Determination of quinolones in environmental water and fish by magnetic metal organic frameworks based magnetic solid-phase extraction followed by high-performance liquid chromatography-tandem mass spectrometry

Detection methods for antibiotics in wastewater: a review

Antibiotics are widely used as fungicides because of their antibacterial and bactericidal effects. However, it is necessary to control their dosage. If the amount of antbiotics is too much, it cannot be completely metabolized and absorbed, will pollute the environment, and have a great impact on human health. Many antibiotics usually left in factory or aquaculture wastewater pollute the environment, so it is vital to detect the content of antibiotics in wastewater. This article summarizes several common methods of antibiotic detection and pretreatment steps. The detection methods of antibiotics in wastewater mainly include immunoassay, instrumental analysis method, and sensor. Studies have shown that immunoassay can detect deficient concentrations of antibiotics, but it is affected by external factors leading to errors. The detection speed of the instrumental analysis method is fast, but the repeatability is poor, the price is high, and the operation is complicated. The sensor is a method that is currently increasingly studied, including electrochemical sensors, optical sensors, biosensors, photoelectrochemical sensors, and surface plasmon resonance sensors. It has the advantages of fast detection speed, high accuracy, and strong sensitivity. However, the reproducibility and stability of the sensor are poor. At present, there is no method that can comprehensively integrate the advantages. This paper aims to review the enrichment and detection methods of antibiotics in wastewater from 2020 to the present. It also aims to provide some ideas for future research directions in this field.

Developing a novel magnetic organic polymer for selective extraction and determination of 16 macrolides in water and honey samples

A novel magnetic organic polymer Fe3O4@SiO2@Tb-PDAN was designed and synthesized, which was used as an adsorbent for magnetic solid-phase extraction (MSPE) of 16 macrolides (MALs) in water and honey. The synthesized adsorbent was characterized using techniques including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). Then several parameters of the extraction process were further optimized. Under the optimized conditions, an MSPE-LC-MS/MS method was established for extraction and determination of 16 MALs, which showed good linearity (r ≥ 0.999), low limits of detection (0.001-0.012 μg L-1 for water and 0.001-0.367 μg kg-1 for honey) and satisfactory recoveries (70.02-118.91%) with the relative standard deviations (RSDs) lower than 10.0%. This established method was then successfully applied to detect MALs in real samples, which suggested that Fe3O4@SiO2@Tb-PDAN was a potential magnetic adsorbent for efficient extraction and analysis of MALs.

Effective extraction and determination of 24 quinolones in water and egg samples using a novel magnetic covalent organic framework combined with UPLC-MS/MS

The excessive use of quinolones (QNs) has seriously threatened human health. In this study, a novel functionalized magnetic covalent organic framework Fe3O4@SiO2@Ah-COF was fabricated with biphenyl-3,3',5,5'-tetracarbaldehyde and hydrazine hydrate (85%) as monomers and was used as a magnetic solid-phase extraction (MSPE) absorbent for the determination of 24 QNs in water and egg samples through ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The extraction parameters of MSPE were optimized, including pH, adsorbent dosage, adsorption time, and eluent type. An effective and rapid detection method was then established, which showed good linearity (R2 ≥ 0.9990), low limits of detection (0.003-0.036 μg L-1) and low limits of quantitation (0.008-0.110 μg L-1) for QNs. The good recoveries of 24 QNs in water and egg samples were in the range of 70.3-106.1% and 70.4-119.7%, respectively, with relative standard deviations lower than 10% (n = 5). As a result, Fe3O4@SiO2@Ah-COF is a promising magnetic adsorbent, and the established method was successfully applied for the determination of 24 QNs in water and egg samples.

