1
|
Nourishirazi R, Moradkhani G, SharafatVaziri A, Nematy H, Shayan-Moghadam R, Karimpour M. Biomechanical study of using patient-specific diaphyseal femoral cone in revision total knee arthroplasty (rTKA). J Orthop 2024; 57:65-71. [PMID: 38983674 PMCID: PMC11228766 DOI: 10.1016/j.jor.2024.06.002] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 04/21/2024] [Accepted: 06/01/2024] [Indexed: 07/11/2024] Open
Abstract
Background The primary objective of revision total knee surgery is to achieve solid bone fixation. Generally, this could be accomplished using sleeves and long stems, which require substantial remaining bone stock and may increase the risk of stem tip pain. An alternative approach involves the use of customized diaphyseal cones, which can preserve the integrity of the bone canal. This study evaluates the impact of employing femoral diaphyseal cones with various stem lengths on stress distribution and relative motion. Methods CT scan data from five patients were used to generate the 3D model of the femur, cement, customized stems, and cones, along with assigning patient-specific material for each candidate's femur. Three different stem lengths, both with and without the customized cone, were assessed under three gait loading conditions to compare the resulting Von Mises stress distribution and relative motion. Results Analysis indicated that the use of customized femoral cones moderately increases stress distribution values up to 30 % while significantly reducing relative motion at the femoral canal-cone interface by nearly 60 %. The presence of the cone did not significantly alter relative motion with varying stem lengths, although stem length variation without a cone substantially affected these values. Conclusion Incorporating cones alongside stems enhances metaphyseal fixation, reduces stress shielding, potentially allowing for the use of shorter stems. Furthermore, cones promote osseointegration by minimizing relative motion, ultimately improving prosthetic stability.
Collapse
Affiliation(s)
- Reza Nourishirazi
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| | - Ghazaleh Moradkhani
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| | - Arash SharafatVaziri
- Center for Orthopedic Trans-Disciplinary Applied Research (COTAR), Tehran University of Medical Sciences, Tehran, Iran
| | - Hamidreza Nematy
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| | - Ramin Shayan-Moghadam
- Center for Orthopedic Trans-Disciplinary Applied Research (COTAR), Tehran University of Medical Sciences, Tehran, Iran
| | - Morad Karimpour
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| |
Collapse
|
2
|
Khan Y, Arora S, Kashyap A, Patralekh MK, Maini L. Bone defect classifications in revision total knee arthroplasty, their reliability and utility: a systematic review. Arch Orthop Trauma Surg 2023; 143:453-468. [PMID: 35780426 DOI: 10.1007/s00402-022-04517-y] [Citation(s) in RCA: 3] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 12/14/2021] [Accepted: 06/12/2022] [Indexed: 02/02/2023]
Abstract
BACKGROUND There are various classification systems described in the literature for managing bone defects in revision knee arthroplasty (RTKA). We analysed the reliability and usefulness of these classification systems. QUESTIONS/PURPOSES (1) To review and critique the various classification systems proposed for bone loss in RTKA. (2) Among all the proposed classifications which one is the most commonly used by surgeons to report their results. (3) What is the reliability of various bone defect classification systems for RTKA. In this review, we have assessed the studies validating those classifications with a detailed description of the limitations and the proposed modifications. METHODS This systematic review was conducted following PRISMA guidelines. Pubmed/Medline, CINAHL, EMBASE, Scopus, Cochrane databases and Web of Science databases were searched using multiple search terms and MeSH terms where possible. Studies meeting inclusion criteria were assessed for statistical parameters of reliability of a classification system. RESULTS We found 16 classification systems for bone defects in RTKA. Six studies were found evaluating a classification system with reporting their reliability parameters. Fifty-four studies were found which classified bone loss using AORI classification in their series. AORI classification is most commonly reported for classifying bone defects. Type T2B and F2B are the most common bone defects in RTKA. The average kappa value for AORI classification for femoral bone loss was 0.38 (0.27-0.50) and 0.76 (0.63-1) for tibial bone loss assessment. CONCLUSION None of the available classification systems is reliably established in determining the bone loss and treatment plans in RTKA. Among all, AORI classification is the most widely used system in clinical practice. The reliability of AORI Classification is fair for femoral bone loss and substantial for tibial bone loss.
