Partially carbonized cellulose filter paper as a green adsorbent for the extraction of pesticides from fruit juices

Development of a polyurethane-coated thin film solid phase microextraction device for multi-residue monitoring of pesticides in fruit and tea beverages

A novel solid-phase microextraction device coated with an efficient and cheap thin film of polyurethane was developed for trace determination of 13 widely used pesticides in fruit and tea beverages. A round-shaped polyurethane film covering the bottom of a glass vial was fabricated as the sorbent to exhibit a superior capacity for preconcentrating target compounds and reducing matrix interferences. After optimization of the key parameters including the film type, extraction time, solution pH, ionic strength, desorption solvent, and conditions, this device allowed an efficient adsorption-desorption cycle for the pesticides accomplished in one vial. Coupled with gas chromatography-electron capture detection, the polyurethane-coated thin film microextraction method was successfully established and applied for the analysis of real fruit and tea drinks, showing low limits of detection (0.001-0.015 μg/L), wide linear ranges (1.0-500.0 μg/L, r²  > 0.9931), good relative recoveries (77.2%-106.3%) and negligible matrix effects (86.1%-107.5%) for the target pesticides. The proposed approach revealed strong potential of extending its application by flexibly modifying the type or size of the coating film. This study provides insights into the enrichment of contaminants from complex samples using inexpensive and reusable microextraction devices that can limit the environmental and health impact of the sample preparation protocol.

Magnetic dispersive solid phase extraction based on carbonized cellulose-ferromagnetic nanocomposite for screening phthalate esters in aqueous samples

In this work, a sorbent of the carbonized cellulose-ferromagnetic nanocomposite has been proposed for the magnetic dispersive solid phase extraction of some plasticizers in aqueous samples. Carbonized cellulose nanoparticles were prepared by treatment of cellulose filter paper with concentrated sulfuric acid and then loaded on Fe₃O₄ nanoparticles using coprecipitation. This sorbent is compatible with aqueous samples and can be considered as a viable sorbent for extraction of plasticizers from aqueous samples. In this study, magnetic dispersive solid phase extraction is followed by a dispersive liquid-liquid microextraction method. This combination makes the proposed approach as an efficient clean-up method with high enrichment factors for the selected analytes. The enriched analytes are monitored by gas chromatography equipped with a flame ionization detector. Parameters affecting the method efficiency were investigated in details. Under the optimized extraction conditions, limits of detection could reach up to of 0.15-0.50 µg L^-1. The satisfactory enrichment factors of 286-403 were obtained, and the extraction recoveries were found to be in the range of 57-80%. Relative standard deviations were in the range of 3-7% for intra-day and inter-day precisions for six replicate extractions at 25 µg L^-1 of each plasticizer. Calibration curves were linear in wide ranges with coefficients of determination ≥ 0.995. Eventually, efficiency of the prepared sorbent was confirmed by the extraction of some plasticizers from real samples including fruit juices, mineral water, injection solution, cola, and yoghourt drink packed in plastic containers.

A paper-based polystyrene/nylon Janus platform for the microextraction of UV filters in water samples as proof-of-concept

A new mix-mode cellulose-based sorptive phase is described that combines two different polymeric domains (i.e., nylon and polystyrene), thus providing simultaneous hydrophilic and hydrophobic features as a result. By analogy with Janus materials, the new paper-based sorptive phase has been named paper-based polystyrene/nylon Janus-platform (P-Ps/Ny-JP). The main advantages of the proposed P-Ps/Ny-JP are the sustainability, simplicity in synthesis, and low cost of this extraction device. The main parameters affecting the synthesis (i.e., coating procedure and polymers proportion) have been studied, and the resulting material has been characterized via scanning electron microscopy and infrared spectroscopy. As a proof-of-concept, the simultaneous extraction of fourteen UV filters of a wide range of polarity, with log P values ranging from - 0.234 to 16.129, from water samples and their determination by liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been performed. The proposed methodology enables the determination of these chemicals with limits of detection from 12 to 71 ng L^-1, and the precision, expressed as a relative standard deviation, was below 15%. The extraction device was applied to the analysis of real water samples likely to contain UV filters (i.e., two private swimming pool water and one seawater) and the recovery values were in the range 73-121%.

Wooden-based materials: Eco-friendly materials for direct mass spectrometric analysis and microextraction

Lignocellulosic materials have arisen as a sustainable alternative in microextraction techniques during the last 10 years. As they are natural materials, their use fits into some of the principles of Green Analytical Chemistry. Their inherent porosity, narrow shape, and rigidity permit their use in ambient ionization mass spectrometry techniques. In particular, the combination of wooden-based materials and direct analysis gives birth to the so-called wooden-tip electrospray ionization mass spectrometry technique. This approach has been used for the direct analysis of complex samples, and as a streamlined tool for fingerprint quality analysis. Also, wooden-based materials can be superficially modified to boost the interaction with target compounds, allowing their isolation from complex samples. This review describes the potential and applicability of direct analysis using lignocellulosic materials, as well as other alternatives related to their use in microextraction.

Application of polysaccharide biopolymers as natural adsorbent in sample preparation

Preparing samples for analyses is perhaps the most important part to analyses. The varied functional groups present on the surface of biopolymers bestow them appropriate adsorption properties. Properties like biocompatibility, biodegradability, presence of different surface functional group, high porosity, considerable absorption capacity for water, the potential for modification, etc. turn biopolymers to promising candidates for varied applications. In addition, one of the most important parts of determination of an analyte in a matrix is sample preparation step and the efficiency of this step in solid phase extraction methods is largely dependent on the type of adsorbent used. Due to the unique properties of biopolymers they are considered an appropriate choice for using as sorbent in sample preparation methods that use from a solid adsorbent. Many review articles have been published on the application of diverse adsorbents in sample preparation methods, however despite the numerous advantages of biopolymers mentioned; review articles in this field are very few. Thus, in this paper we review the reports in different areas of sample preparation that use polysaccharides-based biopolymers as sorbents for extraction and determination of diverse organic and inorganic analytes.