Facile construction of magnetic solid-phase extraction of polyaniline blend poly(amidoamine) dendrimers modified graphene oxide quantum dots for efficient adsorption of polycyclic aromatic hydrocarbons in environmental water

An efficient magneto-adsorbent composed of polyaniline blend poly(amidoamine) dendrimers modified graphene oxide quantum dots and magnetic Fe3O4 particles (Fe3O4@PANI-PSS/PAMAM-QGO) for magnetic solid-phase extraction (MSPE) of polycyclic aromatic hydrocarbons (PAHs) in environmental water was synthesized. Fe3O4@PANI-PSS/PAMAM-QGO exhibited exceptional adsorption property for most PAHs analytes. The nanocomposite sorbent demonstrated a ferromagnetic behavior of 17.457 emu g-1, which is adequate for subsequent use in MSPE. Key parameters affecting the processes of adsorption and desorption, including the sorbent amount, vortex adsorption time, vortex extraction time, sample volume, a solvent for desorption and the solvent volume were all examined and optimized. The performance of MSPE using Fe3O4@PANI-PSS/PAMAM-QGO as adsorbent for four PAHs, including fluoranthene, acenaphthene, phenanthrene and pyrene were studied through high performance liquid chromatography equipped with spectrofluorometer. Under the optimal conditions, Fe3O4@PANI-PSS/PAMAM-QGO showed a wide linearity of 10-1,000 ng mL-1, low detection limit (LOD) ranging from 1.92 to 4.25 ng mL -1 and high accuracy (recoveries of 93.6-96.5 %). Enrichment factors up to 185 were achieved. Furthermore, Fe3O4@PANI-PSS/PAMAM-QGO exhibited good recyclability (10 times, RSDs ≤ 5.35%), while maintaining its high efficiency in the extraction of PAHs. The proposed method was successfully applied for environmental samples. Recoveries ranging from 81.2 to 106.2 % were obtained, indicating a low matrix effect and the robustness of the optimized MSPE method. Based on these features and under the optimal extraction conditions, Fe3O4@PANI-PSS/PAMAM-QGO was demonstrated to be a successful tool for the rapid and sensitive extraction of PAHs in the samples.

Graphene oxide mediated CdSe quantum dots fluorescent aptasensor for high sensitivity detection of fluoroquinolones

In view of the urgent need for fluoroquinolones contamination detection in the fields of food safety, a novel aptasensor based on the fluorescence quenching property of graphene oxide (GO) and the fluorescence characteristic of cadmium selenide quantum dots (CdSe QDs) was developed for fluoroquinolones highly sensitive detection in this work. The CdSe QDs with carboxyl-rich surface were synthesized successfully and fluoresced at 525 nm under the optimal excitation light of 366 nm. Based on the hydrophobic and π-π stacking between GO and aptamer, aptamer labeled by CdSe QDs fluorescence (CdSe QDs-apt) were adsorbed by GO and the fluorescence of CdSe QDs was quenched. After the aptamer combined specifically with fluoroquinolones, greater specific force lead to the desorption of CdSe QDs-apt from GO and fluorescence recovery. Represented by Ciprofloxacin (CIP), a member of fluoroquinolones, the fluorescence emission increased with the increasing of CIP concentrations from 8 nM to 500 nM, and the detection limit was 0.42 nM. The spiked recoveries in real samples of honey and milk were 91.5-96.9 % and 90.3-95.2 %, respectively, indicating that the aptasensor was reliable. Moreover, the fluorescence responses of multiple members of fluoroquinolones were found to be consistent, denoting that the fluorescence aptasensor can be used to detect the total amount of multiple members of fluoroquinolones. These results showed that the aptasensor can be used as a promising platform for fluoroquinolones detection.

Method Validation and Measurement Uncertainty (MU) Evaluation on Enrofloxacin and Ciprofloxacin in the Aquatic Products

This study aimed to investigate a detection method of enrofloxacin and ciprofloxacin to be avail for strictly supervising the quality and safety of aquatic products. The results displayed that the optimal extraction conditions for enrofloxacin and ciprofloxacin were the following five aspects: 15 g dosages of Na2SO4 to dehydrate, 8‰ of acetonitrile and 50% hydrochloric acid to deproteinization, 2 mL dosages of n-hexane to degrease, 10 min of ultrasonic time, and 20 min of extraction (stand) time. Meanwhile, it was also obtained for the optimal detection performance indexes of the recovery, precision, and accuracy from the tests of shrimp, grass carp, and tilapia. In particular, the expanded uncertainties were 2.8601 and 0.8613, and the factors of both the calibration curves (Urel(C)) and the analysis of the experiment (Urel(E)) were the two MU main contributors for enrofloxacin and ciprofloxacin together with the results above 40%. Consequently, the developed novel method was suited for the determination of the enrofloxacin and ciprofloxacin residues in aquatic products and would contribute to reinforce in supervision and inspection of the quality and safety of aquatic products.