Collapse
Affiliation(s)
- Yasim Khan
- Department of Orthopaedic Surgery, Maulana Azad Medical College and Lok Nayak Hospital, New Delhi, 110002, India. .,, New Delhi, India.
| | - Sumit Arora
- Department of Orthopaedic Surgery, Maulana Azad Medical College and Lok Nayak Hospital, New Delhi, 110002, India
| | - Abhishek Kashyap
- Department of Orthopaedic Surgery, Maulana Azad Medical College and Lok Nayak Hospital, New Delhi, 110002, India
| | | | - Lalit Maini
- Department of Orthopaedic Surgery, Maulana Azad Medical College and Lok Nayak Hospital, New Delhi, 110002, India
| |
Collapse
|
3
|
Liu Y, Chen B, Wang C, Chen H, Zhang A, Yin W, Wu N, Han Q, Wang J. Design of Porous Metal Block Augmentation to Treat Tibial Bone Defects in Total Knee Arthroplasty Based on Topology Optimization. Front Bioeng Biotechnol 2021; 9:765438. [PMID: 34820364 PMCID: PMC8606634 DOI: 10.3389/fbioe.2021.765438] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/27/2021] [Accepted: 10/04/2021] [Indexed: 11/13/2022] Open
Abstract
Metal block augmentation, which is used for the treatment of tibial bone defects in total knee arthroplasty, with high stiffness will cause significant alteration in stress distribution, and its solid structure is not suitable for osseointegration. This study aimed to design a porous block to reduce weight, promote bone ingrowth, and improve its biomechanical performance. The metal block augmentation technique was applied to finite element models of tibial bone defects. Minimum compliance topology optimization subject to volume fraction combined with the porous architecture was adopted to redesign the block. Biomechanical changes compared with the original block were analyzed by finite element analysis. The stress distribution of the block and proximal tibia was recorded. The strain energy density of the proximal tibia was obtained. The newly designed block realized 40% weight reduction. The maximum stress in the optimized block decreased by 11.6% when compared with the solid one. The maximum stress of the proximal tibia in the optimized group increased by 18.6%. The stress of the anterior, medial, and posterior parts of the proximal medial tibia in the optimized group was significantly greater than that in the original group (all p < 0.05). The optimized block could effectively improve the biomechanical performance between the block and the bone. The presented method might provide a reference for the design of customized three-dimensional printed prostheses.
Collapse
Affiliation(s)
- Yang Liu
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Bingpeng Chen
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Chenyu Wang
- Department of Plastic and Reconstructive Surgery, First Bethune Hospital of Jilin University, Changchun, China
| | - Hao Chen
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Aobo Zhang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Weihuang Yin
- Department of Oral and Maxillofacial Surgery, Hospital of Stomatology, Jilin University, Changchun, China
| | - Naichao Wu
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Qing Han
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Jincheng Wang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| |
Collapse
|
4
|
Kremer M, Gramlich Y, Hoffmann R. [Revision Total Knee Arthroplasty]. ZEITSCHRIFT FUR ORTHOPADIE UND UNFALLCHIRURGIE 2020; 159:565-582. [PMID: 32998164 DOI: 10.1055/a-1149-9654] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 10/23/2022]
Abstract
In addition to periprosthetic infections (PJI), the reconstruction of bony defects is the major challenge of revision total knee arthroplasty (TKA). Infection should be ruled out in all cases prior to operation. Revision TKA requires intensive planning with regard to the needed augmentation possibilities and the stems to be used. The sole biological reconstruction of major defects (AORI II and III) shows high failure rates. Large defects must be augmented by metal (wedges/sleeves/cones). The concept of zonal anchorage (3-zone model) with a stable anchorage in 2 out of 3 zones as close to the joint as possible is currently the standard. According to the model, metaphysis (zone 2) is an increasingly important factor for long-term stable anchoring. The use of cones or sleeves seems to significantly improve the results of revision TKA. The anchorage in zone 3 via stems is still mandatory. Cemented metaphysary anchoring and cement-free diaphysary anchoring stems are available, whereby no clear recommendation for a principle can be given.
