Faster dispersive liquid-liquid microextraction methods using magnetic ionic liquids as solvents

Investigating a new approach for magnetic ionic liquids: Dispersive liquid-liquid microextraction coupled to pyrolysis gas-chromatography-mass spectrometry to determine flame retardants in sewage sludge samples

This study addresses the analysis of emerging contaminants, often using chromatographic techniques coupled to mass spectrometry. However, sample preparation is often required prior to instrumental analysis, and dispersive liquid-liquid microextraction (DLLME) is a viable strategy in this context. DLLME stands out for its ability to reduce sample and solvent volumes. Notably, dispersive liquid-liquid microextraction using magnetic ionic liquids (MILs) has gained relevance due to the incorporation of paramagnetic components in the chemical structure, thereby eliminating the centrifugation step. A pyrolizer was selected in this work to introduce sample onto the GC column, since the MIL is extremely viscous and incompatible with direct introduction through an autosampler. This study is the first to report the use of a DLLME/MIL technique for sample introduction through a pyrolizer in gas chromatography coupled to mass spectrometry (GC-MS). This approach enables the MIL to be compatible with gas chromatography systems, resulting in optimized analytical and instrument performance. The analysis of polybrominated diphenyl ether flame retardants (PBDEs) was focused on the PBDE congeners 28, 47, 99, 100, and 153 in sewage sludge samples. The [P6,6,6,14+]2[MnCl42-] MIL was thoroughly characterized using UV-Vis, Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy, as well as thermal analysis. In the chromatographic method, a pyrolyzer was used in the sample introduction step (Py-GC-MS), and critical injection settings were optimized using multivariate approaches. Optimized conditions were achieved with a temperature of 220 °C, a pyrolysis time of 0.60 min, and an injection volume of 9.00 μL. DLLME optimization was performed through central compound planning (CCD), and optimized training conditions were achieved with 10.0 mg of MIL, 3.00 μL of acetonitrile (ACN) as dispersive solvent, extraction time of 60 s, and volume of a sample of 8.50 mL. Precision was observed to range from 0.11 % to 12.5 %, with limits of detection (LOD) of 44.4 μg L-1 for PBDE 28, 16.9 μg L-1 for PBDE 47 and PBDE 99, 33.0 μg L-1 for PBDE 100 and 375 μg L-1 for PBDE 153. PBDE 28 was identified and analyzed in the sludge sample at a concentration of 800 μg L-1. The use of MIL in dispersive liquid-liquid microextraction combined with pyrolysis gas chromatography-mass spectrometry enables identification and quantification of PBDEs in sewage sludge samples at concentrations down to the µg L-1 level.

Magnetic Ionic Liquids: Current Achievements and Future Perspectives with a Focus on Computational Approaches

Magnetic ionic liquids (MILs) stand out as a remarkable subclass of ionic liquids (ILs), combining the desirable features of traditional ILs with the unique ability to respond to external magnetic fields. The incorporation of paramagnetic species into their structures endows them with additional attractive features, including thermochromic behavior and luminescence. These exceptional properties position MILs as highly promising materials for diverse applications, such as gas capture, DNA extractions, and sensing technologies. The present Review synthesizes key experimental findings, offering insights into the structural, thermal, magnetic, and optical properties across various MIL families. Special emphasis is placed on unraveling the influence of different paramagnetic species on MILs' behavior and functionality. Additionally, the Review highlights recent advancements in computational approaches applied to MIL research. By leveraging molecular dynamics (MD) simulations and density functional theory (DFT) calculations, these computational techniques have provided invaluable insights into the underlying mechanisms governing MILs' behavior, facilitating accurate property predictions. In conclusion, this Review provides a comprehensive overview of the current state of research on MILs, showcasing their special properties and potential applications while highlighting the indispensable role of computational methods in unraveling the complexities of these intriguing materials. The Review concludes with a forward-looking perspective on the future directions of research in the field of magnetic ionic liquids.