Fe3O4@UiO-66-NH2 based on magnetic solid phase extraction for determination of organic UV filters in environmental water samples

In this work, a nanocomposite structured magnetic metal-organic framework named as Fe3O4@UiO-66-NH2 was prepared via a simple hydrothermal approach. The as-mentioned nanocomposite was characterized by Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and the Brunauer-Emmett-Teller (BET) techniques. Using the Fe3O4@UiO-66-NH2 as a nanosorbent, an easy and highly effective approach was developed to preconcentrate nine organic UV filters before gas chromatography-mass spectrometry (GC-MS) analysis. Different conditions influencing the extraction efficiency encompassing the sorbent amount, nature and volume of desorption solvent, desorption time, pH of the sample, and extraction time, were examined. Under the optimal experimental parameters, the Fe3O4@UiO-66-NH2-based magnetic solid phase extraction and GC-MS (MSPE-GC-MS) demonstrated linearity in the range of 0.03-1500 ng/L (R2 ≥ 0.9974) and the reproducibility, expressed as RSD, was ≤7.5%. The limits of detection ranged between 0.01 and 0.07 ng/L and limits of quantification were in the range of 0.03-0.4 ng/L. Finally, the suggested approach was satisfactorily utilized to determine nine organic UV filters in different water samples (analytical recoveries between 86.5% and 104.2%).

Fabrication of a magnetic metal-organic framework/covalent organic framework composite for simultaneous magnetic solid-phase extraction of seventeen trace quinolones residues in meats

Effective capture of quinolones (QNs) in animal-derived food is a vital procedure for food safety monitoring. However, the lack of adsorption specificity and difficult to recycle in complex substrate conditions have been major problems for most of the adsorbents. In this work, a magnetic Fe3O4/MOF/COF composite (named Fe3O4@NH2-MIL-125@TpPa-SO3H) was successfully synthesized with good magnetic responsiveness and conspicuous affinity towards QNs. The Fe3O4/MOF/COF composite was used as a magnetic solid-phase extraction (MSPE) adsorbent for pretreatment and determination of QNs in meat samples. Under optimal MSPE conditions in combination with high performance liquid chromatography-quadrupole orbitrap high resolution mass spectrometer (HPLC-Q-Orbitrap HRMS), the proposed method had good linearity (R2 ≥ 0.9978) from 0.01 to 100ng g-1, low limits of detection (0.0016 to 0.0940ng g-1), good precision with relative standard deviations lower than 5.8%. This method was effectively applied to the detection of 17 QNs in the spiked pork, chicken and beef samples with satisfactory recoveries from 83.9 to 106.2%. The separation selectivity mainly due to the π-π interaction, hydrogen bonding, and electrostatic attraction between QNs and the sulfonic acid and amino functional groups of the composite. After verification, the stability and reusability of the composite meet the requirements of complex matrix sample pretreatment. The developed MSPE method based on the magnetic Fe3O4/MOF/COF composite provided an ideal sample pretreatment alternative for determining trace QNs in complex matrixes with selectivity, simplicity, rapidity, and efficiency.