Collapse
|
5
|
Liu Y, Zhang A, Wang C, Yin W, Wu N, Chen H, Chen B, Han Q, Wang J. Biomechanical comparison between metal block and cement-screw techniques for the treatment of tibial bone defects in total knee arthroplasty based on finite element analysis. Comput Biol Med 2020; 125:104006. [PMID: 32971324 DOI: 10.1016/j.compbiomed.2020.104006] [Citation(s) in RCA: 10] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/02/2020] [Revised: 08/30/2020] [Accepted: 08/31/2020] [Indexed: 02/07/2023]
Abstract
BACKGROUND Managing bone defects is a critical aspect of total knee arthroplasty. In this study, we compared the metal block and cement-screw techniques for the treatment of Anderson Orthopaedic Research Institute type 2A tibial bone defects from the biomechanical standpoint. METHOD The metal block and cement-screw techniques were applied to finite element models of 5- and 10-mm tibial bone defects. Biomechanical compatibility was evaluated based on the stress distributions of the proximal tibia and tibial tray. The displacement of the tibial tray and maximum relative micromotion between the tibial stem and tibia were analyzed to assess the stability of the implant. RESULTS The maximum stress in both the proximal tibia and tibial tray was greater with the cement-screw technique than with the metal block technique. The stress of the proximal lateral tibia with the cement-screw technique was significantly larger than with the metal block technique (p < 0.05). For the 5-mm bone defect, the maximum relative micromotion was lower than the critical value of 150 μm. For the 10-mm defect, the maximum relative micromotion was 128 μm with the metal block technique and 155 μm with the cement-screw technique, with the latter exceeding the critical value. CONCLUSIONS The cement-screw technique showed superior biomechanical compatibility to the metal block technique and is more suitable for 5-mm bone defects. However, as it may reduce the fixation strength in 10-mm bone defects, the metal block technique is more appropriate in this case.
Collapse
Affiliation(s)
- Yang Liu
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, China.
| | - Aobo Zhang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, China.
| | - Chenyu Wang
- Department of Plastic and Reconstructive Surgery, First Bethune Hospital of Jilin University, Changchun, 130021, China.
| | - Weihuang Yin
- Department of Oral and Maxillofacial Surgery, Hospital of Stomatology, Jilin University, Changchun, 130021, China.
| | - Naichao Wu
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, China.
| | - Hao Chen
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, China.
| | - Bingpeng Chen
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, China.
| | - Qing Han
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, China.
| | - Jincheng Wang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, China.
| |
Collapse
|
6
|
Awadalla M, Al-Dirini RMA, O'Rourke D, Solomon LB, Heldreth M, Rullkoetter P, Taylor M. Influence of stems and metaphyseal sleeve on primary stability of cementless revision tibial trays used to reconstruct AORI IIB defects. J Orthop Res 2019; 37:1033-1041. [PMID: 30677164 DOI: 10.1002/jor.24232] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 06/03/2018] [Accepted: 01/08/2019] [Indexed: 02/04/2023]
Abstract
Metaphyseal augments, such as sleeves, have been introduced to augment the fixation of revision total knee replacement (rTKR) components, and can be used with or without a stem. The effect of sleeve size in combination with stems on the primary stability and load transfer of a rTKR implant in AORI type IIB defects where the defect involves both condyles are poorly understood. The aim of this study was to examine the primary stability of revision tibial tray augmented with a sleeve in an AORI type IIB defect which involves both condyles with loss of cortical and cancellous bone. Finite element models were generated from computed tomography (CT) scans of nine individuals. All the bones used in the study had an AORI type IIB defect. The cohort included eight females (mean weight: 64 kg, height: 1.6 m). Material properties were sampled from CT data and assigned to the FE model. Joint contact forces for level gait, stair descent, and squat were applied. Stemless sleeved implants under various loading conditions were shown to have adequate primary stability in all AORI type IIB defects investigated. Adding a stem only marginally improved the primary stability of the implant but reduced the strain in the metaphysis compared to stemless implants. Once good initial mechanical stability was established with a sleeve, there was no benefit, in terms of primary stability or bone strains, from increasing sleeve size. This study suggests that metaphyseal sleeves, without a stem, can provide the required primary stability required by a rTKR tibial implant, to reconstruct an AORI type IIB defect. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res.
