Dispersive liquid–liquid microextraction using non-chlorinated, lighter than water solvents for gas chromatography–mass spectrometry determination of fungicides in wine

Hydrophobic Eutectic Solvent-Based Dispersive Liquid-Liquid Microextraction Applied to the Analysis of Pesticides in Wine

A green solvent-based DLLME/HPLC-MS method for the determination of 19 pesticides in wine samples has been developed. The extractant solvent is a hydrophobic eutectic mixture composed of L-menthol and butylated hydroxytoluene in a molar ratio of 3:1. The endogenous ethanol of wine has been used as dispersive solvent, in order to avoid the solidification of the extracts under 19 °C. The mobile phase composition, the elution gradient and the sample injection volume were optimized in order to make this hydrophobic mixture compatible with conventional reversed phase chromatography and electrospray ionization. The method was validated in matrix, using a wine free from the target compounds. Average recovery as high as 80%, precision between 3 and 14%, and limits of detection and quantification much lower than the maximum residue levels (MRLs) for grapes and wines fixed by the EU regulation, make this multiresidue method fitted for the purpose, with the further advantages of being quick, cheap and in compliance with the green analytical chemistry. From the analysis of 11 commercial wines it was found that just in a bio sample the target compounds were not detectable or lower than quantification limit; as for the other samples, the most widespread and abundant pesticides were methoxyfenozide and boscalid, but their levels were much lower than the relative MRLs.

Utilizing a Rapid Multi-Plug Filtration Cleanup Method for 72 Pesticide Residues in Grape Wines Followed by Detection with Gas Chromatography Tandem Mass Spectrometry

A convenient and fast multi-residue method for the efficient identification and quantification of 72 pesticides belonging to different chemical classes in red and white grape wines has been developed. The analysis was based on gas chromatography tandem quadrupole mass spectrometric determination (GC-MS/MS). The optimization strategy involved the selection of the amount of multi-walled carbon nanotubes (MWCNTs) and the number of cleanup procedure cycles for multi-plug filtration cleanup (m-PFC) to achieve ideal recoveries and reduce the sample matrix compounds in the final extracts. The optimized procedure obtained consistent recoveries between 70.2 and 108.8% (70.2 and 108.8% for white wine, and 72.3 and 108.4% for red wine), with relative standard deviations (RSDs) that were generally lower than 9.2% at the three spiking levels of 0.01, 0.05 and 0.1 mg/kg. The linearity was studied in the range between 0.002 and 0.1 mg/kg using pesticide standards prepared both in pure solvent and in the presence of the matrix, showing coefficients of determination (R²) higher than 0.9495 for all the pesticides. To improve accuracy, matrix-matched calibration curves were used for calculating the quantification results. Finally, the method was used successfully for detecting pesticide residues in commercial grape wines.

Multiresidue Analytical Method for Pesticides in Soybean Extract

Developed and validated a fast, simple and effective method based on the use of DLLME technique and determination by GC-MS of 26 pesticides in SE. To carry out the extraction of the pesticides of the matrix, 70 μL of mix of pesticides (1.5 μg/mL) was added to 5.0 mL of SE, containing 1.0 g of sodium chloride and 3.0 mL of acetonitrile. The results of validation were suitable. The calibration curve was linear in the range of 0.500-5.0 μg/mL. The method showed a limit of detection and quantification of 0.17 μg/mL and 0.50 μg/mL, respectively. The recovery recovering between 47% and 115%, with relative standard deviation (RSD) of <20% for fortification levels (range of 1.0-3.0 μg/mL). The method validated can be applied for routine analysis in soy-based drinks, considering it is fast, easy to perform and has satisfactory validation results.