Magnetic ionic liquid-based liquid-liquid microextraction followed by ultra-performance liquid chromatography coupled with triple-quadrupole tandem mass spectrometry for simultaneous determination of neurotransmitters in human cerebrospinal fluid and plasma

A green, efficient and easy sample pretreatment method of magnetic ionic liquid-based liquid-liquid microextraction (MIL-based LLME) combined with a sensitive, rapid and precise analytical method of ultra-performance liquid chromatography coupled with triple-quadrupole tandem mass spectrometry (UPLC-QqQ/MS²) was developed to simultaneously - determining of neurotransmitters (NTs) in biosamples. Two magnetic ionic liquids (MILs), [P_6,6,6,14]₃[GdCl₆] and [P_6,6,6,14]₂[CoCl₄] tested, and the latter was selected as the extraction solvent due to its advantages of visual recognition, paramagnetic behavior and higher extraction efficiency. Facile magnetic separation of MIL containing analytes from matrix was realized by applying external magnetic field without rather than centrifugation. Experimental parameters that would influence the extraction efficiency, including type and amount of MIL, extraction time, speed of the vortex process, salt concentration, and environmental pH, were optimized obtained. The proposed method was successfully applied to the simultaneous extraction and determination of 20 NTs in human cerebrospinal fluid and plasma samples. Excellent analytical performance indicates the broad potential of this method for clinical diagnosis and therapy of neurological diseases.

A Gadolinium-Based Magnetic Ionic Liquid for Dispersive Liquid–Liquid Microextraction of Ivermectin from Environmental Water

The recently introduced gadolinium-based magnetic ionic liquid (Gd-MIL) has been exploited as an extractant in dispersive liquid–liquid microextraction (DLLME) for preconcentration of ivermectin (IVR) from water samples followed by analysis using reversed-phase HPLC with UV detection at 245 nm. The utilized Gd-MIL extractant is hydrophobic with markedly high magnetic susceptibility. These features result in an efficient extraction of the lipophilic analyte and facilitate the phase separation under the influence of a strong magnetic field, thus promoting the method sensitivity and increasing the potential for automation. To maximize the IVR enrichment by DLLME, the procedure was optimized for extractant mass, dispersive solvent type/volume, salt addition and diluent pH. At optimized conditions, an enrichment factor approaching 70 was obtained with 4.0-mL sample sizes. The method was validated in terms of accuracy, precision, specificity and limit of quantitation. The method was successfully applied to the determination of IVR in river water samples with a mean relative recovery of 97.3% at a spiked concentration of 400 ng/mL. Compared with other reported methods, this approach used a simpler procedure with improved precision, lower amounts of safer solvents and a short analysis time.

Rapid removal of detergent in glycolipids using ionic liquids

Detergent removal in glycolipid after sample preparation, such as enzymatic reaction or isolation of detergent-resistant membrane microdomain, is indispensable for further structural characterization. We previously established the rapid and effective method of detergent removal in glycolipid samples from glass test tube using 1,2-dichloroethane (DCE) washing. However, the use of DCE has several drawbacks, such as environmental risks, harmful effects (potentially carcinogenic), and high vaporability and flammability. To solve the issue, we used ionic liquids to remove detergents from glycolipid samples, and found 1-butyl-3-methylimidazolium iodide was a suitable alternative for DCE.

An overview of magnetic ionic liquids: From synthetic strategies to applications in microextraction techniques

Remarkable progress has been achieved in the application of magnetic ionic liquids in microextraction-based procedures. These materials exhibit unique physicochemical properties of ionic liquids featuring additional responses to magnetic fields by incorporating a paramagnetic component within the chemical structure. This intriguing property can open new horizons in analytical extractions because the solvent manipulation is facilitated. Moreover, the tunable chemical structures of magnetic ionic liquids also allow for task-specific extractions that can significantly increase the method selectivity. This review aimed at providing an up-to-date overview of articles involving synthesis, physicochemical properties, and applications of magnetic ionic liquids highlighting recent developments and configurations. Moreover, a section containing critical evaluation and future trends in magnetic ionic liquid-based extractions is included.