Collapse
Affiliation(s)
- Maged Awadalla
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| | - Rami M A Al-Dirini
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| | - Dermot O'Rourke
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| | - Lucian B Solomon
- Department of Orthopaedics and Trauma, Royal Adelaide Hospital, SA, Australia.,The University of Adelaide, Centre for Orthopaedic and Trauma Research, SA, Australia
| | - Mark Heldreth
- DePuy Synthes Inc., Joint Reconstruction, Warsaw, Indiana
| | - Paul Rullkoetter
- Department of Mechanical and Materials Engineering, University of Denver, Denver, Colorado
| | - Mark Taylor
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| |
Collapse
|
7
|
Melo D, Completo A, Nascimento A, Fonseca F. Biomechanical analysis of metacarpophalangeal joint arthroplasty with metal-polyethylene implant: An in-vitro study. Clin Biomech (Bristol, Avon) 2019; 62:79-85. [PMID: 30710796 DOI: 10.1016/j.clinbiomech.2019.01.005] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 10/31/2018] [Revised: 01/16/2019] [Accepted: 01/21/2019] [Indexed: 02/07/2023]
Abstract
BACKGROUND The most common implant options for the metacarpophalangeal joint arthroplasty include silicone, pyrocarbon and metal-polyethylene. A systematic review of outcomes of silicone and pyrocarbon implants was conducted; however, a similar exercise for metal-polyethylene implants revealed a scarcity of published results and lack of long-term follow-up studies. The aim of the present work is to test the hypothesis that the magnitude of metacarpophalangeal joint cyclic loads generates stress and strain behaviour, which leads to long-term reduced risk of metal-polyethylene component loosening. METHODS This study was performed using synthetic metacarpals and proximal phalanges to experimentally predict the cortex strain behaviour for both intact and implanted states. Finite element models were developed to assess the structural behaviour of cancellous-bone and metal-polyethylene components; these models were validated by comparing cortex strains predictions against the measurements. FINDINGS Cortex strains in the implanted metacarpophalangeal joint presented a significant reduction in relation to the intact joint; the exception was the dorsal side of the phalanx, which presents a significant strain increase. Cancellous-bone at proximal dorsal region of phalanx reveals a three to fourfold strain increase as compared to the intact condition. Interpretation The use of metal-polyethylene implant changes the strain behaviour of the metacarpophalangeal joint yielding the risk of cancellous-bone fatigue failure due to overload in proximal phalanx; this risk is more important than the risk of bone-resorption due to the strain-shielding effect. By limiting the loads magnitude over the joint after arthroplasty, it may contribute to the prevention of implant loosening.
Collapse
Affiliation(s)
- D Melo
- Mechanical Engineering Department, University of Aveiro, Portugal
| | - A Completo
- Mechanical Engineering Department, University of Aveiro, Portugal.
