Electrodeposition of gold nanoparticles onto an etched stainless steel wire followed by a self-assembled monolayer of octanedithiol as a fiber coating for selective solid-phase microextraction

Development and characterization of self-powered, highly sensitive optoelectronic device based on PVA-rGO nanofibers/n-Si

This study provided a promising way to fabricate low-cost and high-performance Poly (vinyl alcohol)-reduced graphene oxide (PVA-RGO) nanofibers/n-Si heterojunction photodetector. For this purpose, the hybrid heterojunction with a very-high rectification ratio (2.4 × 106) was achieved by successfully coating PVA-RGO nanofibers on n-Si wafer by electrospinning method. When the electro-optical analysis of the fabricated heterojunction photodetector under visible light depending on the light intensity, ultraviolet (UV) and infrared (IR) lights was examined in detail, it was observed that the photodetector exhibited both self-powered behavior and very high photo-response under each light sources. However, the highest optical performance was obtained under UV (365 nm) originated from PVA-RGO layer and IR (850 nm) light from both interfacial states between PVA-RGO nanofibers and Si and from Si layer. Under 365 nm UV light, the maximum performance values of R, D, ON/OFF ratio, normalized photo-dark-current ratio and external quantum efficiency (%) were obtained as 688 mA W-1, 1.15 × 1015Jones, 2.49 × 106, 8.28 × 1010W-1and 234%, respectively.

Review: Microextraction Technique Based New Trends in Food Analysis

Food chemistry is the study and classification of the quality and origin of foods. The identification of definite biomarkers and the determination of residue contaminants such as toxins, pesticides, metals, human and veterinary drugs, which are a very common source of food-borne diseases. The food analysis is continuously demanding the improvement of more robust, sensitive, highly efficient, and economically beneficial analytical approaches to promise the traceability, safety, and quality of foods in the acquiescence with the consumers and legislation demands. The traditional methods have been used at the starting of the 20th century based on wet chemical methods. Now it existing the powerful analytical techniques used in food analysis and safety. This development has led to substantial enhancements in the analytical accuracy, precision, sensitivity, selectivity, thereby mounting the applied range of food applications. In the present decade, microextraction (micro-scale extraction) pays more attention due to its futures such as low consumption of solvent and sample, throughput analysis easy to operate, greener, robotics, and miniaturization, different adsorbents have been used in the microextraction process with unique nature recognized with wide range applications.

Use of Nanomaterial-Based (Micro)Extraction Techniques for the Determination of Cosmetic-Related Compounds

The high consumer demand for cosmetic products has caused the authorities and the industry to require rigorous analytical controls to assure their safety and efficacy. Thus, the determination of prohibited compounds that could be present at trace level due to unintended causes is increasingly important. Furthermore, some cosmetic ingredients can be percutaneously absorbed, further metabolized and eventually excreted or bioaccumulated. Either the parent compound and/or their metabolites can cause adverse health effects even at trace level. Moreover, due to the increasing use of cosmetics, some of their ingredients have reached the environment, where they are accumulated causing harmful effects in the flora and fauna at trace levels. To this regard, the development of sensitive analytical methods to determine these cosmetic-related compounds either for cosmetic control, for percutaneous absorption studies or for environmental surveillance monitoring is of high interest. In this sense, (micro)extraction techniques based on nanomaterials as extraction phase have attracted attention during the last years, since they allow to reach the desired selectivity. The aim of this review is to provide a compilation of those nanomaterial-based (micro)extraction techniques for the determination of cosmetic-related compounds in cosmetic, biological and/or environmental samples spanning from the first attempt in 2010 to the present.

Combining microextraction methods with surface-enhanced Raman spectroscopy towards more selective and sensitive analyte detection by plasmonic metal nanoparticles

Raman signals of analytes can be enhanced on the surface of noble nanoparticles by generating SERS signals, which can be further enhanced using microextraction (ME) techniques.