Magnetic Ionic Liquids in Sample Preparation: Recent Advances and Future Trends

In the last decades, a myriad of materials has been synthesized and utilized for the development of sample preparation procedures. The use of their magnetic analogues has gained significant attention and many procedures have been developed using magnetic materials. In this context, the benefits of a new class of magnetic ionic liquids (MILs), as non-conventional solvents, have been reaped in sample preparation procedures. MILs combine the advantageous properties of ionic liquids along with the magnetic properties, creating an unsurpassed combination. Owing to their unique nature and inherent benefits, the number of published reports on sample preparation with MILs is increasing. This fact, along with the many different types of extraction procedures that are developed, suggests that this is a promising field of research. Advances in the field are achieved both by developing new MILs with better properties (showing either stronger response to external magnetic fields or tunable extractive properties) and by developing and/or combining methods, resulting in advanced ones. In this advancing field of research, a good understanding of the existing literature is needed. This review aims to provide a literature update on the current trends of MILs in different modes of sample preparation, along with the current limitations and the prospects of the field. The use of MILs in dispersive liquid–liquid microextraction, single drop microextraction, matrix solid-phase dispersion, etc., is discussed herein among others.

Polymeric metal-containing ionic liquid sorbent coating for the determination of amines using headspace solid-phase microextraction

This study describes the design, synthesis, and application of polymeric ionic liquid sorbent coatings featuring nickel metal centers for the determination of volatile and semivolatile amines from water samples using headspace solid-phase microextraction. The examined polymeric ionic liquid (PIL) sorbent coatings were composed of two ionic liquid monomers (tetra(3-vinylimidazolium)nickel bis[(trifluoromethyl)sulfonyl]imide [Ni²⁺ (VIM)₄ ] 2[NTf₂ ^- ] and 1-vinyl-3-hexylimidazolium [HVIM⁺ ][NTf₂ ^- ]), and an ionic liquid cross-linker (1,12-di(3-vinylimidazolium)dodecane  [(VIM)₂ C₁₂ ²⁺ ] 2[NTf₂ ^- ]). With these ionic liquid monomers and cross-linkers, three different types of coatings were prepared: PIL 1 based on the neat [Ni²⁺ (VIM)₄ ] 2[NTf₂ ^- ] monomer, PIL 2 consisting of the [Ni²⁺ (VIM)₄ ] 2[NTf₂ ^- ] monomer with addition of cross-linker, and PIL 3 composed of the [HVIM⁺ ][NTf₂ ^- ] monomer and cross-linker. Analytical performance of the prepared sorbent coatings using headspace solid-phase microextraction gas chromatography-mass spectrometry was compared with the polydimethylsiloxane and polyacrylate commercial coatings. The PIL 2 sorbent coating yielded the highest enrichment factors ranging from 5500 to over 160 000 for the target analytes. The developed headspace solid-phase microextraction gas chromatography-mass spectrometry method was applied for the analysis of real samples (the concentration of amines was 200 μg/L), producing relative recovery values in the range of 90.9-120.0% (PIL 1) and 83.0-122.7% (PIL 2) from tap water, and 84.8-112.4% (PIL 1) and 79.2-119.3% (PIL 2) from lake water.

Ultra-sensitive Sb speciation analysis in water samples by magnetic ionic liquid dispersive liquid-liquid microextraction and multivariate optimization

Efficient separation and preconcentration of inorganic Sb species in different water samples were performed in this work by a novel dispersive liquid-liquid microextraction (DLLME) method based on the application of a magnetic ionic liquid (MIL) and electrothermal atomic absorption spectroscopy (ETAAS) detection. The Sb(iii) species was selectively extracted by complexation with ammonium diethyldithiophosphate (DDTP) and 45 μL of the MIL trihexyl(tetradecyl)phosphonium tetrachloroferrate ([P6,6,6,14]FeCl4) as extractant. Subsequently, a magnetic rod was applied for phase separation, introducing it directly into the sample solution, and the MIL phase was then diluted in chloroform. Afterwards, 15 μL of this solution was injected into the graphite furnace of ETAAS for Sb determination. A multivariate study was performed to obtain the optimal extraction conditions. Selective reduction of Sb(v) to Sb(iii) with 1% (w/v) KI before preconcentration was applied for total inorganic Sb determination and Sb(v) concentration was calculated by subtraction. The analytical performance of the method included extraction efficiencies of 98.0% for Sb(iii) and 92.6% for Sb(v), LOD of 0.02 μg L-1 for Sb(iii) and relative standard deviations of 3.1% for Sb(iii) and 3.5% for Sb(v) (at 6 μg L-1 Sb(iii) and Sb(v), n = 10). The calibration linear range was 0.08-20 μg L-1. The results showed that the proposed methodology was highly sensitive and selective for Sb speciation analysis in tap, dam, mineral, wetland, underground, rain and river water samples.