| | - A Nascimento
- Orthopaedics Department, Coimbra University Hospital, Portugal
| | - F Fonseca
- Orthopaedics Department, Coimbra University Hospital, Portugal
| |
Collapse
|
8
|
Innocenti B, Fekete G, Pianigiani S. Biomechanical Analysis of Augments in Revision Total Knee Arthroplasty. J Biomech Eng 2018; 140:2694847. [PMID: 30098138 DOI: 10.1115/1.4040966] [Citation(s) in RCA: 10] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/09/2018] [Indexed: 11/08/2022]
Abstract
Augments are a common solution for treating bone loss in revision total knee arthroplasty and industry is providing to surgeons several options, in terms of material, thickness and shapes. Actually, while the choice of the shape and the thickness is mainly dictated by the bone defect, no proper guidelines are currently available to select the optimal material for a specific clinical situation. Nevertheless, different materials could induce different bone responses and, later, potentially compromise implant stability and performances. Therefore, in this study, a biomechanical analysis is performed by means of finite element modelling about existing features for augment designs. Based upon a review of available products at present, the following augments features were analyzed: position (distal/proximal and posterior), thickness (5, 10 and 15 mm) and material (bone cement, porous and solid metal). For all analyzed configurations, bone stresses were investigated in different regions and compared among all configurations and the control model for which no augments were used. Results show that the use of any kind of augment usually induces a change in bone stresses, especially in the region close to the bone cut. The porous metal presents result very close to cement ones; thus it could be considered as a good alternative for defects of any size. Solid metal has the least satisfying results inducing the highest changes in bone stress. The results of this study demonstrate that material stiffness of the augment should be as close as possible to bone properties for allowing the best implant performances.
Collapse
Affiliation(s)
- Bernardo Innocenti
- BEAMS Department, Université Libre De Bruxelles, Av. F. Roosevelt, 50 CP165/56, 1050 Bruxelles, Belgium
| | - Gusztáv Fekete
- Savaria Institute of Technology, Faculty of Informatics, Eötvös Loránd University, Károlyi Gáspár 4, 9700 Szombathely, Hungary
| | - Silvia Pianigiani
- BEAMS Department, Université Libre De Bruxelles, Av. F. Roosevelt, 50 CP165/56, 1050 Bruxelles, Belgium
| |
Collapse
|
9
|
Completo A, Nascimento A, Girão AF, Fonseca F. Biomechanical evaluation of pyrocarbon proximal interphalangeal joint arthroplasty: An in-vitro analysis. Clin Biomech (Bristol, Avon) 2018; 52:72-78. [PMID: 29407860 DOI: 10.1016/j.clinbiomech.2018.01.005] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 09/06/2017] [Revised: 12/20/2017] [Accepted: 01/14/2018] [Indexed: 02/07/2023]
Abstract
BACKGROUND Pyrocarbon proximal interphalangeal joint arthroplasty provided patients with excellent pain relief and joint motion, however, overall implant complications have been very variable, with some good outcomes at short-medium-term follow-up and some bad outcomes at longer-term follow-up. Implant loosening with migration, dislocation and implant fracture were the main reported clinical complications. The aim of the present work was to test the hypothesis that the magnitude proximal interphalangeal joint cyclic loads in daily hand functions generates stress-strain behaviour which may be associated with a risk of pyrocarbon component loosening in the long-term. METHODS This study was performed using synthetic proximal and middle phalanges to experimentally predict the cortex strain behaviour and implant stability considering different load conditions for both intact and implanted states. Finite element models were developed to assess the structural behaviour of cancellous-bone and pyrocarbon components, these models were validated against experimentally measured cortex strains. FINDINGS Cortex strains showed a significant increase at dorsal side and reduction at palmar side between intact and implanted states. Cancellous-bone adjacent to the condylar implant base components suffers a two to threefold strain increase, comparing with the intact condition. INTERPRETATION The use of pyrocarbon implant changes the biomechanical behaviour of the joint phalanges and is associated with a potential risk of support cancellous-bone suffer fatigue failure in mid to long term due to the strain increase for cyclic loads in the range of daily hand activities, this risk is more prominent than the risk of bone resorption due to strain-shielding effect.