Multivariate covalent organic frameworks guided carboxyl functionalized magnetic adsorbent for enrichment of fluoroquinolones in milk prior to high performance liquid chromatographic analysis

Herein, we prepared a carboxyl functionalized magnetic covalent organic framework (Fe3O4@iCOF-COOH) by combining multivariate synthetic strategy with post-synthetic modification. It was used as an adsorbent for magnetic solid phase extraction (MSPE) of six fluoroquinolones (FQs), and showed good absorption performance at neutral pH. Carboxyl groups are found to be crucial for the adsorption of fluoroquinolones. The adsorption mechanism was primarily attributed to strong hydrogen bonding, π-π interaction as well as potential hydrophobic effect. The optimal extraction conditions are sample pH at 6.0, adsorbent dosage of 3 mg, eluent of 1.0 mL methanol solution containing 7.5% ammonia, and extraction/desorption time of 30 min. Under the optimized conditions, the Fe3O4@iCOF-COOH was used as an adsorbent for MSPE of FQs in milk, an analytical method was established by combining with high-performance liquid chromatography-ultraviolet detection (HPLC-UV). The limits of detection (LODs) and limit of quantification (LOQs) were 1.24-4.58 ng⋅mL-1 and 4.12-15.3 ng⋅mL-1, respectively. The recoveries of target FQs in spiked milk were 68.4-105%. This work provides a new way to prepare covalent organic framework based adsorbents for solid phase extraction, and can be readily extended to other type of adsorbents.

One Stone Two Birds: An Upconversion Nanosensor for Sensitive Detection of Fluoroquinolones in Aquatic Products Based on Chelation Recognition

Excessive residues of fluoroquinolones (FQs) in aquatic products have become a growing issue in recent years. Herein, we demonstrate an upconversion fluorescence nanosensor constructed by a one-stone-two-birds strategy, where Fe3+ not only quenches upconversion fluorescence with high efficiency but also specifically recognizes the bidentate ligand structure of FQs. Compared to existing methods, the proposed sensor is simpler to synthesize and cheap and has more storage stability due to the unification of the quencher and recognition molecule. Enrofloxacin (ENR) was chosen as a representative veterinary drug for FQs to verify the effectiveness of the nanosensor. Under optimal conditions, the range of detection for ENR was 2.0 × 10-2 to 2.0 × 102 μg/mL, with a limit of detection of 1.08 × 10-3 μg/mL. The developed nanosensor was further validated by high-performance liquid chromatography-ultraviolet (HPLC-UV) without significant differences in practical detection. Hence, this study offers a potential strategy for the detection of FQs.

Characterization, specific recognition, and the performance in fish matrix of a shark-derived single-domain antibody against enrofloxacin

The third generation of genetic engineering antibodies, single-domain antibodies, have been widely reported as potential biomaterials in recognizing small molecular hazards. In this study, a shark-derived single-domain antibody was used as the recognition element for the first time to detect enrofloxacin (ENR), one of the most representative hazards in aquaculture. An ENR-specific clone named 2E6 was isolated by phage display technology. Experimental results proved that 2E6 ssdAb showed high affinity to ENR-PEI complete antigen, with the highest OD₄₅₀ value of 1.348 in binding ELISA. Through icELISA, it was determined that the IC₅₀ of 2E6 ssdAb to ENR was 19.230 ng/mL, while the IC₁₀ was 0.975 ng/mL, with rare recognition to other fluoroquinolones, which showed high sensitivity and specificity to ENR. The 2E6 ssdAb also performed excellently in fish matrix immunoassay. Results showed that the ENR-negative fish matrix did not seriously interfere with the recognition of 2E6 ssdAb to ENR-OVA, with the matrix index between 4.85% and 11.75%, while the results of icELISA in ENR-spiked fish matrix showed that 2E6 ssdAb could recognize the target ENR in different ENR-spiked concentrations of the fish matrix (10-1000 ng/mL), with the recovery between 89.30% and 126.38% and the RSD between 1.95% and 9.83%. This study broadens the application scenario of shark-derived single-domain antibodies as small molecule recognition biomaterials, providing a new recognition element on ENR detection for immunoassay.