Room Temperature Ionic Liquids-Based Electrochemical Sensors: An Overview on Paracetamol Detection

Paracetamol (PAR) is an effective antipyretic and analgesic drug utilized worldwide, safer at therapeutic levels but over-dosing and the chronic usage of PAR results in accumulation of toxic metabolites, which leads to kidney and liver damages. Hence, a simple, rapid, cost-effective, and sensitive analytical technique is needed for the accurate determination of PAR in pharmaceutical and biological samples. Though numerous techniques have been reported for PAR detection, electrochemical methods are being receiving more interest due to their advantages. Moreover, in the past few decades, room temperature ionic liquids (RTILs) have been utilized in electrochemical sensors due to their attractive properties. In this present review, authors gathered research findings available for the determination of PAR using RTIL-based electrochemical sensors and discussed. The advantages and limitations in these systems as well as the future research directions are summarized.

Miniaturized sample preparation techniques and ambient mass spectrometry as approaches for food residue analysis

Analytical methods such as liquid chromatography (LC) and mass spectrometry (MS) are widely used techniques for the analyses of different classes of compounds. This is due to their highlighted capacity for separating and identifying components in complex matrices such food samples. However, in most cases, effective analysis of the target analyte becomes challenging due to the complexity of the sample, especially for quantification of trace concentrations. In this case, miniaturized sample preparation methods have been used as a strategy for analysis of complex matrices. This involves removing the interferents and concentrating the analytes in a sample. These methods combine simplicity and effectiveness and given their miniaturized scale, they are in accordance with green chemistry precepts. Besides, ambient mass spectrometry represents a new trend in fast and rapid analyses, especially for qualitative and screening analysis. However, for complex matrix analyses, sample preparation is still a difficult step and the miniaturized sample preparation techniques show great potential for an improved and widespread use of ambient mass spectrometry techniques. . This review aims to contribute as an overview of current miniaturized sample preparation techniques and ambient mass spectrometry methods as different approaches for selective and sensitive analysis of residues in food samples.

Efficient Low-Cost Procedure for Microextraction of Estrogen from Environmental Water Using Magnetic Ionic Liquids

In this study, three magnetic ionic liquids (MILs) were investigated for extraction of four estrogens, i.e., estrone (E1), estradiol (E2), estriol (E3), and ethinylestradiol (EE2), from environmental water. The cation trihexyl(tetradecyl)phosphonium ([P₆₆₆₁₄]⁺), selected to confer hydrophobicity to the resulting MIL, was combined with tetrachloroferrate(III), ferricyanide, and dysprosium thiocyanate to yield ([P₆₆₆₁₄][FeCl₄]), ([P₆₆₆₁₄]₃[Fe(CN)₆]), and ([P₆₆₆₁₄]₅[Dy(SCN)₈]), respectively. After evaluation of various strategies to develop a liquid–liquid microextraction technique based on synthesized MILs, we placed the MILs onto a magnetic stir bar and used them as extracting solvents. After extraction, the MIL-enriched phase was dissolved in methanol and injected into an HPLC–UV for qualitative and quantitative analysis. An experimental design was used to simultaneously evaluate the effect of select variables and optimization of extraction conditions to maximize the recovery of the analytes. Under optimum conditions, limits of detection were in the range of 0.2 (for E3 and E2) and 0.5 μg L⁻¹ (for E1), and calibration curves exhibited linearity in the range of 1–1000 μg L⁻¹ with correlation coefficients higher than 0.998. The percent relative standard deviation (RSD) was below 5.0%. Finally, this method was used to determine concentration of estrogens in real lake and sewage water samples.