Collapse
Affiliation(s)
- A Completo
- Mechanical Engineering Department, University of Aveiro, Portugal.
| | - A Nascimento
- Orthopaedics Department, Coimbra University Hospital, Portugal
| | - A F Girão
- Mechanical Engineering Department, University of Aveiro, Portugal
| | - F Fonseca
- Orthopaedics Department, Coimbra University Hospital, Portugal
| |
Collapse
|
10
|
Completo A, Fonseca F, Ramos A, Simões J. Comparative assessment of different reconstructive techniques of distal femur in revision total knee arthroplasty. Knee Surg Sports Traumatol Arthrosc 2017; 25:2559-2566. [PMID: 26025074 DOI: 10.1007/s00167-015-3652-2] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 12/10/2014] [Accepted: 05/18/2015] [Indexed: 10/23/2022]
Abstract
PURPOSE Bone loss is often encountered in revision total knee arthroplasty. In particular, when the cortex of distal femur is breached, the surgical decision on the reconstructive options to be taken is challenging due to the variety of defects and the lack of data from clinical or experimental studies that can support it. The aim of the present work was to test the hypothesis that for an identical defect and bone condition, each reconstructive technique option has a dissimilar stress and stability behaviour, which may be related to differing longevity of the revision procedure. METHODS Triaxial strain gauges and video extensometer were used to measure distal cortex strains and implant stability in eight reconstructive techniques replicated with synthetic femur under a load of 2030N. To assess the cancellous bone strains, finite element models were developed and validated. RESULTS The measured strains showed that the distal cortex is not immune to the different reconstructive techniques, when applied to an identical defect; however, significant differences (P < 0.05) were found only between bone graft and metal augment on the 12-mm larger distal defect. The stem addition improves the stability of all reconstructive techniques; however, significant differences (P = 0.03) were found only on the bone-graft technique. CONCLUSIONS Cement-fill and metal-augment techniques, applied to the 4-mm smaller defect, are not associated with different structural behaviour, while for the 12-mm larger defect, the metal-augment and bone-graft techniques presented distinct biomechanical effects. These effects, by themselves, may not be sufficient to be associated with a different longevity of the revision procedure among techniques, when the stem is added to the bone-graft technique. These findings, based on independent scientific understanding and advanced prediction tools, can improve the surgical decision-making process, when the peripheral cortex of the distal femur is breached.
Collapse
Affiliation(s)
- A Completo
- Department of Mechanical Engineering, University of Aveiro, 3810-193, Aveiro, Portugal.
| | - F Fonseca
- Department of Orthopaedics, Coimbra University Hospital, 3000-075, Coimbra, Portugal
| | - A Ramos
- Department of Mechanical Engineering, University of Aveiro, 3810-193, Aveiro, Portugal
| | - J Simões
- Department of Mechanical Engineering, University of Aveiro, 3810-193, Aveiro, Portugal
| |
Collapse
|
11
|
Chen TL, An WW, Chan ZYS, Au IPH, Zhang ZH, Cheung RTH. Immediate effects of modified landing pattern on a probabilistic tibial stress fracture model in runners. Clin Biomech (Bristol, Avon) 2016; 33:49-54. [PMID: 26945721 DOI: 10.1016/j.clinbiomech.2016.02.013] [Citation(s) in RCA: 26] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 10/20/2015] [Revised: 02/12/2016] [Accepted: 02/17/2016] [Indexed: 02/07/2023]
Abstract
BACKGROUND Tibial stress fracture is a common injury in runners. This condition has been associated with increased impact loading. Since vertical loading rates are related to the landing pattern, many heelstrike runners attempt to modify their footfalls for a lower risk of tibial stress fracture. Such effect of modified landing pattern remains unknown. This study examined the immediate effects of landing pattern modification on the probability of tibial stress fracture. METHODS Fourteen experienced heelstrike runners ran on an instrumented treadmill and they were given augmented feedback for landing pattern switch. We measured their running kinematics and kinetics during different landing patterns. Ankle joint contact force and peak tibial strains were estimated using computational models. We used an established mathematical model to determine the effect of landing pattern on stress fracture probability. FINDINGS Heelstrike runners experienced greater impact loading immediately after landing pattern switch (P<0.004). There was an increase in the longitudinal ankle joint contact force when they landed with forefoot (P=0.003). However, there was no significant difference in both peak tibial strains and the risk of tibial stress fracture in runners with different landing patterns (P>0.986). INTERPRETATION Immediate transitioning of the landing pattern in heelstrike runners may not offer timely protection against tibial stress fracture, despite a reduction of impact loading. Long-term effects of landing pattern switch remains unknown.
