Dynamic contact angle beating from drops impacting onto solid surfaces exhibiting anisotropic wetting

Fog Collection on Polyethylene Terephthalate (PET) Fibers: Influence of Cross Section and Surface Structure

Fog-collecting meshes show a great potential in ensuring the availability of a supply of sustainable freshwater in certain arid regions. In most cases, the meshes are made of hydrophilic smooth fibers. Based on the study of plant surfaces, we analyzed the fog collection using various polyethylene terephthalate (PET) fibers with different cross sections and surface structures with the aim of developing optimized biomimetic fog collectors. Water droplet movement and the onset of dripping from fiber samples were compared. Fibers with round, oval, and rectangular cross sections with round edges showed higher fog-collection performance than those with other cross sections. However, other parameters, for example, width, surface structure, wettability, and so forth, also influenced the performance. The directional delivery of the collected fog droplets by wavy/v-shaped microgrooves on the surface of the fibers enhances the formation of a water film and their fog collection. A numerical simulation of the water droplet spreading behavior strongly supports these findings. Therefore, our study suggests the use of fibers with a round cross section, a microgrooved surface, and an optimized width for an efficient fog collection.

Hierarchical Surface Architecture of Plants as an Inspiration for Biomimetic Fog Collectors

Fog collectors can enable us to alleviate the water crisis in certain arid regions of the world. A continuous fog-collection cycle consisting of a persistent capture of fog droplets and their fast transport to the target is a prerequisite for developing an efficient fog collector. In regard to this topic, a biological superior design has been found in the hierarchical surface architecture of barley (Hordeum vulgare) awns. We demonstrate here the highly wettable (advancing contact angle 16° ± 2.7 and receding contact angle 9° ± 2.6) barbed (barb = conical structure) awn as a model to develop optimized fog collectors with a high fog-capturing capability, an effective water transport, and above all an efficient fog collection. We compare the fog-collection efficiency of the model sample with other plant samples naturally grown in foggy habitats that are supposed to be very efficient fog collectors. The model sample, consisting of dry hydrophilized awns (DH awns), is found to be about twice as efficient (fog-collection rate 563.7 ± 23.2 μg/cm(2) over 10 min) as any other samples investigated under controlled experimental conditions. Finally, a design based on the hierarchical surface architecture of the model sample is proposed for the development of optimized biomimetic fog collectors.

Minimum energy paths of wetting transitions on grooved surfaces

A method that computes minimum energy paths (MEPs) of wetting transitions is developed. The method couples the Cahn-Hilliard formulation of a modified phase-field method with the simplified string method. Its main computational kernel is the fast Fourier transform that is efficiently performed on graphics processing units. The effectiveness of the proposed method is demonstrated on two types of transitions of droplets on grooved surfaces. The first is the transition from the Cassie-Baxter wetting state to the Wenzel state, where it is shown that it progresses in a sequential manner with the droplet wetting each groove successively. The second transition type is a lateral displacement of the droplet against the grooves, where the droplet successively detaches/attaches from/to the rear/front protrusion of the surface (a transition in the reverse order is also possible). The energy barriers of both the transitions are extracted from the MEP; they are useful for the evaluation of the robustness of superhydrophobic surfaces (resistance to the Cassie-Baxter to Wenzel transition) and the droplet mobility on those surfaces (high mobility/small resistance to lateral displacements). The relation of the MEP with the potential transition paths coming from the solution space mapping is discussed.

Fog collecting biomimetic surfaces: Influence of microstructure and wettability

We analyzed the fog collection efficiency of three different sets of samples: replica (with and without microstructures), copper wire (smooth and microgrooved) and polyolefin mesh (hydrophilic, superhydrophilic and hydrophobic). The collection efficiency of the samples was compared in each set separately to investigate the influence of microstructures and/or the wettability of the surfaces on fog collection. Based on the controlled experimental conditions chosen here large differences in the efficiency were found. We found that microstructured plant replica samples collected 2-3 times higher amounts of water than that of unstructured (smooth) samples. Copper wire samples showed similar results. Moreover, microgrooved wires had a faster dripping of water droplets than that of smooth wires. The superhydrophilic mesh tested here was proved more efficient than any other mesh samples with different wettability. The amount of collected fog by superhydrophilic mesh was about 5 times higher than that of hydrophilic (untreated) mesh and was about 2 times higher than that of hydrophobic mesh.