Preparation of amine-modified amphiphilic resins for the extraction of trace pharmaceuticals and personal care products in environmental waters

Herein, four amine-modified amphiphilic resins were synthesized and utilized as solid-phase extraction (SPE) materials to enrich pharmaceuticals and personal care products (PPCPs) from environmental water. The obtained materials (Strong anion-exchange amphiphilic materials, SAAMs; Weak anion-exchange amphiphilic materials, WAAMs) possessed large specific surface area (473-626 m²/g), high ion exchange capacity (0.89-1.97 mmol/g), and small contact angle (74.41-79.74°), indicating good hydrophilicity. The main factors affecting the efficiency of the extraction process were studied, including column volume, column flow rate, sample salinity and sample pH. Notably, the trend observed in absolute recovery was significantly correlated with the Zeta potential of the employed adsorbents. Furthermore, based on the obtained materials, a method of SPE coupled with ultra-performance liquid chromatography and tandem mass spectrometry (SPE/LC-MS/MS) was developed, and then utilized to determine PPCPs in the samples collected from the Yangtze River Delta. The Method detection limit (MDL) and Method quantification limit (MQL) ranged from 0.05 to 0.60 ng/L and 0.17 to 2.00 ng/L, respectively, with a relative standard deviation (RSD) below 6.3%, demonstrating good accuracy and sensitivity. As evidenced by comparison with previous literature, the developed method exhibited satisfactory performance, showing great potential for further commercial application in the extraction of trace PPCPs from environmental water samples.

The Ultratrace Determination of Fluoroquinolones in River Water Samples by an Online Solid-Phase Extraction Method Using a Molecularly Imprinted Polymer as a Selective Sorbent

Fluoroquinolones (FQs) are broad-spectrum antibiotics widely used to treat animal and human infections. The use of FQs in these activities has increased the presence of antibiotics in wastewater and food, triggering antimicrobial resistance, which has severe consequences for human health. The detection of antibiotics residues in water and food samples has attracted much attention. Herein, we report the development of a highly sensitive online solid-phase extraction methodology based on a selective molecularly imprinted polymer (MIP) and fluorescent detection (HPLC-FLD) for the determination of FQs in water at low ng L−1 level concentration. Under the optimal conditions, good linearity was obtained ranging from 0.7 to 666 ng L−1 for 7 FQs, achieving limits of detection (LOD) in the low ng L−1 level and excellent precision. Recoveries ranged between 54 and 118% (RSD < 17%) for all the FQs tested. The method was applied to determining FQs in river water. These results demonstrated that the developed method is highly sensitive and selective.

A novel terbium (III) and aptamer-based probe for label-free detection of three fluoroquinolones in honey and water samples

Fluoroquinolones, a family of synthetic broad-spectrum antibiotics, are widely used in clinical medicine, farm animals and aquaculture. Residues of fluoroquinolones in samples have attracted much attention because of growing food safety and public health concerns. Here, a novel Tb³⁺ ion-enrofloxacin aptamer coordination probe was prepared to develop a sensitive and rapid label-free fluorescence assay for specific detection three fluoroquinolones. In presence of the target, Tb³⁺ ion- enrofloxacin aptamer probe specifically bound with enrofloxacin, norfloxacin and ciprofloxacin, leading to a sharp increase in fluorescence emission of the probe. Under the optimized conditions, fluorescence increased linearly in the 1.0-100.0 ng/mL range for the three fluoroquinolones, with 0.053 ng/mL limit of detection for ciprofloxacin, 0.020 ng/mL limit of detection for norfloxacin and 0.061 ng/mL limit of detection for enrofloxacin. Satisfactory recovery (80.10-102.48%) in spiked honey and water samples were obtained for the three fluoroquinolones with relative standard deviations between 0.21% and 5.44% (n = 3).