Collapse
Affiliation(s)
- T L Chen
- Gait & Motion Analysis Laboratory, Department of Rehabilitation Sciences, The Hong Kong Polytechnic University, Hong Kong
| | - W W An
- Gait & Motion Analysis Laboratory, Department of Rehabilitation Sciences, The Hong Kong Polytechnic University, Hong Kong
| | - Z Y S Chan
- Gait & Motion Analysis Laboratory, Department of Rehabilitation Sciences, The Hong Kong Polytechnic University, Hong Kong
| | - I P H Au
- Gait & Motion Analysis Laboratory, Department of Rehabilitation Sciences, The Hong Kong Polytechnic University, Hong Kong
| | - Z H Zhang
- Gait & Motion Analysis Laboratory, Department of Rehabilitation Sciences, The Hong Kong Polytechnic University, Hong Kong
| | - R T H Cheung
- Gait & Motion Analysis Laboratory, Department of Rehabilitation Sciences, The Hong Kong Polytechnic University, Hong Kong.
| |
Collapse
|
12
|
Graichen H, Strauch M, Scior W, Morgan-Jones R. [Knee revision arthroplasty : cementless, metaphyseal fixation with sleeves]. OPERATIVE ORTHOPADIE UND TRAUMATOLOGIE 2015; 27:24-34. [PMID: 25620192 DOI: 10.1007/s00064-014-0333-0] [Citation(s) in RCA: 13] [Impact Index Per Article: 1.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/16/2014] [Revised: 09/08/2014] [Accepted: 09/10/2014] [Indexed: 01/17/2023]
Abstract
OBJECTIVE Primary and long-term fixation of cementless metaphyseal implants in knee revision arthroplasty cases with large bone defects. INDICATIONS All tibial and femoral bone defects AORI grade 2 and 3. CONTRAINDICATIONS Cases where stable uncemented fixation of the metaphyseal implant is not possible. SURGICAL TECHNIQUE Pre-operative evaluation of the failure mode and implant fixation planning. After opening the joint, a synovectomy and mobilisation of medial and lateral recesses routinely performed. Testing of ligamentous stability and implant fixation undertaken before explantation. Removal of the bearing, femoral and tibial components with osteotomes or oscillating saw. Tibial diaphysis prepared with reamers, and metaphyseal preparation with broaches and stem extension. Placement of the metaphyseal broach for height with respect to the tibial joint line and rotational stability assessed. Tibial tray size and position determined before implanting the sleeve, stem and tray trial. The tibial trial provides a stable platform for analysis of the extension and flexion gaps with spacer blocks. Diaphyseal reamers used to identify the anterior femoral bow. Metaphyseal broaches used to achieve stable fixation up to the resection line marked on the handle. Distal femoral freshening cut in 5° or 7° of valgus made to accommodate distal augments as needed. Positioning of the 4-in-1 block with reconstruction of the posterior off-set and cutting for posterior augmentation. Selection of a box cut corresponding to the amount of constraint needed. Trial insert with appropriate, stem, sleeve, condylar femur and augments introduced. Bearing size, joint stability and ROM assessed. Patella alignment and the need for patella replacement or revision determined. The definitive implants are cemented at the joint surface, with metaphyseal sleeves and diaphyseal stems are uncemented. POSTOPERATIVE MANAGEMENT Full weight bearing as tolerated, physiotherapy, lymph drainage and pain therapy are routine with no specific post-operative management required. RESULTS Between 2007 and 2011, 193 sleeves (119 tibial/74 femoral) were implanted in 121 aspetic knee revision arthroplasties. After average of 3.6 years they were analysed clinically and radiographically. The AKSS (American Knee Society Score) increased from 88 ± 18 to 147 ± 23 points (p < 0.01). ROM (range of motion) increased from 89 ± 6° to 114 ± 4°. Overall revision rate was 11.6 %. Only 4 sleeves revised for aseptic loosening (2 % of total sleeves). An additional 10 revisions performed mainly for infection (3.3 %) or ligament instability (3.3 %).