Transition from Cassie to impaled state during drop impact on groove-textured solid surfaces

Liquid drops impacted on textured surfaces undergo a transition from the Cassie state characterized by the presence of air pockets inside the roughness valleys below the drop to an impaled state with at least one of the roughness valleys filled with drop liquid. This occurs when the drop impact velocity exceeds a particular value referred to as the critical impact velocity. The present study investigates such a transition process during water drop impact on surfaces textured with unidirectional parallel grooves referred to as groove-textured surfaces. The process of liquid impalement into a groove in the vicinity of drop impact through de-pinning of the three-phase contact line (TPCL) beneath the drop as well as the critical impact velocity were identified experimentally from high speed video recordings of water drop impact on six different groove-textured surfaces made from intrinsically hydrophilic (stainless steel) as well as intrinsically hydrophobic (PDMS and rough aluminum) materials. The surface energy of various 2-D configurations of liquid-vapor interface beneath the drop near the drop impact point was theoretically investigated to identify the locally stable configurations and establish a pathway for the liquid impalement process. A force balance analysis performed on the liquid-vapor interface configuration just prior to TPCL de-pinning provided an expression for the critical drop impact velocity, Uo,cr, beyond which the drop state transitions from the Cassie to an impaled state. The theoretical model predicts that Uo,cr increases with the increase in pillar side angle, α, and intrinsic hydrophobicity whereas it decreases with the increase in groove top width, w, of the groove-textured surface. The quantitative predictions of the theoretical model were found to show good agreement with the experimental measurements of Uo,cr plotted against the surface texture geometry factor in our model, {tan(α/2)/w}(0.5).

Biomimetic approach for liquid encapsulation with nanofibrillar cloaks

Technologies that are able to handle microvolumes of liquids, such as microfluidics and liquid marbles, are attractive for applications that include miniaturized biological and chemical reactors, sensors, microactuators, and drug delivery systems. Inspired from natural fibrous envelopes, here, we present an innovative approach for liquid encapsulation and manipulation using electrospun nanofibers. We demonstrated the realization of non-wetting soft solids consisting of a liquid core wrapped in a hydrophobic fibrillar cloak of a fluoroacrylic copolymer and cellulose acetate. By properly controlling the wetting and mechanical properties of the fibers, we created final architectures with tunable mechanical robustness that were stable on a wide range of substrates (from paper to glass) and floated on liquid surfaces. Remarkably, the realized fiber-coated drops endured vortex mixing in a continuous oil phase at high stirring speed without bursting or water losses, favoring mixing processes inside the entrapped liquid volume. Moreover, the produced cloak can be easily functionalized by incorporating functional particles, active molecules, or drugs inside the nanofibers.

Verification of icephobic/anti-icing properties of a superhydrophobic surface

Four aluminum surfaces with wettability varied from superhydrophilic to superhydrophobic were prepared by combining an etching and a coating process. The surface wettability was checked in terms of water contact angle (CA) and sliding angle (SA) under different humidity at -10 °C. High-speed photography was applied to study water droplet impact dynamics on these surfaces. It was found that single and successive water droplets could rebound on the superhydrophobic surface and roll off at a tilt angle larger than 30° under an extremely condensing weather condition (-10 °C and relative humidity of 85-90%). In addition, the superhydrophobic surface showed a strong icephobic property, the ice adhesion on this surface was only 13% of that on the superhydrophilic surface, though they had a similar nano/microtopological structure. Moreover, this superhydrophobic surface displayed an excellent durability of the icephobic property. The ice adhesion only increased to 20% and 16% of that on the superhydrophobic surface after the surface was undergone 20 icing/ice-breaking cycles and 40 icing/ice-melting cycles, respectively. Surface profile and XPS studies on these surfaces indicated a minor damage of the surface nano/microstructure and the coating layer upon these multiple ice-breaking and ice-melting processes. Therefore, this superhydrophobic surface could be a good candidate for icephobic applications.