Development, validation, and application of ligamentous cervical spinal segment C6-C7 of a six-year-old child and an adult

Finite Element Modelling of a Synthetic Paediatric Spine for Biomechanical Investigation

Studies on paediatric spines commonly use human adult or immature porcine spines as specimens, because it is difficult to obtain actual paediatric specimens. There are quite obvious differences, such as geometry, size, bone morphology, and orientation of facet joint for these specimens, compared to paediatric spine. Hence, development of synthetic models that can behave similarly to actual paediatric spines, particularly in term of range of motion (ROM), could provide a significant contribution for paediatric spine research. This study aims to develop a synthetic paediatric spine using finite element modelling and evaluate the reliability of the model by comparing it with the experimental data under certain load conditions. The ROM of the paediatric spine was measured using a validated FE model at ±0.5 Nm moment in order to determine the moment required by the synthetic spine to achieve the same ROM. The results showed that the synthetic spine required two moments, ±2 Nm for lateral-bending and axial rotation, and ±3 Nm for flexion-extension, to obtain the paediatric ROM. The synthetic spine was shown to be stiffer in flexion-extension but more flexible in lateral bending than the paediatric FE model, possibly as a result of the intervertebral disc's simplified shape and the disc's weak bonding with the vertebrae. Nevertheless, the synthetic paediatric spine has promising potential in the future as an alternative paediatric spine model for biomechanical investigation of paediatric cases.

Kinematic and biomechanical responses of the spine to distraction surgery in children with early onset scoliosis: A 3-D finite element analysis

Periodical and consecutive distraction is an effective treatment for severe early onset scoliosis (EOS), which enables the spinal coronal and sagittal plane deformity correction. However, the rate of rod fractures and postoperative complications was still high mainly related to the distraction process. Previous studies have primarily investigated the maximum safe distraction force without a rod broken, neglecting the spinal re-imbalance and distraction energy consumption, which is equally vital to evaluate the operative value. This study aimed to reveal the kinematic and biomechanical responses occurring after spinal distraction surgery, which were affected by traditional bilateral fixation. The spinal models (C6-S1) before four distractions were reconstructed based on CT images and the growing rods were applied with the upward displacement load of 0–25 mm at an interval of 5 mm. Relationships between the distraction distance, the distraction force and the thoracic and lumbar Cobb angle were revealed, and the spinal displacement and rotation in three-dimensional directions were measured. The spinal overall imbalance would also happen during the distraction process even under the safe force, which was characterized by unexpected cervical lordosis and lateral displacement. Additionally, the law of diminishing return has been confirmed by comparing the distraction energy consumption in different distraction distances, which suggests that more attention paid to the spinal kinematic and biomechanical changes is better than to the distraction force. Notably, the selection of fixed segments significantly impacts the distraction force at the same distraction distance. Accordingly, some results could provide a better understanding of spinal distraction surgery.

Finite Element Analysis and Comparative Study of 4 Kinds of Internal Fixation Systems for Anterior Cervical Discectomy and Fusion in Children

Background

Spinal injury in children usually occurs in the cervical spine region. Anterior fixation of the lower cervical spine has been applied in treating pediatric cervical spine injury and disease due to its stable and firm mechanical properties. This study performed finite element analysis and comparison of four different anterior cervical internal fixation systems for children to explore more standard methods of anterior cervical internal fixation in children and seek more effective and safe treatment for children's cervical spine diseases.

Methods

A finite element model of 6-year-old children with lower cervical spine C4/5 discectomy was established, and the self-designed lower cervical spine anterior locking internal fixation system ACBLP and the children's anterior cervical internal fixation system ACOP, ACVLP, and ACSLP plate screws were fixed and loaded on the model. 27.42 N·m torque load was applied to each internal fixation model under six working conditions of anteflexion, backward flexion, left flexion, right flexion, left rotation, and right rotation, to simulate the movement of the cervical spine. The activity and stress distribution cloud diagram of each finite element model was obtained to explore the optimal method of anterior cervical fixation in children.

