoretical basis for the management and risk control of landfills.

Optimization of a new selective pressurized liquid extraction methodology for determining organic pollutants in wild boar livers

In this study, a new selective pressurised liquid extraction (SPLE) methodology was optimised for determining about 70 organic pollutants (OPs) including organochlorine (OCPs), organophosphate (OPPs) and pyrethroid (PYRs) pesticides, polychlorinated biphenyls (PCBs), polybromodiphenyl ethers (PBDEs), as well as, polycyclic aromatic hydrocarbons (PAHs) in wild boar liver samples considering the temperature, pressure and time of contact between the solvent and the matrix as influential variables. Clean-up of extracts was performed by solid-phase extraction (SPE) using EZ-POP cartridges. Detection of OPs was carried out by gas chromatography (GC) coupled to tandem mass spectrometry (QqQ-MS/MS). This new approach offers:•

A new non-time consuming SPLE methodology for determining about 70 OPs in wild boar.

•

Recoveries achieved ranged between 74 to 119 % with RSD less than 20 %.

•

Detection and quantification limits in the low to mid pg/g range.

Polybrominated diphenyl ethers in the environmental systems: a review

PBDEs are human-influenced chemicals utilized massively as flame retardants. They are environmentally persistent, not easily degraded, bioaccumulate in the biological tissue of organisms, and bio-magnify across the food web. They can travel over a long distance, with air and water being their possible transport media. They can be transferred to non-target organisms by inhalation, oral ingestion, breastfeeding, or dermal contact. These pollutants adsorb easily to solid matrices due to their lipophilicity and hydrophobicity; thus, sediments from rivers, lakes, estuaries, and ocean are becoming their major reservoirs aquatic environments. They have low acute toxicity, but the effects of interfering with the thyroid hormone metabolism in the endocrine system are long term. Many congeners of PBDEs are considered to pose a danger to humans and the aquatic environment. They have shown the possibility of causing many undesirable effects, together with neurologic, immunological, and reproductive disruptions and possible carcinogenicity in humans. PBDEs have been detected in small amounts in biological samples, including hair, human semen, blood, urine, and breastmilk, and environmental samples such as sediment, soil, sewage sludge, air, biota, fish, mussels, surface water, and wastewater. The congeners prevailing in environmental samples, with soil being the essential matrix, are BDE 47, 99, and 100. BDE 28, 47, 99, 100, 153, 154, and 183 are more frequently detected in human tissues, whereas in sediment and soil, BDE 100 and 183 predominate. Generally, BDE 153 and 154 appear very often across different matrices. However, BDE 209 seems not frequently determined, owing to its tendency to quickly breakdown into smaller congeners. This paper carried out an overview of PBDEs in the environmental, human, and biota niches with their characteristics, physicochemical properties, and fate in the environment, human exposure, and health effects.

Determination of multi-class polyaromatic compounds in sediments by a simple modified matrix solid phase dispersive extraction

A simple, efficient matrix solid phase dispersive extraction (MSPD) method was optimised to analyse simultaneously polycyclic aromatic hydrocarbons (PAHs) and polychlorobiphenyls (PCBs) from sediments, and was compared to microwave-assisted extraction (MAE). New dispersing agents were tested to improve MSPD extraction. 3-chloropropyl-bonded silica particles, in addition to Florisil, increased significantly the polyaromatics desorption capacity. A compromise was found for eluting both families of compounds from sediments, using a small volume of hexane/acetone. Low procedural detection limits could be reached (0.06-0.22 ng g^-1 and 0.3-1.1 ng g^-1 for PAHs and PCBs, respectively). Mean total extraction recoveries were good for PAHs (>67%, depending on the sediment) and for PCBs (>89%), with good precision (6-9% and 4-10% inter-day precision for PAHs and PCBs, respectively). Higher recoveries for PCBs could be reached in comparison with formerly developed sonication or Soxhlet extraction methods, but also with MAE. MSPD offered significant decrease of sample amount, of solvent consumption and allowed more efficient cleaning of the sediment matrix, leading to less matrix effects compared to MAE, removing lots of interfering compounds without additional purification step. The robustness of the MSPD methodology could be demonstrated extracting quantitatively sediments from different sources and with various mineralogical characteristics.

Polychlorinated Biphenyl Profile in Polyhydroxy-alkanoates Synthetized from Urban Organic Wastes

The microbial synthesis of polyhydroxyalkanoates (PHA) from organic wastes is a valuable process to valorize available renewable resources, such as food wastes and biological sludge. Bioplastics find many applications in various sectors, from medical field to food industry. However, persistent organic pollutants could be transferred from wastes to the final product. The present paper demonstrates that the use of municipal wastes in PHA production is safe for the environment and human health and provides a polychlorinated biphenyl (PCB) profile in both commercial and waste-based PHA samples. PCB analysis in several PHA samples showed very low concentrations of the target analytes. Commercial PHA samples showed a similar PCB level with respect to PHA samples from municipal waste/sludge and higher than PHA samples from fruit waste. For all analyzed PCBs, detected concentrations were consistently lower than the ones reported in regulatory framework or guidelines.

