Formation of by-products during chemical interesterification of lipids. Detection and characterization of dialkyl ketones by non-aqueous reversed-phase liquid chromatography-high resolution mass spectrometry and gas chromatography-mass spectrometry

The Novel Approach of Catalytic Interesterification, Hydrolysis and Transesterification of Pongamia pinnata Oil

The properties of biodiesel are completely dependent on the fatty acid profile of feedstock oils. Several feedstocks are not in use for biodiesel production because of the presence of unsuitable fatty acids in their oils. The present study was conducted to overcome this problem by the utilization of interesterification and hydrolysis processes. The present study reports biodiesel with much better cold flow properties than previous studies. Fatty acids present in Pongamia pinnata oil were optimized via interesterification and hydrolysis treatment of feedstock prior to alkali-catalyzed transesterification. The physiochemical properties of fuel were evaluated by standard test methods and the results were compared with EN 14214 and ASTM D6751 standards. Biodiesel composition was analyzed by a gas chromatographic analysis. The density, saponification and iodine values of the biodiesel derived from treated and non-treated oil were found to be within the range recommended by the international fuel standards. The acid values of biodiesel produced from non-treated and treated fractions were high (0.7–0.8 mg of KOH/g of oil), as compared to the biodiesel produced from non-treated and treated pure oil. The cloud points and pour points of biodiesel produced from hydrolyzed and interesterified oil were in the range of (8.1 to −9.6 °C) and (2.03 to −12.5 °C), respectively, while those of non-treated oil were in the range of (13.37 to −1.53 °C). These results indicate that treatments of oil specifically improved the low-temperature properties of biodiesel.

Microwave-Assisted Saponification Method Followed by Solid-Phase Extraction for the Characterization of Sterols and Dialkyl Ketones in Fats

Unlike other fields, the methods routinely applied for fats and oils are still tied to traditional, time- and solvent-consuming procedures, such as saponification, column chromatography and thin-layer chromatography. In this paper, microwave-assisted saponification followed by a lab-made solid-phase extraction was optimized for the characterization of either dialkyl ketones (DAK) or sterols or both simultaneously. The instrumental determination was performed by gas chromatography- flame ionization detector (GC-FID) for quantification and gas chromatography-mass spectrometry (GC-MS) for confirmation purposes. The proposed method showed good recoveries (>80%) and limit of quantification (0.04–0.07 μg/g for the 4 DAK and of 0.07 μg/g for α-cholestanol). Repeatabilities (n = 3) were below 15% for DAKs and generally lower than 6% for sterols. Accuracy on the entire sterol profile was confirmed in comparison to the International Olive Council reference method. The method was finally applied to real-world samples before and after chemical interesterification.

Dialkylketones in Paperboard Food Contact Materials-Method of Analysis in Fatty Foods and Comparative Migration into Liquid Simulants Versus Foodstuffs

Dialkyl diketene dimers are used as sizing agents in the manufacture of paper and board for food contact applications to increase wetting stability. Unbound residues can hydrolyze and decarboxylate into dialkylketones. These non-intentionally added substances (NIAS) have potential to migrate to fatty foods in contact with those packaging materials. In Germany, the Federal Institute for Risk Assessment (BfR) established a specific migration limit (SML) of 5 mg/kg for the transfer of these dialkylketones into foodstuffs. In order to investigate the differences between simulants and real foods, an analytical method was optimized for extraction and quantification of dialkylketones in edible oils and fatty foods by gas chromatography coupled with flame ionization detection (GC-FID), and additionally by gas chromatography with mass spectrometry (GC-MS), to confirm their identification and to quantify them in case of interferences. Dialkylketones are separated from the extracted fat by alkaline saponification of the triglycerides. Dialkylketones migration from paper-based food contact articles into organic solvents isooctane and dichloromethane, in olive and sunflower oils, and in fatty foods (croissants, Gouda, cheddar cheese, and salami was studied). As a result, it was found that the simulating tests, including the edible oil extraction tests, gave migration values that exceeded the SML largely, while the migration with the food samples were largely below the SML.

Strategies and Challenges for the Development of Industrial Enzymes Using Fungal Cell Factories

Industrial enzymes have been produced from microorganisms for more than a century. Today, a large share of enzyme products is manufactured using recombinant microorganisms. This chapter focuses on major industrial fungal species belonging to the ascomycetes like Aspergillus niger, A. oryzae, and Trichoderma reesei. Many of the commercially available recombinant enzymes are manufactured using fungi. Examples of fungal enzymes used in food products are described. The enzyme industry is to a large extent cost-driven, so the enzyme product needs to meet strict COGS (cost of goods sold) targets. Therefore, the cell factory must be very efficient to produce the enzyme in high titers and efficiently utilize raw materials. Secondly, it must be designed for a robust and generic fermentation process. When developing fungal hosts for enzyme production, several properties of the system need to be considered relating to efficiency of the cell factory, purity of the product, and safety of both the cell factory and the product. Purity is secured by engineering of the cell factory, and properties related to safety must also be engineered into the fungal host. The methods used for strain improvement are continuously being developed to increase yields and are described herein. More automation using precision tools for modification of the genome (i.e., CRISPR) and low-cost sequencing have vastly expanded the possibilities and enabled fast strain development. Using systems biology approaches, better understanding of cellular processes is now possible enabling advanced engineering of fungal cell factories. Surprisingly, a survey of innovation in the field revealed a decrease in the number of patent applications in recent years. Finally, the requirements for enzyme approval, especially in food and feed, have increased significantly worldwide in the last few years. A description of the regulatory landscape and its challenges in food and feed is included.