Determination of quinolone antibiotics in environmental water using automatic solid-phase extraction and isotope dilution ultra-performance liquid chromatography tandem mass spectrometry

The widespread use of quinolones in humans and animals has become a major threat to public health. In this study, a simple, rapid, sensitive, and high throughput method based on automatic solid-phase extraction and isotope dilution ultra-performance liquid chromatography tandem mass spectrometry was described for the determination of trace quinolones in environmental water. The proposed automated solid-phase extraction method was initially optimized, and the optimum experimental conditions found were 1 L water sample with 0.5 g/L Na₂EDTA (pH 3) extracted and enriched by CNW Poly-Sery HLB cartridge at a flow rate of 50 mL/min and eluted by 8 mL of methanol. The linearity of the method ranged from 0.05 to 100 μg/L for 15 quinolones, with correlation coefficients ranging from 0.9993 to 0.9999. The limits of detection were in the low ng/L level, ranging from 0.005 to 0.051 ng/L. Finally, the optimized method was applied for determining trace levels of 15 quinolones in Wahaha pure water, tap water, river water, and seawater samples with good recoveries of 93 %-119 % and satisfactory relative standard deviations of 0.1 %-13.9 %. Fourteen quinolones were detected, and ofloxacin was the predominant congener in river water and seawater.

Covalent Organic Framework/Polyacrylonitrile Electrospun Nanofiber for Dispersive Solid-Phase Extraction of Trace Quinolones in Food Samples

The extraction of quinolone antibiotics (QAs) is crucial for the environment and human health. In this work, polyacrylonitrile (PAN)/covalent organic framework TpPa–1 nanofiber was prepared by an electrospinning technique and used as an adsorbent for dispersive solid-phase extraction (dSPE) of five QAs in the honey and pork. The morphology and structure of the adsorbent were characterized, and the extraction and desorption conditions for the targeted analytes were optimized. Under the optimal conditions, a sensitive method was developed by using PAN/TpPa–1 nanofiber as an adsorbent coupled with high-performance liquid chromatography (HPLC) for five QAs detection. It offered good linearity in the ranges of 0.5–200 ng·mL⁻¹ for pefloxacin, enrofloxacin, and orbifloxacin, and of 1–200 ng·mL⁻¹ for norfloxacin and sarafloxacin with correlation coefficients above 0.9946. The limits of detection (S/N = 3) of five QAs ranged from 0.03 to 0.133 ng·mL⁻¹. The intra-day and inter-day relative standard deviations of the five QAs with the spiked concentration of 50 ng·mL⁻¹ were 2.8–4.0 and 3.0–8.8, respectively. The recoveries of five QAs in the honey and pork samples were 81.6–119.7%, which proved that the proposed method has great potential for the efficient extraction and determination of QAs in complex samples.

Graphene oxide modified magnetic polyamidoamide dendrimers based magnetic solid phase extraction for sensitive measurement of polycyclic aromatic hydrocarbons

In this study, graphene oxide modified magnetic polyamidoamine dendrimers (MNPs@PAMAM-G2.0@GO) nanoparticles were successfully prepared by amidation method. The obtained MNPs@PAMAM-G2.0@GO nanocomposites were examined by fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), scanning electron microscope (SEM) and transmission electron microscopy (TEM), etc. MNPs@PAMAM-G2.0@GO exhibited excellent adsorption property and was investigated for magnetic solid phase extraction (MSPE) of polycyclic aromatic hydrocarbons (PAHs) from water. The detection of extracted PAHs was accomplished by high performance liquid chromatography (HPLC) and gas chromatography tandem mass spectrometry (GC-MS/MS). The target PAHs included anthracene (ANT), pyrene (PYR), fluoranthene (FLT), carbazole (CB), 7-methylquinoline (7-MQL), 9-methylcarbazole (9-MCB), dibenzothiophene (DBT) and 4,6-dimethyldibenzothiophene (4,6-DBT). Important operation parameters for MSPE that could affect the extraction efficiencies of PAHs were investigated in detail. Under optimal parameters, the constructed method demonstrated excellent linear range with 0.001-10 μg L^-1 for analytes and low limits of detection within the range of 0.11-0.9 ng L^-1. The spiked average recoveries of PAHs in natural water samples ranged from 92.5% to 105.2%. The promising results indicated that MNPs@PAMAM-G2.0@GO could be employed to efficiently extract PAHs from aqueous samples.