A gadolinium-based magnetic ionic liquid for dispersive liquid-liquid microextraction

A hydrophobic gadolinium-based magnetic ionic liquid (MIL) was investigated for the first time as an extraction solvent in dispersive liquid–liquid microextraction (DLLME). The tested MIL was composed of trihexyl(tetradecyl)phosphonium cations and paramagnetic gadolinium chloride anions. The prepared MIL showed low water miscibility, reasonable viscosity, markedly high magnetic susceptibility, adequate chemical stability, low UV background, and compatibility with reversed-phase HPLC solvents. These features resulted in a more efficient extraction than the corresponding iron or manganese analogues. Accordingly, the overall method sensitivity and reproducibility were improved, and the analysis time was reduced. The applicability of the proposed MIL was examined through the microextraction of four sartan antihypertensive drugs from aqueous samples followed by reversed-phase HPLC with UV detection at 240 nm. The DLLME procedures were optimized for disperser solvent type, MIL mass, disperser solvent volume, as well as acid, base, and salt addition. The limits of quantitation (LOQs) obtained with the analysis of 1.2-mL samples after DLLME and HPLC were 80, 30, 40, and 160 ng/mL for azilsartan medoxomil, irbesartan, telmisartan, and valsartan, respectively. Correlation coefficients were greater than 0.9988 and RSD values were in the range of 2.48–4.07%. Under the optimized microextraction conditions and using a 5-mL sample volume, enrichment factors were raised from about 40 for all sartans using a 1.2-mL sample to 175, 176, 169, and 103 for azilsartan medoxomil, irbesartan, valsartan, and telmisartan, respectively. The relative extraction recoveries for the studied sartans in river water varied from 82.5 to 101.48% at a spiked concentration of 0.5 μg/mL for telmisartan and irbesartan and 1 μg/mL for azilsartan medoxomil and valsartan.

The Current Role of Graphene-Based Nanomaterials in the Sample Preparation Arena

Since its discovery in 2004 by Novoselov et al., graphene has attracted increasing attention in the scientific community due to its excellent physical and chemical properties, such as thermal/mechanical resistance, electronic stability, high Young's modulus, and fast mobility of charged atoms. In addition, other remarkable characteristics support its use in analytical chemistry, especially as sorbent. For these reasons, graphene-based materials (GBMs) have been used as a promising material in sample preparation. Graphene and graphene oxide, owing to their excellent physical and chemical properties as a large surface area, good mechanical strength, thermal stability, and delocalized π-electrons, are ideal sorbents, especially for molecules containing aromatic rings. They have been used in several sample preparation techniques such as solid-phase extraction (SPE), stir bar sorptive extraction (SBSE), magnetic solid-phase extraction (MSPE), as well as in miniaturized modes as solid-phase microextraction (SPME) in their different configurations. However, the reduced size and weight of graphene sheets can limit their use since they commonly aggregate to each other, causing clogging in high-pressure extractive devices. One way to overcome it and other drawbacks consists of covalently attaching the graphene sheets to support materials (e.g., silica, polymers, and magnetically modified supports). Also, graphene-based materials can be further chemically modified to favor some interactions with specific analytes, resulting in more efficient hybrid sorbents with higher selectivity for specific chemical classes. As a result of this wide variety of graphene-based sorbents, several studies have shown the current potential of applying GBMs in different fields such as food, biological, pharmaceutical, and environmental applications. Within such a context, this review will focus on the last five years of achievements in graphene-based materials for sample preparation techniques highlighting their synthesis, chemical structure, and potential application for the extraction of target analytes in different complex matrices.

The Influence of Ionic Liquids on the Effectiveness of Analytical Methods Used in the Monitoring of Human and Veterinary Pharmaceuticals in Biological and Environmental Samples-Trends and Perspectives

Recent years have seen the increased utilization of ionic liquids (ILs) in the development and optimization of analytical methods. Their unique and eco-friendly properties and the ability to modify their structure allows them to be useful both at the sample preparation stage and at the separation stage of the analytes. The use of ILs for the analysis of pharmaceuticals seems particularly interesting because of their systematic delivery to the environment. Nowadays, they are commonly detected in many countries at very low concentration levels. However, due to their specific physiological activity, pharmaceuticals are responsible for bioaccumulation and toxic effects in aquatic and terrestrial ecosystems as well as possibly upsetting the body's equilibrium, leading to the dangerous phenomenon of drug resistance. This review will provide a comprehensive summary of the use of ILs in various sample preparation procedures and separation methods for the determination of pharmaceuticals in environmental and biological matrices based on liquid-based chromatography (LC, SFC, TLC), gas chromatography (GC) and electromigration techniques (e.g., capillary electrophoresis (CE)). Moreover, the advantages and disadvantages of ILs, which can appear during extraction and separation, will be presented and attention will be given to the criteria to be followed during the selection of ILs for specific applications.