Quantification of polybrominated diphenyl ethers (PBDEs) in food. A review

The polybrominated diphenyl ethers (PBDEs), a class of brominated flame retardants (BFRs), are food contaminants of animal origin. Interest in food matrices analysis is growing due to the toxicity of PBDEs and European Commission (EC) recommendation (118/2014/EU). Here we review papers concerning methods of PBDEs analysis while focusing on extraction, clean up, chromatographic separation and detection techniques. The emphasis is put on EC recommendation, the congeners and the efficiency of different detection systems. Some analytical problems caused by differences between low- and high-molecular-mass congener properties, especially the possible limitations of BDE-209 analysis, are discussed. Detection techniques and mass spectrometry (MS) ionization modes applied to PBDE level determination in food of animal origin are compared. The gas chromatography (GC) coupled to high-resolution MS is undoubtedly fit for that purpose, but ion trap MS could be used to PBDEs determination as well. ECD is the most sensitive technique; however, other halogen compounds present in sample may interfere with PBDEs congeners necessitating results confirmation. Moreover, the novel atmospheric pressure chemical ionization (APCI) method applied to GC in tandem with MS places this technique in the top category of the most sensitive techniques which may be used.

Procedures of determining organic trace compounds in municipal sewage sludge-a review

Sewage sludge is the largest by-product generated during the wastewater treatment process. Since large amounts of sludge are being produced, different ways of disposal have been introduced. One tempting option is to use it as fertilizer in agricultural fields due to its high contents of inorganic nutrients. This, however, can be limited by the amount of trace contaminants in the sewage sludge, containing a variety of microbiological pollutants and pathogens but also inorganic and organic contaminants. The bioavailability and the effects of trace contaminants on the microorganisms of soil are still largely unknown as well as their mixture effects. Therefore, there is a need to analyze the sludge to test its suitability before further use. In this article, a variety of sampling, pretreatment, extraction, and analysis methods have been reviewed. Additionally, different organic trace compounds often found in the sewage sludge and their methods of analysis have been compiled. In addition to traditional Soxhlet extraction, the most common extraction methods of organic contaminants in sludge include ultrasonic extraction (USE), supercritical fluid extraction (SFE), microwave-assisted extraction (MAE), and pressurized liquid extraction (PLE) followed by instrumental analysis based on gas or liquid chromatography and mass spectrometry.

Distribution of persistent organic pollutants (POPS) IN wild Bluefin tuna (Thunnus thynnus) from different FAO capture zones

Residues of environmental contaminants in food represent a concern in food safety programs. In this study, the distribution of persistent organic pollutants (POPs) were evaluated in 79 tuna samples from FAO areas 51 (Indian Ocean), 71 (Pacific Ocean), 34 (Atlantic Ocean), and 37 (Mediterranean Sea). 6 polychlorinated biphenyls (PCBs), 16 organochlorines (OCs) and 7 polybrominated biphenyl ethers (PBDEs) were selected as representative compounds according to EFSA POPs monitoring guidelines. An analytical method, based on Accelerated Solvent Extraction (ASE), with an "in-line" clean-up step and GC-MS/MS detection, was developed, validated and applied. PCBs were detected in all FAO areas, with a prevalence of 100% for most of them. In the FAO area 37, only, all PBDEs were detected. Only 5 OCs were detected. The results showed that POPs contamination of tuna reflects FAO area contamination; in particular FAO area 37 was the most polluted. Moreover, tuna muscle was an appropriate matrix for monitoring contamination and for obtaining information about food safety.

State of the art of environmentally friendly sample preparation approaches for determination of PBDEs and metabolites in environmental and biological samples: A critical review

