New method for development of carbon clad silica phases for liquid chromatography: Part I. Preparation of carbon phases

Improved synthesis of carbon-clad silica stationary phases

Previously, we described a novel method for cladding elemental carbon onto the surface of catalytically activated silica by a chemical vapor deposition (CVD) method using hexane as the carbon source and its use as a substitute for carbon-clad zirconia.1,2 In that method, we showed that very close to exactly one uniform monolayer of Al (III) was deposited on the silica by a process analogous to precipitation from homogeneous solution in order to preclude pore blockage. The purpose of the Al(III) monolayer is to activate the surface for subsequent CVD of carbon. In this work, we present an improved procedure for preparing the carbon-clad silica (denoted CCSi) phases along with a new column packing process. The new method yields CCSi phases having better efficiency, peak symmetry, and higher retentivity compared to carbon-clad zirconia. The enhancements were achieved by modifying the original procedure in three ways: First, the kinetics of the deposition of Al(III) were more stringently controlled. Second, the CVD chamber was flushed with a mixture of hydrogen and nitrogen gas during the carbon cladding process to minimize generation of polar sites by oxygen incorporation. Third, the fine particles generated during the CVD process were exhaustively removed by flotation in an appropriate solvent.

Development of a carbon clad core-shell silica for high speed two-dimensional liquid chromatography

We recently introduced a new method to deposit carbon on fully porous silicas (5 μm) to address some of the shortcomings of carbon clad zirconia (C/ZrO(2)), which has rather low retention due to its low surface area (20-30 m(2)/g). The method enables the introduction of a thin, homogeneous layer of Al(III) on silica to serve as catalytic sites for carbon deposition without damaging the silica's native pore structure. Subsequent carbon deposition by chemical vapor deposition resulted in chromatographically useful carbon phases as shown by good efficiencies and higher retentivity relative to C/ZrO(2). Herein, we use the above method to develop a novel carbon phase on superficially porous silica (2.7 μm). This small, new form of silica offers better mass transfer properties and higher efficiency with lower column back pressures as compared to sub 2 μm silica packings, which should make it attractive for use as the second dimension in fast two-dimensional LC (LC × LC). After carbon deposition, several studies were conducted to compare the new packing with C/ZrO(2). Consistent with work on 5 μm fully porous silica, the metal cladding did not cause pore blockage. Subsequent carbon deposition maintained the good mass transfer properties as shown by the effect of velocity on HETP. The new packing exhibits efficiencies up to ∼5.6-fold higher than C/ZrO(2) for polar compounds. We observed similar chromatographic selectivity for all carbon phases tested. Consequently, the use of the new packing as the second dimension in fast LC×LC improved the peak capacity of fast LC × LC. The new material gave loading capacities similar to C/ZrO(2), which is rather as expected based on the surface areas of the two phases.

Effect of first dimension phase selectivity in online comprehensive two dimensional liquid chromatography (LC×LC)

In this study, we examined the effect of first dimension column selectivity in reversed phase (RP) online comprehensive two dimensional liquid chromatography (LC×LC). The second dimension was always a carbon clad metal oxide reversed phase material. The hydrophobic subtraction model (HSM) and the related phase selective triangles were used to guide the selection of six different RP first dimension columns. Various kinds of samples were investigated and thus two different elution conditions were needed to cause full elution from the first dimension columns. We compared LC×LC chromatograms, contours plots, and fcoverage plots by measuring peak capacities, peak numbers, relative spatial coverage, correlation values, etc. The major finding of this study is that the carbon phase due to its rather different selectivity from other reversed phases is reasonably orthogonal to a variety of common types of bonded reversed phases. Thus quite surprisingly the six different first dimension stationary phases all showed generally similar separation patterns when paired to the second dimension carbon phase. This result greatly simplifies the task of choosing the correct pair of phases for RP×RP.