Modeling Cassie droplets on superhydrophobic coatings with orthogonal fibrous structures

Development of Adjustable High- to Low-Adhesive Superhydrophobicity Using Aligned Electrospun Fibers

Superhydrophobic surfaces based on electrospun fibrous structures exhibit advantages of additive manufacturing and enable the passage of gases. Compared to randomly deposited fibers, directionally aligned fibers improve the control of surface wetting by a specified fiber orientation and predictable liquid-fiber contact interface. In this article, we create superhydrophobicity with adjustable adhesion based on the understanding of droplet wetting behavior on directionally aligned fibers. Directionally aligned polystyrene fibers with different diameters and interfiber distances (l) are produced using electrospinning with a rotating fin collector. The wetting behavior of droplets on the surfaces dressed by aligned fibers is characterized, and a thermodynamic model of wetting behavior is established to guide the experimental studies. As a result, high-adhesive superhydrophobicity is achieved on weak hydrophobic substrate surfaces dressed by aligned polystyrene fibers with a diameter of 1.8 μm and l between 5 and 130 μm. Water droplets (2 μL) exhibit a maximum contact angle of 156° and adhere to the fiber-dressed surfaces by tilting upside down. Low-adhesive superhydrophobicity is achieved by introducing an additional layer of aligned fibers to increase the transition energy barrier. On the dual-layer structure with an upper-layer l of 9 μm, droplets show a contact angle of 155° and can readily roll off the surface. Moreover, increasing the upper-layer l to 15 μm reserves the surface to high-adhesive superhydrophobicity.

Advances in the development of superhydrophobic and icephobic surfaces

Superhydrophobicity and icephobicity are governed by surface chemistry and surface structure. These two features signify a potential advance in surface engineering and have recently garnered significant attention from the research community. This review aims to simulate further research in the development of superhydrophobic and icephobic surfaces in order to achieve their wide-spread adoption in practical applications. The review begins by establishing the fundamentals of the wetting phenomenon and wettability parameters. This is followed by the recent advances in modeling and simulations of the response of superhydrophobic surfaces to static and dynamic droplets contact and impingement, respectively. In view of their versatility and multifunctionality, a special attention is given to the development of these surfaces using nanocomposites. Furthermore, the review considers advances in icephobicity, its comprehensive characterization and its relation to superhydrophobicity. The review also includes the importance of the use of superhydrophobic surface to combat viral and bacterial contamination that exist in fomites.

Contribution of Interfacial Bonding towards Geopolymers Properties in Geopolymers Reinforced Fibers: A Review

There is a burgeoning interest in the development of geopolymers as sustainable construction materials and incombustible inorganic polymers. However, geopolymers show quasi-brittle behavior. To overcome this weakness, hundreds of researchers have focused on the development, characterization, and implementation of geopolymer-reinforced fibers for a wide range of applications for light geopolymers concrete. This paper discusses the rapidly developing geopolymer-reinforced fibers, focusing on material and geometrical properties, numerical simulation, and the effect of fibers on the geopolymers. In the section on the effect of fibers on the geopolymers, a comparison between single and hybrid fibers will show the compressive strength and toughness of each type of fiber. It is proposed that interfacial bonding between matrix and fibers is important to obtain better results, and interfacial bonding between matrix and fiber depends on the type of material surface contact area, such as being hydrophobic or hydrophilic, as well as the softness or roughness of the surface.

Droplet Mobility on Hydrophobic Fibrous Coatings Comprising Orthogonal Fibers

Water droplet mobility on a hydrophobic surface cannot be guaranteed even when the droplet exhibits a high contact angle (CA) with the surface. In fact, droplet mobility on a surface, especially a fibrous surface, has remained an unsolved empirical problem. This paper is a combined experimental-computational study focused on droplet mobility on a fibrous surface. Electrospun polystyrene (PS) coatings were used in this work for their ability to exhibit high CAs simultaneously with low droplet mobility. To simplify this otherwise complicated problem and better isolate droplet-fiber interactions, the orientation of the fibers in the coatings was limited to the x and y directions. As the earth gravity was not strong enough to mobilize small droplets on PS coatings, experiments were conducted using ferrofluid droplets, and a magnet was used to make them move on the surface. Experimentally validated numerical simulations were used to enhance our understanding of the forces acting on a droplet before moving on the surface. Effects of Young-Laplace CA and fiber-fiber spacing on droplet mobility were investigated. In particular, it was found that droplet mobility depends strongly on the balance of forces exerted on the droplet by the fibers on the receding and advancing sides.