Green chemistry principles for developing methodologies have gained attention in analytical chemistry in recent decades. A growing number of analytical techniques have been proposed for determination of organic persistent pollutants in environmental and biological samples. In this light, the current review aims to present state-of-the-art sample preparation approaches based on green analytical principles proposed for the determination of polybrominated diphenyl ethers (PBDEs) and metabolites (OH-PBDEs and MeO-PBDEs) in environmental and biological samples. Approaches to lower the solvent consumption and accelerate the extraction, such as pressurized liquid extraction, microwave-assisted extraction, and ultrasound-assisted extraction, are discussed in this review. Special attention is paid to miniaturized sample preparation methodologies and strategies proposed to reduce organic solvent consumption. Additionally, extraction techniques based on alternative solvents (surfactants, supercritical fluids, or ionic liquids) are also commented in this work, even though these are scarcely used for determination of PBDEs. In addition to liquid-based extraction techniques, solid-based analytical techniques are also addressed. The development of greener, faster and simpler sample preparation approaches has increased in recent years (2003-2013). Among green extraction techniques, those based on the liquid phase predominate over those based on the solid phase (71% vs. 29%, respectively). For solid samples, solvent assisted extraction techniques are preferred for leaching of PBDEs, and liquid phase microextraction techniques are mostly used for liquid samples. Likewise, green characteristics of the instrumental analysis used after the extraction and clean-up steps are briefly discussed.

Determination of polychlorinated biphenyls in soil and sediment by selective pressurized liquid extraction with immunochemical detection

A selective pressurized liquid extraction (SPLE) method was developed for a streamlined sample preparation/cleanup to determine Aroclors and coplanar polychlorinated biphenyls (PCBs) in soil and sediment. The SPLE was coupled with an enzyme-linked immunosorbent assay (ELISA) for an effective analytical approach for environmental monitoring. Sediment or soil samples were extracted with alumina, 10% AgNO3 in silica, and sulfuric acid impregnated silica with dichloromethane at 100°C and 2000 psi. The SPLE offered simultaneous extraction and cleanup of the PCBs and Aroclors, eliminating the need for a post-extraction cleanup prior to ELISA. Two different ELISA methods: (1) an Aroclor ELISA and (2) a coplanar PCB ELISA were evaluated. The Aroclor ELISA utilized a polyclonal antibody (Ab) with Aroclor 1254 as the calibrant and the coplanar PCB ELISA kit used a rabbit coplanar PCB Ab with PCB-126 as the calibrant. Recoveries of Aroclor 1254 in two reference soil samples were 92±2% and 106±5% by off-line coupling of SPLE with ELISA. The average recovery of Aroclor 1254 in spiked soil and sediment samples was 92±17%. Quantitative recoveries of coplanar PCBs (107-117%) in spiked samples were obtained with the combined SPLE-ELISA. The estimated method detection limit was 10 ng g(-1) for Aroclor 1254 and 125 pg g(-1) for PCB-126. Estimated sample throughput for the SPLE-ELISA was about twice that of the stepwise extraction/cleanup needed for gas chromatography (GC) or GC/mass spectrometry (MS) detection. ELISA-derived uncorrected and corrected Aroclor 1254 levels correlated well (r=0.9973 and 0.9996) with the total Aroclor concentrations as measured by GC for samples from five different contaminated sites. ELISA-derived PCB-126 concentrations were higher than the sums of the 12 coplanar PCBs generated by GC/MS with a positive correlation (r=0.9441). Results indicate that the SPLE-ELISA approach can be used for quantitative or qualitative analysis of PCBs in soil and sediments. To our knowledge, this is the first report of an SPLE-ELISA approach not requiring a post-extraction cleanup step for detecting Aroclors and coplanar PCBs in soil and sediment.

Hybrid field-assisted solid-liquid-solid dispersive extraction for the determination of organochlorine pesticides in tobacco with gas chromatography

A novel one-step sample preparation technique termed hybrid field-assisted solid-liquid-solid dispersive extraction (HF-SLSDE) was developed in this study. A simple glass system equipped with a condenser was designed as an extraction vessel. The HF-SLSDE technique was a three-phase dispersive extraction approach. Target analytes were extracted from the sample into the extraction solvent enhanced by the hybrid field. Meanwhile, the interfering components were adsorbed by dispersing sorbent. No cleanup step preceded chromatographic analysis. The efficiency of the HF-SLSDE approach was demonstrated in the determination of organochlorine pesticide (OCP) residues in tobacco with a gas chromatography-electron capture detector (GC-ECD). Various operation conditions were studied systematically. Low detection limits (0.3-1.6 μg/kg) and low quantification limits (1.0-4.5 μg/kg) were achieved under the optimized conditions. The recoveries of OCPs ranged from 70.2% to 118.2%, with relative standard deviations of <9.6%, except for the lowest fortification level. Because of the effect of the hybrid field, HF-SLSDE showed significant predominance compared with other extraction techniques. The dispersing sorbent with good cleanup ability used in this study was also found to be a microwave absorption medium, which could heat the nonpolar extraction solvent under microwave irradiation. Different microstructures of tobacco samples before and after extractions demonstrated the mechanism of HF-SLSDE was based on an explosion at the cell level. According to the results, HF-SLSDE was proved to be a simple and effective sample preparation method for the analysis of pesticide residues in solid samples and could potentially be extended to other nonpolar target analytes in a complex matrix.