Simultaneous determination of melatonin and trans-resveratrol in wine by dispersive liquid-liquid microextraction followed by HPLC-FLD

The discovery of melatonin (Mel) in wines triggered a new interest in the paradigm of health benefits and wine consumption, usually ascribed to trans-resveratrol (trans-RSV). In this context, a dispersive liquid-liquid microextraction for the analysis of Mel and trans-RSV in wines by LC-FLD was developed. A 2^6-1 factorial design was used to identify the significant variables (p < 0.05) and Central Composite Design was used to achieve the optimal conditions: 300 µL of chloroform (extracting solvent), 1500 µL of acetonitrile (disperser solvent) and 1500 mg of NaCl (ionic strength). Excellent linearity (R² > 0.9999), repeatability (<3.55%), and accuracy (<7.18%) were obtained using a blank matrix and recoveries (>91.9%) using wines. The method was successfully applied to the analyses of Mel (0.63-7.44 ng mL^-1) and trans-RSV (169-2616 ng mL^-1) in different wine varieties. Comparison with literature point the overall advantages of the new method.

A sensitive pyrimethanil sensor based on porous NiCo2S4/graphitized carbon nanofiber film

With the extensive use of pesticides, the problem of pesticide residues has become people's concern. In this work, NiCo₂S₄ nanoneedle arrays grown on an electrospun graphitized carbon nanofiber film (NiCo₂S₄/GCNF) is successfully prepared by a simple two-step hydrothermal method, and further applied to detection of fungicide pyrimethanil (PMT). NiCo₂S₄ arrays exhibit a unique core-shell structure with rough surface, providing abundant electrochemically active sites exposed to the electrolyte. The NiCo₂S₄/GCNF modified electrode displays excellent electrocatalytic activity, and the electrode surface is controlled both by diffusion and adsorption processes. When applied to PMT determination, NiCo₂S₄/GCNF sensor displays wide linear range from 0.06 to 800 μM with low detection limit (20 nM). Furthermore, the as-proposed sensor also displays other outstanding advantages, including simple preparation, low cost, perfect reproducibility and good application in practical samples. Such attracting analytical properties could be attributed to high electrocatalytic activity of NiCo₂S₄ and superior electrical conductivity of GCNF frameworks. In addition, the detailed oxidation mechanism of PMT at NiCo₂S₄/GCNF electrode was also studied. The results indicate that NiCo₂S₄/GCNF is a promising platform for PMT sensors.

A Vortex-Assisted Dispersive Liquid-Liquid Microextraction Followed by UPLC-MS/MS for Simultaneous Determination of Pesticides and Aflatoxins in Herbal Tea

A method for detecting the organophosphorus pesticides residue and aflatoxins in China herbal tea has been developed by UPLC-MS/MS coupled with vortex-assisted dispersive liquid-liquid microextraction (DLLME). The extraction conditions for vortex-assisted DLLME extraction were optimized using single-factor experiments and response surface design. The optimum conditions for the experiment were the pH 5.1, 347 µL of chloroform (extraction solvent) and 1614 µL of acetonitrile (dispersive solvent). Under the optimum conditions, the targets were good linearity in the range of 0.1 µg/L⁻25 µg/L and the correlation coefficient above 0.9998. The mean recoveries of all analytes were in the ranged from 70.06%⁻115.65% with RSDs below 8.54%. The detection limits were in the range of 0.001 µg/L⁻0.01µg/L. The proposed method is a fast and effective sample preparation with good enrichment and extraction efficiency, which can simultaneously detect pesticides and aflatoxins in China herbal tea.

A class-selective immunoassay for simultaneous analysis of anilinopyrimidine fungicides using a rationally designed hapten