Novel functionalized magnetic ionic liquid green separation technology coupled with high performance liquid chromatography: A rapid approach for determination of estrogens in milk and cosmetics

Several magnetic ionic liquids (MILs), [P_6,6,6,14⁺][FeCl₄^-], [P_6,6,6,14⁺]₂[MnCl₄^2-], [P_6,6,6,14⁺]₂[CoCl₄^2-] and [P_6,6,6,14⁺]₂[NiCl₄^2-] were synthesized and applied for the extraction of six estrogens (estrone, estradiol, 17-α-hydroxyprogesterone, chloromadinone 17-acetate, megestrol 17-acetate and medroxyprogesterone 17-acetate) in dispersive liquid-liquid microextraction (DLLME). The [CoCl₄^2-]-based MIL was selected as extraction solvent for the separation and concentration of estrogens from milk and cosmetics due to its visual recognition, no sign of hydrolysis, solution acquisition easier and the highest extraction capacity. In addition, the [CoCl₄^2-]-based MIL with low UV absorbance allows direct analysis of the extraction solvent by HPLC-UV. The influence of the mass of MIL, extraction time, salt concentration, and the pH of the sample solution was investigated to obtain optimized extraction efficiency. Besides, extraction conditions including salt concentration, mass of MIL and extraction time were further optimized by the Box-Behnken design through the response surface method. Under optimized conditions, the limits of detection (LODs) of all estrogens were ranged from 5 ng mL^-1 to 15 ng mL^-1. The recoveries ranging from 98.5% to 109.3% in milk and from 96.3% to 111.4% in cosmetics were also studied, respectively. Furthermore, the proposed method were statistically compared with the reported conventional IL-DLLME method and the National standard methods of food safety and cosmetics. The experimental results showed that the functionalized MIL could successfully applied for extraction, separation and pretreatment of estrogens in milk and cosmetics.

Extraction of DNA with magnetic ionic liquids using in situ dispersive liquid-liquid microextraction

A new class of magnetic ionic liquids (MILs) with metal-containing cations was applied in in situ dispersive liquid-liquid microextraction (DLLME) for the extraction of long and short double-stranded DNA. For developing the method, MILs comprised of N-substituted imidazole ligands (with butyl-, benzyl-, or octyl-groups as substituents) coordinated to different metal centers (Ni²⁺, Mn²⁺, or Co²⁺) as cations, and chloride anions were investigated. These water-soluble MILs were reacted with the bis[(trifluoromethyl)sulfonyl]imide anion during the extraction to generate a water-immiscible MIL capable of preconcentrating DNA. The feasibility of combining the extraction methodology with anion-exchange high-performance liquid chromatography with diode array detection (HPLC-DAD) or fluorescence spectroscopy was studied. The method with the Ni²⁺- and Co²⁺-based MILs was easily combined with fluorescence spectroscopy and provided a faster and more sensitive method than HPLC-DAD for the determination of DNA. In addition, the method was compared to conventional DLLME using analogous water-immiscible MILs. The developed in situ MIL-DLLME method required only 3 min for DNA extraction and yielded 1.1-1.5 times higher extraction efficiency (EFs) than the conventional MIL-DLLME method. The in situ MIL-DLLME method was also compared to the trihexyl(tetradecyl)phosphonium tris(hexafluorocetylaceto)nickelate(II) MIL, which has been used in previous DNA extraction studies. EFs of 42-99% were obtained using the new generation of MILs, whereas EFs of only 20-38% were achieved with the phosphonium MIL. This new class of MILs is simple and inexpensive to prepare. In addition, the MILs present operational advantages such as easier manipulation in comparison to hydrophobic MILs, which can have high viscosities. These MILs are a promising new class of DNA extraction solvents that can be manipulated using an external magnetic field. Graphical abstract Magnetic ionic liquids with metal-containing cations are applied in in situ dispersive liquid-liquid microextraction for the extraction of long and short double-stranded DNA.