Results

In the four internal fixation models of ACOP, ACVLP, ACSLP, and ACBLP, the mobility of the C4/5 segment showed a decreasing relationship, and the mobility of adjacent segments increased significantly. In the Mises stress cloud diagram of the cervical spine of the four models, the vertebral body and accessories of the ACBLP model born the least stress, followed by ACSLP. The steel plate and screws in the ACVLP internal fixation model were the most stressed. The stress of the internal fixation system (plate/screw) in all models increased in the order of ACBLP, ACSLP, ACVLP, and ACOP.

Conclusions

ACBLP internal fixation system had obvious advantages in anterior internal fixation of the lower cervical spine in children, C4/5 had the smallest degree of movement, relative displacement was minimal, and the stress on the centrum and pedicle was the least, while the stress on the plate screw was relatively the smallest.

Effects of Growing Rod Technique with Different Surgical Modes and Growth Phases on the Treatment Outcome of Early Onset Scoliosis: A 3-D Finite Element Analysis

Early onset scoliosis (EOS) is emerging as a serious threat to children’s health and is the third largest threat to their health after myopia and obesity. At present, the growing rod technique (GRT), which allows patients to regain a well-balanced sagittal profile, is commonly considered as an invasive surgical procedure for the treatment of EOS. However, the risk of postoperative complications and instrumentation breakage remains high, which is mainly related to the choice of fixed mode. Several authors have studied primary stability and instrumentation loads, neglecting the mechanical transmission of the spinal long-segment model in different growth phases, which is fundamental to building a complete biomechanical environment. The present study aimed to investigate the kinematic and biomechanical properties that occur after GRT, across the long spinal structure and the posterior instrumentation, which are affected by unilateral or bilateral fixation. Accordingly, spinal segments (C6-S1) were loaded under flexion (Flex), extension (Ext), left lateral bending (LB), right lateral bending (RB), left torsion (LT), and right torsion (RT) using 11 established spinal models, which were from three growth phases. The stress distribution, spinal and intervertebral range of motion (ROM), counter torque of the vertebra, and bracing force on the rods were measured. The results showed that bilateral posterior fixation (BPF) is more stable than unilateral posterior fixation (UPF), at the expense of more compensations for the superior adjacent segment (SAS), especially when the superior fixed segment is closer to the head. Additionally, the bracing force of the instrumentation on the spine increases as the Cobb angle decreases. Accordingly, this biomechanical analysis provides theoretical suggestions for the selection of BPF or UPF and fixed segments in different growing phases.

Estimation of a statistical geometric model for the cervical vertebrae of children aged 10-18 years

Child neck injuries in motor vehicle crashes (MVCs) result in high morbidity and mortality rates. Estimating a statistical cervical vertebrae geometric model and quantifying the variations of the size and shape with age are very important for investigating the dynamic response and injury risk to a child's cervical spine, as well as for providing a geometric basis for developing child anthropomorphic test devices (ATDs) and finite element models (FEMs) of different ages. In this study, spatial geometric points were automatically extracted from the cervical vertebrae computed tomography (CT) scans of 30 children aged 10 to 18 years old (YO), and a statistical geometric model was estimated for the cervical vertebrae as a function of age and neck circumference/neck length according to the method of principal component analysis and regression (PCA&R). Based on this statistical model, geometric point sets representing cervical vertebrae geometries at different ages and percentiles were generated and formed to envelope surfaces. Meanwhile, the size changes of the cervical vertebrae with child growth from 10 to 18 YO were quantified. In general, the anteroposterior length (APL), transverse process width (TPW), vertebral body height (VBH), and vertebral body depth (VBD) of the cervical vertebrae increase with age; the VBH and VBD increase faster than the APL and TPW. Compared with other vertebrae, the APL of C7 is larger, and the rate of increase of C1 with age is evidently slower. The TPWs of C1 and C7 are greater than those of C2 to C6. C7 has higher average values for the VBH and VBD than C3 to C6.