Tribological behaviors of polyimide composite films enhanced with fluorographene

Microhardness, Surface Roughness, and Wear Resistance Enhancement of Reinforced Conventional Glass Ionomer Cement Using Fluorinated Graphene Oxide Nanosheets

OBJECTIVES

 Conventional glass ionomer cements (GICs) have been considered the most prevalent restorative material however; the reduced mechanical qualities and decreased wear resistance have been the main challenges facing their wide clinical application. This study was designed to assess the mechanical properties of fluorinated graphene (FG) oxide-modified conventional GIC.

MATERIALS AND METHODS

 Composites of FG/GIC samples were prepared using (Medifil from PROMEDICA, Germany, shade A3) at different concentrations (0wt%) control group and (1wt%, 2wt% and 3wt% FG) groups using cylindrical molds (3mm × 6mm). FG was prepared using hydrothermal technique and characterized using XPERT-PRO Powder Diffractometer system for X-ray diffraction analysis and JEOL JEM-2100 high resolution transmission electron microscope. Vickers' hardness and wear resistance of GI samples were measured. Mechanical abrasion was performed via three-body tooth brushing wear test using ROBOTA chewing simulator coupled with a thermocycling protocol (Model ACH-09075DC-T, AD-Tech Technology Co., Ltd., Leinfelden-Echterdingen, Germany).

STATISTICAL ANALYSIS

 Comparisons between groups with respect to normally distributed numeric variables were performed using one-way analysis of variance test followed by posthoc test. While paired t-test was utilized for comparing data within the same group.

RESULTS

The surface roughness values of GICs (1wt% FG) and (2wt% FG) composites were significantly lower than those of the control and 3wt%FG groups. Vickers' hardness numbers were significantly higher in FG/GICs composites than in the control group (p≤0.05).

CONCLUSION

 GIC/FG combinations have sufficient strength to resist the occlusion stresses with improved hardness as compared with conventional GIC. GIC/FG appeared to be a promising restorative material.

Advanced progress on the significant influences of multi-dimensional nanofillers on the tribological performance of coatings

Over the past two decades, nanofillers have attracted significant interest due to their proven chemical, mechanical, and tribological performances. However, despite the significant progress realized in the application of nanofiller-reinforced coatings in various prominent fields, such as aerospace, automobiles and biomedicine, the fundamental effects of nanofillers on the tribological properties of coatings and their underlying mechanisms have rarely been explored by subdividing them into different sizes ranging from zero-dimensional (0D) to three-dimensional (3D) architectures. Herein, we present a systematic review of the latest advances on multi-dimensional nanofillers for enhancing the friction reduction and wear resistance of metal/ceramic/polymer matrix composite coatings. Finally, we conclude with an outlook for future investigations on multi-dimensional nanofillers in tribology, providing possible solutions for the key challenges in their commercial applications.

Impacts of polyimide enhanced by amino-modified fluorinated graphene: Thermal, mechanical and tribological behaviors

The fluorinated graphene (FG) is modified to get the amino-FG (AFG) which is applied as nanofiller of the polyimide (PI). The repulsion between the C-F bonds endows the AFG with well dispersion in polyimide (PI) matrix, and the amino groups of the AFG react with pyromellitic dianhydride to form strong physical and chemical interactions between the AFG and the PI chains. The results exhibit that the AFG obviously enhances the thermal stability, mechanical performances and wear resistant properties of the PI. When the AFG content reaches 0.5 wt%, the PI/AFG-0.5 composite shows the 35.5% higher tensile stress and 50% higher wear resistance than the PI, which are also higher than the PI/FG-0.5. The strong physical and chemical interactions between the AFG and the PI matrix enhance the interfacial compatibility of the PI/AFG composite, which is better to transfer the stress and heat, so as to enhance the mechanical and tribological properties of the PI. The worn surface changes of the PI/AFG composites indicate that the tribological mechanisms are the synergistic reaction of the abrasive wear and the fatigue wear.

Effect of Nanofillers on Tribological Properties of Polymer Nanocomposites: A Review on Recent Development

Polymer nanocomposites with enhanced performances are becoming a trend in the current research field, overcoming the limitations of bulk polymer and meeting the demands of market and society in tribological applications. Polytetrafluoroethylene, poly(ether ether ketone) and ultrahigh molecular weight polyethylene are the most popular polymers in recent research on tribology. Current work comprehensively reviews recent advancements of polymer nanocomposites in tribology. The influence of different types of nanofiller, such as carbon-based nanofiller, silicon-based nanofiller, metal oxide nanofiller and hybrid nanofiller, on the tribological performance of thermoplastic and thermoset nanocomposites is discussed. Since the tribological properties of polymer nanocomposites are not intrinsic but are dependent on sliding conditions, direct comparison between different types of nanofiller or the same nanofiller of different morphologies and structures is not feasible. Friction and wear rate are normalized to indicate relative improvement by different fillers. Emphasis is given to the effect of nanofiller content and surface modification of nanofillers on friction, wear resistance, wear mechanism and transfer film formation of its nanocomposites. Limitations from the previous works are addressed and future research on tribology of polymer nanocomposites is proposed.

Fluorinated Polyurethane-Based Enameled Wires with a Low Friction Coefficient

Fluorinated polyurethane (FPU) with a different fluorine content was prepared using perfluoropolyether glycols, poly(propylene glycol), and isophorone diisocyanate as starting materials, and 1,4-butanediol as a chain extender. The structure and molecular weight of FPU were characterized by Fourier transform infrared spectroscopy and gel permeation chromatography. A solution of FPU in xylene and cresol was then coated on copper wires using an enameled machine to prepare enameled wires. The friction coefficient and adhesion performance of the enameled wires were tested. The friction coefficient of the as-prepared enameled wires reached 0.095, which was much lower than 0.149 of the polyurethane without fluorine. FPU-based enameled wires also showed good mechanical performances and increased breakdown voltages. In addition, FPU exhibited good hydrophobic and oleophobic characterization.

Simultaneous determination of heavy metals by an electrochemical method based on a nanocomposite consisting of fluorinated graphene and gold nanocage

Fluorinated graphene/gold nanocage (FGP/AuNC) nanocomposite was developed for simultaneous determination of heavy metals using square wave anodic stripping voltammetry. Under optimized conditions, with a buffer pH of 5.0, a deposition potential of - 1.25 V, and a deposition time of 140 s, the method can obtain the best results. The FGP/AuNC electrode exhibits low limits of detection (0.08, 0.09, 0.05, 0.19, 0.01 μg L^-1), wide linear ranges (6-7000, 4-6000, 6-5000, 4-4000, 6-5000 μg L^-1), and well-separated stripping peaks (at - 1.10, - 0.77, - 0.50, - 0.01, 0.31 V vs Ag/AgCl) towards Zn²⁺, Cd²⁺, Pb²⁺, Cu²⁺, and Hg²⁺, respectively. Furthermore, the FGP/AuNC electrode is also used for simultaneous determination of Zn²⁺, Cd²⁺, Pb²⁺, Cu²⁺, and Hg²⁺ in real samples (peanut, rape bolt, and tea). Highly consistent results are found between the electrochemical method and atomic fluorescence spectrometry/inductively coupled plasma-mass spectrometry. The method has been successfully applied to the determination of heavy metal ions in agricultural food. Graphical abstract Schematic representation of simultaneous determination of heavy metal ions by electrochemical method. The FGP/AuNC (fluorinated graphene/gold nanocage) electrode is used to simultaneous determination of Zn²⁺, Cd²⁺, Pb²⁺, Cu²⁺, and Hg²⁺ by square wave anode stripping voltammetry.