Use of hydroxypropyl β-cyclodextrin hybrid monolithic material as adsorbent for dispersive solid-phase extraction of fluoroquinolones from environmental water samples

In this study, the hydroxypropyl β-cyclodextrin hybrid monolithic material was fabricated and firstly applied as adsorbent for dispersive solid-phase extraction coupled with high-performance liquid chromatography to detect trace-level seven fluoroquinolones in water samples. The prepared hydroxypropyl β-cyclodextrin hybrid monolithic material was characterized by fourier transform infrared spectroscopy, scanning electron microscopy and adsorption experiments, which showed excellent specific adsorption to the target fluoroquinolones. Under the optimized conditions, the extraction methodology showed satisfactory precision with relative standard deviations between 2.6 and 5.6%, good linearity (R² ≥0.9990) and satisfactory recoveries (82.5∼91.8%). The limits of detection and limits of quantification of the method were in the range of 0.4∼1.2 ng mL^-1 and 1.4∼4.0 ng mL^-1 respectively, which confirmed the possibility of quantifying trace levels. Furthermore, the material could be reused at least five times. These results demonstrated that the hydroxypropyl β-cyclodextrin hybrid monolithic material was a promising adsorbent for fluoroquinolones, and the established method combined dispersive solid-phase extraction with high-performance liquid chromatography was suitable for the determination of fluoroquinolones in aqueous samples. This article is protected by copyright. All rights reserved.

Simultaneous determination of the four key fluoroquinolones and two antipsychotics in fish and shrimp by LC-MS/MS

In this study, we developed and validated a liquid chromatography triple quadrupole tandem mass spectrometry (LC-MS/MS) method used to simultaneously determine levels of four fluoroquinolones (ofloxacin, norfloxacin, lomefloxacin, and pefloxacin) and two antipsychotics (diazepam and methaqualone) in fish and shrimp. The samples were extracted with a mixture of anhydrous sodium sulfate and acetonitrile, and purified by C₁₈ cartridge solid-phase extraction with an optimized eluent. The MS² method was applied to recognize the molecular structure of these compounds according to a main fragmentation scheme. The key ions of identification and quantification were deduced from chemical structures. Multiple reaction monitoring was used to quantitatively analyse the compounds of interest. Satisfactory linearities were obtained (R² ≥0.99) with the limits of quantitation (LOQs) ranging between 0.03 and 1.96 μg kg^-1. The recoveries were 74-122%, with a relative standard deviation (RSD) below 4.9% for these compounds at the spiking level of three, five, and ten times the LODs, respectively. The LC-MS/MS method allows precise and sensitive determination of residues of six important banned veterinary drugs in fish and shrimp tissue. This methodological approach solved the problem imposed by the need for two or more analysis methods to analyse the compounds of interest described in this study.

Design, Preparation, and Application of Magnetic Nanoparticles for Food Safety Analysis: A Review of Recent Advances

This review (with 126 references) aims at providing an updated overview of the recent developments and innovations of the preparation and application of magnetic nanoparticles for food safety analysis. During the past two decades, various magnetic nanoparticles with different sizes, shapes, and surface modifications have been designed, synthesized, and characterized with the prospering development of material science. Analytical scientists and food scientists are among the ones who bring these novel materials from laboratories to commercial applications. Powerful and versatile surface functional groups and high surface to mass ratios make these magnetic nanoparticles useful tools for high-efficiency capture and preconcentration of certain molecules, even when they exist in trace levels or complicated food matrices. This is why more and more methods for sensitive detection and quantification of hazards in foods are developed based on these magic magnetic tools. In this review, the principles and superiorities of using magnetic nanoparticles for food pollutant analysis are first introduced, like the mechanism of magnetic solid phase extraction, a most commonly used method for food safety-related sample pretreatment. Their design and preparation are presented afterward, alongside the mechanisms underlying their application for different analytical purposes. After that, recently developed magnetic nanoparticle-based methods for dealing with food pollutants such as organic pollutants, heavy metals, and pathogens in different food matrices are summarized in detail. In the end, some humble outlooks on future directions for work in this field are provided.