Collapse
Affiliation(s)
- H Graichen
- Endoprothetik - Zentrum, Asklepios Orthopädische Klinik Lindenlohe, Lindenlohe 18, 92421, Schwandorf, Deutschland,
| | | | | | | |
Collapse
|
13
|
Duarte RJ, Ramos A, Mesnard M. The influence of disc wear on the behavior of the temporomandibular joint: a finite element analysis in a specific case. ACTA ACUST UNITED AC 2014. [DOI: 10.12989/aba.2014.1.3.159] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/22/2022]
|
14
|
Zach L, Kunčická L, Růžička P, Kocich R. Design, analysis and verification of a knee joint oncological prosthesis finite element model. Comput Biol Med 2014; 54:53-60. [PMID: 25212118 DOI: 10.1016/j.compbiomed.2014.08.021] [Citation(s) in RCA: 19] [Impact Index Per Article: 1.9] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/12/2014] [Revised: 08/16/2014] [Accepted: 08/17/2014] [Indexed: 11/28/2022]
Abstract
BACKGROUND The aim of this paper was to design a finite element model for a hinged PROSPON oncological knee endoprosthesis and to verify the model by comparison with ankle flexion angle using knee-bending experimental data obtained previously. METHOD Visible Human Project CT scans were used to create a general lower extremity bones model and to compose a 3D CAD knee joint model to which muscles and ligaments were added. Into the assembly the designed finite element PROSPON prosthesis model was integrated and an analysis focused on the PEEK-OPTIMA hinge pin bushing stress state was carried out. To confirm the stress state analysis results, contact pressure was investigated. The analysis was performed in the knee-bending position within 15.4-69.4° hip joint flexion range. RESULTS The results showed that the maximum stress achieved during the analysis (46.6 MPa) did not exceed the yield strength of the material (90 MPa); the condition of plastic stability was therefore met. The stress state analysis results were confirmed by the distribution of contact pressure during knee-bending. CONCLUSION The applicability of our designed finite element model for the real implant behaviour prediction was proven on the basis of good correlation of the analytical and experimental ankle flexion angle data.
Collapse
Affiliation(s)
- Lukáš Zach
- Department of Mechanics, Biomechanics and Mechatronics, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technická 4, 166 07 Praha 6, Czech Republic
| | - Lenka Kunčická
- Department of Materials Forming, Faculty of Metallurgy and Materials Engineering, VŠB-TU Ostrava, 17. listopadu 15, Ostrava-Poruba 70833, Czech Republic; Regional Materials Science and Technology Centre, VŠB-TU Ostrava, 17. listopadu 15, Ostrava-Poruba 70833, Czech Republic.
| | - Pavel Růžička
- Department of Mechanics, Biomechanics and Mechatronics, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technická 4, 166 07 Praha 6, Czech Republic
| | - Radim Kocich
- Department of Materials Forming, Faculty of Metallurgy and Materials Engineering, VŠB-TU Ostrava, 17. listopadu 15, Ostrava-Poruba 70833, Czech Republic; Regional Materials Science and Technology Centre, VŠB-TU Ostrava, 17. listopadu 15, Ostrava-Poruba 70833, Czech Republic
| |
Collapse
|
15
|
Dao TT, Rassineux A, Charleux F, Ho Ba Tho MC. A robust protocol for the creation of patient-specific finite element models of the musculoskeletal system from medical imaging data. COMPUTER METHODS IN BIOMECHANICS AND BIOMEDICAL ENGINEERING-IMAGING AND VISUALIZATION 2014. [DOI: 10.1080/21681163.2014.896226] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 10/25/2022]
|