Recent Applications and Newly Developed Strategies of Solid-Phase Microextraction in Contaminant Analysis: Through the Environment to Humans

The present review aims to describe the recent and most impactful applications in pollutant analysis using solid-phase microextraction (SPME) technology in environmental, food, and bio-clinical analysis. The covered papers were published in the last 5 years (2014–2019) thus providing the reader with information about the current state-of-the-art and the future potential directions of the research in pollutant monitoring using SPME. To this end, we revised the studies focused on the investigation of persistent organic pollutants (POPs), pesticides, and emerging pollutants (EPs) including personal care products (PPCPs), in different environmental, food, and bio-clinical matrices. We especially emphasized the role that SPME is having in contaminant surveys following the path that goes from the environment to humans passing through the food web. Besides, this review covers the last technological developments encompassing the use of novel extraction coatings (e.g., metal-organic frameworks, covalent organic frameworks, PDMS-overcoated fiber), geometries (e.g., Arrow-SPME, multiple monolithic fiber-SPME), approaches (e.g., vacuum and cold fiber SPME), and on-site devices. The applications of SPME hyphenated with ambient mass spectrometry have also been described.

Three-dimensional Pd/Pt bimetallic nanodendrites on a highly porous copper foam fiber for headspace solid-phase microextraction of BTEX prior to their quantification by GC-FID

The preparation of bimetallic Pd/Pt nanofoam for use in fiber based solid-phase microextraction (SPME) is described. First, a highly porous copper foam was prepared on the surface of an unbreakable copper wire by an electrochemical method. Then, the substrate was covered with metallic Pd and Pt using galvanic replacement of the Cu nanofoam substrate by applying a mixture of Pd(II) and Pt(IV) ions. The procedure provided an efficient route to modify Pd/Pt nanofoams with large specific surface and low loading with expensive noble metals. The fiber was applied to headspace SPME of benzene, toluene, ethylbenzene and xylene (BTEX) (as the model compounds) in various spiked water and wastewater samples. It was followed by gas chromatography-flame ionization detection (GC-FID). A Plackett-Burman design was performed for screening the experimental factors prior to Box-Behnken design. Compared with the commercial PDMS SPME fiber (100 μm), it had higher extraction efficiency for BTEX. Under the optimum conditions, the method has low limits of detection (0.16-0.35 μg L^-1), a wide linear range (1-200 μg L^-1), relative standard deviations between 5.8 and 10.5%, and good recoveries (>85% from spiked samples). Graphical abstract Schematic presentation of a three-dimensional Pd/Pt bimetallic nanodendrites supported on a highly porous copper foam fiber for use in headspace solid phase microextraction of BTEX. They were then quantified by gas chromatography-flame ionization detector.

Combining Headspace Solid-Phase Microextraction and Surface-Enhanced Raman Spectroscopy To Detect the Pesticide Fonofos in Apple Juice

We developed an innovative approach that couples headspace solid-phase microextraction (SPME) with surface-enhanced Raman spectroscopy (SERS) to detect a volatile pesticide (i.e., fonofos) in a liquid complex matrix (i.e., apple juice). A gold nanoparticles-coated fiber was fabricated by reducing gold(III) on a chemically etched stainless steel wire to extract pesticide, using SPME. The fabricated fibers were then tested by a headspace-SPME method and a dip-SPME method, followed by SERS detection of fonofos in water and apple juice samples. Using the headspace-SPME method, we can detect as low as 5 ppb of fonofos in water and apple juice, compared with the dip-SPME method, which cannot detect lower than 10 ppb in water and 50 ppb in apple juice. This study demonstrated the potential capability of the headspace-SPME-SERS method for rapid (within 30 min) and sensitive detection of volatile and vaporizable compounds in complex matrices. The developed method could be a potential alternative approach to the gas chromatography method. Future work is needed to optimize the fiber by minimizing signal variation, and it should be tested in a variety of targeted compounds and matrices.

Electrodeposition of self-assembled poly(3,4-ethylenedioxythiophene) @gold nanoparticles on stainless steel wires for the headspace solid-phase microextraction and gas chromatographic determination of several polycyclic aromatic hydrocarbons