The development of multianalyte immunoassays constitutes a main research issue in the field of bioanalytical techniques. In the present study, class-specific antibodies against the three members of the anilinopyrimidine family of fungicides (pyrimethanil, cyprodinil and mepanipyrim) were raised by using a bioconjugate of a rationally designed hapten [5-(6-methyl-2-(phenylamino)pyrimidin-4-yl)pentanoic acid]. Highly sensitive immunoassays were developed for the generic determination of these compounds, using the competitive enzyme-linked immunosorbent assay (ELISA). Particularly, a direct antibody-coated competitive ELISA afforded identical sensitivity for the three anilinopyrimidines, with IC₅₀ values of 0.26, 0.27 and 0.25 μg L^-1 for pyrimethanil, cyprodinil and mepanipyrim, respectively. This immunoassay was fully characterized and applied to the multianalyte determination of anilinopyrimidine fungicides in white and red wines, with a limit of quantification of 1 μg L^-1, average recoveries from 93.1 to 114.4%, and relative standard deviations lower than 20%. Commercial wine samples were analyzed and those containing detectable anilinopyrimide residues were verified by a reference chromatographic technique.

Simultaneous Determination and Investigation of Nine Fungicides in Fruits Using Diethylenetriamine-Functional Magnetic Core-Shell Polymer Modified Graphene Oxide as an Efficient Adsorbent Coupled to UPLC-HRMS

In this study, diethylenetriamine-functional magnetic core-shell polymer modified graphene oxide (DETA-MPs-GO) was prepared via precipitation polymerization and amidation reaction, and it was characterized by transmission electron microscopy (TEM), Fourier-transformed infrared spectroscopy (FTIR), and X-ray diffractometer (XRD). Subsequently, a magnetic solid-phase extraction (MSPE) procedure was applied to the as-synthesized DETA-MPs-GO for the detection of nine fungicides in fruit samples, prior to ultra-performance liquid chromatography-high resolution mass spectrometry (UPLC-HRMS). The homogenized fruit samples, spiked with D-labelled internal standards, were firstly extracted by 5 mL of acetonitrile twice and then purified by DETA-MPs-GO adsorbents. The optimization of the adsorption and elution conditions of DETA-MPs-GO toward fungicides was carried out to attain a satisfactory adsorption performance and desorption efficiency. The adsorption mechanism was carefully investigated, and the results revealed that a synergistic adsorption mechanism, including hydrogen bond and a π-π stacking interaction, was confirmed. Moreover, the limits of quantitation (LOQs) of the proposed approach were in the range of 0.01 to 0.30 μg/kg under the optimum conditions. The average recoveries at three spiking levels were 84.9% to 105.2%, with relative standard deviations (RSDs) varying from 0.8% to 8.2% (n = 6). The developed method was successfully utilized for the screening and detection of fungicides in 81 fruit samples purchased from markets. A detailed survey was carried out about the concentration distribution, types of fungicides, and combined use of fungicides in different fruits.

Simultaneous determination of boscalid and fludioxonil in grape and soil under field conditions by gas chromatography/tandem triple quadrupole mass spectrometry

A gas chromatography-tandem mass spectrometry method was developed and validated to simultaneously determine boscalid and fludioxonil in grape and soil samples. These samples were extracted with 10 mL of acetonitrile and purified using a mixed primary secondary amine/octadecylsilane sorbent. The method showed good linearity (R²  > 0.99) in the calibration range 0.005-2 μg/mL for both pesticides. The limits of detection and quantification for the two analytes in grape and soil were 0.006 and 0.02 mg/kg, respectively. Fungicide recoveries in grape and soil were 81.18-92.11% for boscalid and 82.73-97.67% for fludioxonil with relative standard deviations of 1.31-10.31%. The established method was successfully applied to the residual analysis of boscalid and fludioxonil in real grape and soil samples. The terminal residue concentrations of boscalid and fludioxonil in grape samples collected from Anhui and Guizhou were <5 mg/kg (the maximum residue limit set by China) 7 days after the last application and 1 mg/kg (the maximum residue limit set by USA) 14 days after the last application. These results could provide guidance for the proper and safe use of boscalid and fludioxonil in grape and help the Chinese government to establish an MRL for fludioxonil in grape.