Investigating the effect of ligand and cation on the properties of metal fluorinated acetylacetonate based magnetic ionic liquids

The effect of chemical structure on various physiochemical properties including thermal stability, solvent miscibility, magnetic susceptibility and viscosity is studied for acetylacetone based magnetic ionic liquids.

In situ formation of hydrophobic magnetic ionic liquids for dispersive liquid-liquid microextraction

A new class of magnetic ionic liquid (MIL) containing paramagnetic cations has been applied for in situ dispersive liquid-liquid microextraction in the determination of both polar and non-polar pollutants, including ultraviolet filters, polycyclic aromatic hydrocarbons, alkylphenols, a plasticizer and a preservative in aqueous samples. The MILs were based on cations containing Ni(II) metal centers coordinated with four N-alkylimidazole ligands and chloride anions. The MILs were capable of undergoing in situ metathesis reaction with the bis[(trifluoromethyl)sulfonyl]imide ([NTf₂^-]) anion during the microextraction procedure, generating a water-immiscible extraction solvent containing the preconcentrated analytes. The MIL was then isolated by magnetic separation, followed by direct analysis using reversed-phase high performance liquid chromatography with diode array detection. Among all of the studied MILs, those containing the N-butylimidazole and N-benzylimidazole ligands ([Ni(C₄IM)₄²⁺]2[Cl^-] and [Ni(BeIM)₄²⁺]2[Cl^-], respectively) exhibited the best extraction performance. The method under optimum conditions required 5 mL of sample at pH 3, 20 mg of [Ni(C₄IM)₄²⁺]2[Cl^-] or 30 mg of [Ni(BeIM)₄²⁺]2[Cl^-], 300 μL of acetone or acetonitrile as dispersive solvent (depending on the MIL), a 1:2 M ratio of MIL to [NTf₂^-], and 3 min of vortex. The developed method achieved higher extraction efficiency compared to the conventional MIL-dispersive liquid-liquid microextraction mode, with extraction efficiencies of 46.8-88.6% and 65.4-97.0% for the [Ni(C₄IM)₄²⁺]2[Cl^-] and the [Ni(BeIM)₄²⁺]2[Cl^-] MILs (at a spiked level of 81 μg L^-1), respectively, limits of detection down to 5.2 μg L^-1, and inter-day relative standard deviation lower than 16%.

Enhanced magnetic ionic liquid-based dispersive liquid-liquid microextraction of triazines and sulfonamides through a one-pot, pH-modulated approach

In this study, an enhanced variant of magnetic ionic liquid (MIL)-based dispersive liquid-liquid microextraction is put forward. The procedure combines a water insoluble solid support and the [P₆₆₆₁₄⁺][Dy(III)(hfacac)₄^-] MIL, in a one-pot, pH-modulated procedure for microextraction of triazines (TZs) and sulfonamides (SAs). The solid supporting material was mixed with the MIL to overcome difficulties concerning the weighing of MIL and to control the uniform dispersion of the MIL, rendering the whole extraction procedure more reproducible. The pH-modulation during extraction step makes possible the one-pot extraction of SAs and TZs, from a single sample, in 15 min. Overall, the new analytical method developed enjoys the benefits of sensitivity (limits of quantification: 0.034-0.091 μg L^-1) and precision (relative standard deviation: 5.2-8.1%), while good recoveries (i.e., 89-101%) were achieved from lake water and effluent from a municipal wastewater treatment plant. Owing to all of the above, the new procedure can be used to determine the concentrations of SAs and TZs at levels below the maximum residue limits.