In this work, a novel poly(3,4-ethylenedioxythiophene)@Au nanoparticles (PEDOT@AuNPs) hybrid coating was prepared and characterized. Firstly, the monomer 3,4-ethylenedioxythiophene was self-assembled on AuNPs, and then electropolymerization was performed on a stainless steel wire by cyclic voltammetry. The obtained PEDOT@AuNPs coating was rough and showed cauliflower-like micro-structure with thickness of ∼40μm. It displayed high thermal stability (up to 330°C) and mechanical stability and could be used for at least 160 times of solid phase microextraction (SPME) without decrease of extraction performance. The coating exhibited high extraction capacity for some environmental pollutants (e.g. naphthalene, 2-methylnaphthalene, acenaphthene, fluorene and phenathrene) due to the hydrophobic interaction between the analytes and PEDOT and the additional physicochemical affinity between polycyclic aromatic hydrocarbons and AuNPs. Through coupling with GC detection, good linearity (correlation coefficients higher than 0.9894), wide linear range (0.01-100μgL^-1), low limits of detection (2.5-25ngL^-1) were achieved for these analytes. The reproducibility (defined as RSD) was 1.1-4.0% and 5.8-9.9% for single fiber (n=5) and fiber-to-fiber (n=5), respectively. The SPME-GC method was successfully applied for the determination of three real samples, and the recoveries for standards added were 89.9-106% for lake water, 95.7-112% for rain water and 93.2-109% for soil saturated water, respectively.

Hydrothermally grown and self-assembled modified titanium and nickel oxide composite nanosheets on Nitinol-based fibers for efficient solid phase microextraction

A novel titanium and nickel oxide composite nanosheets (TiO₂/NiOCNSs) coating was in situ grown on a Nitinol (NiTi) wire by direct hydrothermal treatment and modified by self-assembly of trichlorophenylsilane for solid phase microextraction (SPME). TiO₂/NiOCNSs were radially oriented and chemically bonded to the NiTi substrate with double-faced open access sites. Moreover the phenyl modified TiO₂/NiOCNSs (TiO₂/NiOCNSs-Ph) coating exhibited original surface supporting framework favorable for effective SPME. The extraction performance of TiO₂/NiOCNSs-Ph coated NiTi (NiTi-TiO₂/NiOCNSs-Ph) fiber was investigated for the concentration and detection of ultraviolet (UV) filters, polycyclic aromatic hydrocarbons (PAHs), phthalate acid esters and polychlorinated biphenyls coupled to HPLC with UV detection. The novel fiber exhibited better selectivity for UV filters and PAHs and presented greater extraction capability compared to commercial polydimethylsiloxane and polyacrylate fibers. Under the optimized conditions for SPME of UV filters, the proposed method presented linear ranges from 0.1 to 300μg/L with correlation coefficients of higher than 0.999 and limits of detection from 0.030μg/L to 0.064μg/L. Relative standard deviations (RSDs) were below 7.16% and 8.42% for intra-day and inter-day measurements with the single fiber, respectively. Furthermore RSDs for fiber-to-fiber reproducibility from 6.57% to 8.93% were achieved. The NiTi-TiO₂/NiOCNSs-Ph fiber can be used up to 200 times. The proposed method was successfully applied to the preconcentration and determination of trace target UV filters in different environmental water samples. The relative recoveries from 87.3% to 104% were obtained with RSDs less than 8.7%.

A novel Schiff base network-1 nanocomposite coated fiber for solid-phase microextraction of phenols from honey samples

A novel covalent organic framework, Schiff base network-1 (SNW-1), was synthesized and used as a solid-phase microextraction (SPME) fiber coating material. The SNW-1 coated SPME fiber was fabricated by a covalent chemical cross-linking between the SNW-1 nanocomposite and a silanol-functionalized stainless steel wire substrate. Scanning electron microscopy and nitrogen isothermal adsorption results indicate that the new fiber coating exhibited a porous, homogenous surface with the Brunauer-Emmett-Teller surface of 668m²g^-1. The prepared fiber was explored for the SPME of phenols from honey samples prior to their determination by gas chromatography-mass spectrometry. The developed method had large enrichment factors (136-816), low limits of detection (0.06-0.2ngg^-1), good linearity (0.1-100.0ngg^-1) and repeatability (<9.7%) for phenols. The recoveries for spiked phenols (1.0ngg^-1 and 10.0ngg^-1) in Wolfberry, Robinia and Codonopsis honey samples were in the range of 84.2-107.2% with the relative standard deviations ranging from 3.8% to 12.7%. The developed method was suitable for the determination of phenols from honey samples.

Self-assembly of alkyldithiols on a novel dendritic silver nanostructure electrodeposited on a stainless steel wire as a fiber coating for solid-phase microextraction

A facile and efficient electrodeposition approach for the controllable preparation of dendritic silver nanostructure was developed on an etched stainless steel (ESS) wire.