Covalent Bonding of Metal-Organic Framework-5/Graphene Oxide Hybrid Composite to Stainless Steel Fiber for Solid-Phase Microextraction of Triazole Fungicides from Fruit and Vegetable Samples

A hybrid material of the zinc-based metal-organic framework-5 and graphene oxide (metal-organic framework-5/graphene oxide) was prepared as a novel fiber coating material for solid-phase microextraction (SPME). The SPME fibers were fabricated by covalent bonding via chemical cross-linking between the coating material metal-organic framework-5/graphene oxide and stainless steel wire. The prepared fiber was used for the extraction of five triazole fungicides from fruit and vegetable samples. Gas chromatography coupled with microelectron capture detector (GC-μECD) was used for quantification. The developed method gave a low limit of detection (0.05-1.58 ng g(-1)) and good linearity (0.17-100 ng g(-1)) for the determination of the triazole fungicides in fruit and vegetable samples. The relative standard deviations (RSDs) for five replicate extractions of the triazole fungicides ranged from 3.7 to 8.9%. The method recoveries for spiked fungicides (5, 20, and 50 ng g(-1)) in grape, apple, cucumber, celery cabbage, pear, cabbage, and tomato samples were in the range of 85.6-105.8% with the RSDs ranging from 3.6 to 11.4%, respectively, depending on both the analytes and samples. The metal-organic framework-5/graphene oxide coated fiber was stable enough for 120 extraction cycles without a significant loss of extraction efficiency. The method was suitable for the determination of triazole fungicides in fruit and vegetable samples.

Use of magnetic effervescent tablet-assisted ionic liquid dispersive liquid-liquid microextraction to extract fungicides from environmental waters with the aid of experimental design methodology

In this work, a novel effervescence-assisted microextraction technique was proposed for the detection of four fungicides. This method combines ionic liquid-based dispersive liquid-liquid microextraction with the magnetic retrieval of the extractant. A magnetic effervescent tablet composed of Fe3O4 magnetic nanoparticles, sodium carbonate, sodium dihydrogen phosphate and 1-hexyl-3-methylimidazolium bis(trifluoromethanesulfonimide) was used for extractant dispersion and retrieval. The main factors affecting the extraction efficiency were screened by a Plackett-Burman design and optimized by a central composite design. Under the optimum conditions, good linearity was obtained for all analytes in pure water model and real water samples. Just for the pure water, the recoveries were between 84.6% and 112.8%, the limits of detection were between 0.02 and 0.10 μg L(-1) and the intra-day precision and inter-day precision both are lower than 4.9%. This optimized method was successfully applied in the analysis of four fungicides (azoxystrobin, triazolone, cyprodinil, trifloxystrobin) in environmental water samples and the recoveries ranged between 70.7% and 105%. The procedure promising to be a time-saving, environmentally friendly, and efficient field sampling technique.

Up-and-down-shaker-assisted dispersive liquid-liquid microextraction coupled with gas chromatography-mass spectrometry for the determination of fungicides in wine

An up-and-down-shaker-assisted dispersive liquid-liquid microextraction (UDSA-DLLME) method coupled with gas chromatography-mass spectrometry was developed for the determination of fungicides (cyprodinil, procymidone, fludioxonil, flusilazole, benalaxyl, and tebuconazole) in wine. The developed method requires 11 μL of 1-octanol without the need for dispersive solvents. The total extraction time was approximately 3 min. Under optimum conditions, the linear range of the method was 0.05-100 μg L(-1) for all fungicides and the limit of detection was 0.007-0.025 μg L(-1). The absolute and relative recoveries were 31-83% and 83-107% for white wine, respectively, and 32-85% and 83-108% for red wine, respectively. The intra-day and inter-day precision were 0.5-7.5% and 0.7-6.1%, respectively. Our developed method had good sensitivity and high extraction efficiency. UDSA-DLLME is a desirable method in terms of performance and speed.