Exploiting Fluorescence Spectroscopy To Identify Magnetic Ionic Liquids Suitable for the Isolation of Oligonucleotides

Magnetic ionic liquids (MILs), which incorporate paramagnetic ions, promise to minimize manual user intervention, decrease extraction times, and facilitate rapid recovery of the analyte-enriched extraction solvent. If, however, fluorescence is employed in the downstream analysis of an analyte tagged with a fluorophore, the paramagnetic ion may quench fluorescence by introducing new nonradiative processes. Thus, it is necessary to employ a paramagnetic ion that offers a compromise between possessing a high magnetic moment and not introducing new nonradiative channels. Mn(II), Fe(III), Co(II), and Ni(II) are considered in combination with phosphonium cations and anionic ligands based upon halides or hexafluoroacetylacetonate. Among the possibilities examined, MILs containing Mn(II) provide the best alternative for a model system involving DNA.

Preconcentration of DNA using magnetic ionic liquids that are compatible with real-time PCR for rapid nucleic acid quantification

Nucleic acid extraction and purification represents a major bottleneck in DNA analysis. Traditional methods for DNA purification often require reagents that may inhibit quantitative polymerase chain reaction (qPCR) if not sufficiently removed from the sample. Approaches that employ magnetic beads may exhibit lower extraction efficiencies due to sedimentation and aggregation. In this study, four hydrophobic magnetic ionic liquids (MILs) were investigated as DNA extraction solvents with the goal of improving DNA enrichment factors and compatibility with downstream bioanalytical techniques. By designing custom qPCR buffers, we directly incorporated DNA-enriched MILs including trihexyl(tetradecyl)phosphonium tris(hexafluoroacetylaceto)nickelate(II) ([P_6,6,6,14⁺][Ni(hfacac)₃^-]), [P_6,6,6,14⁺] tris(hexafluoroacetylaceto)colbaltate(II) ([Co(hfacac)₃^-]), [P_6,6,6,14⁺] tris(hexafluoroacetylaceto)manganate(II) ([Mn(hfacac)₃^-]), or [P_6,6,6,14⁺] tetrakis(hexafluoroacetylaceto)dysprosate(III) ([Dy(hfacac)₄^-]) into reaction systems, thereby circumventing the need for time-consuming DNA recovery steps. Incorporating MILs into the reaction buffer did not significantly impact the amplification efficiency of the reaction (91.1%). High enrichment factors were achieved using the [P_6,6,6,14⁺][Ni(hfacac)₃^-] MIL for the extraction of single-stranded and double-stranded DNA with extraction times as short as 2 min. When compared to a commercial magnetic bead-based platform, the [P_6,6,6,14⁺][Ni(hfacac)₃^-] MIL was capable of producing higher enrichment factors for single-stranded DNA and similar enrichment factors for double-stranded DNA. The MIL-based method was applied for the extraction and direct qPCR amplification of mutation prone-KRAS oncogene fragment in plasma samples. Graphical abstract Magnetic ionic liquid solvents are shown to preconcentrate sufficient KRAS DNA template from an aqueous solution in as short as 2 min without using chaotropic salts or toxic organic solvents. By using custom-designed qPCR buffers, DNA can be directly amplified and quantified from four MILs examined in this study.

Development of a new pH assisted homogeneous liquid-liquid microextraction by a solvent with switchable hydrophilicity: Application for GC-MS determination of methamphetamine

In this study, a new method based on homogeneous liquid-phase microextraction was developed for the determination of methamphetamine (MA) in urine samples. Dipropylamine (DPA), as a solvent with switchable hydrophilicity, was used as the extraction solvent and can be miscible/immiscible based on variable pH values of the aqueous sample solution. The effects of operational extraction parameters such as DPA volume, temperature, the amount of added acid and base solutions, and NaCl content of the sample were investigated. Under optimal conditions the preconcentration factor, limit of detection and linearity of the method were achieved in the ranges of 98.8, 1.5 µgL^-1 and 5-1500 µgL^-1, respectively. Also, within-run precision, between-run precision and robustness of the method were investigated. Finally, the proposed method was successfully applied to the analysis of MA in urine sample.

Dispersive liquid–liquid microextraction using magnetic room temperature ionic liquid for extraction of ultra-trace amounts of parabens

In this work, a dispersive liquid–liquid microextraction method using methyltrioctylammonium tetrachloroferrate was employed for the extraction of ultratrace amounts of parabens in water, beer and beverage samples.