Water with low concentration of surfactant in dispersed solvent-assisted emulsion dispersive liquid-liquid microextraction for the determination of fungicides in wine

A sample preparation method, dispersive liquid-liquid microextraction assisted by an emulsion with low concentration of a surfactant in water and dispersed solvent coupled with gas chromatography-mass spectrometry, was developed for the analysis of the fungicides cyprodinil, procymidone, fludioxonil, flusilazole, benalaxyl, and tebuconazole in wine. A microsyringe was used to withdraw and discharge a mixture of extraction solvent and 240 μL of an aqueous solution of Triton X-100 (the dispersed agent) four times within 10 s to form a cloudy emulsion in the syringe. This emulsion was then injected into a 5 mL wine sample spiked with all of the above fungicides. The total extraction time was approximately 0.5 min. Under optimum conditions using 1-octanol (12 μL) as extraction solvent, the linear range of the method in analysis of all six fungicides was 0.05-100 μg L(-1), and the limit of detection ranged from 0.013 to 0.155 μg L(-1). The absolute recoveries (n = 3) and relative recoveries (n = 3) were 30-83 and 81-108% for white wine at 0.5, 5, and 5 μg L(-1), and 30-92 and 81-110% for red wine, respectively. The intraday (n = 7) and interday (n = 6) relative standard deviations ranged from 4.4 to 8.8% and from 4.3 to 11.2% at 0.5 μg L(-1), respectively. The method achieved high enrichment factors. It is an alternative sample preparation technique with good performance.

A simple solvent collection technique for a dispersive liquid-liquid microextraction of parabens from aqueous samples using low-density organic solvent

A simple technique for the collection of an extraction solvent lighter than water after dispersive liquid-liquid microextraction combined with high-performance liquid chromatography with ultraviolet detection was developed for the determination of four paraben preservatives in aqueous samples. After the extraction procedure, low-density organic solvent together with some little aqueous phase was separated by using a disposable glass Pasteur pipette. Next, the flow of the aqueous phase was stopped by successive dipping the capillary tip of the pipette into anhydrous Na(2)SO(4). The upper organic layer was then removed simply with a microsyringe and injected into the high-performance liquid chromatography system. Experimental parameters that affect the extraction efficiency were investigated and optimized. Under optimal extraction conditions, the extraction recoveries ranged from 25 to 86%. Good linearity with coefficients with the square of correlation coefficients ranging from 0.9984 to 0.9998 was observed in the concentration range of 0.001-0.5 μg/mL. The relative standard deviations ranged from 4.1 to 9.3% (n = 5) for all compounds. The limits of detection ranged from 0.021 to 0.046 ng/mL. The method was successfully applied for the determination of parabens in tap water and fruit juice samples and good recoveries (61-108%) were achieved for spiked samples.

Determination of pesticide residues in wine by membrane-assisted solvent extraction and high-performance liquid chromatography-tandem mass spectrometry

The determination of pesticides in food products is an essential issue to guarantee food safety and minimise health risks of consumers. A protocol based on membrane-assisted solvent extraction and liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) that allows the determination of 18 pesticides in red wine at minimum labour effort for sample preparation was developed and validated. Ten millilitres of wine were extracted using 100 μL of toluene filled in a non-porous polyethylene membrane bag which is immersed in the wine sample. After 150 min extraction under stirring, an aliquot of the extraction solution is analysed using HPLC-MS/MS. The limits of quantification ranged from 3 ng/L for Pirimicarb to 1.33 μg/L for Imidacloprid. Quantification by matrix-matched calibration provided relative standard deviations ≤16 % for most of the target pesticides. The linearity of calibration was given over three to four orders of magnitude, which enables the reliable measurement of a broad range of pesticide concentrations, and for each target pesticide, the sensitivity of the protocol meets the maximum residue levels set by legislations at least for wine grapes. Good agreement of results was found when the new method was compared with a standard liquid-liquid extraction protocol. In five wine samples analysed, Carbendazim and Metalaxyl were determined at micrograms per litre concentrations, even in some of the organic wines. Tebuconazol and Cyprodinitril were determined at lower abundance and concentration, followed by Spiroxamin and Diuron.