Microencapsulation of pink pepper essential oil: Properties of spray-dried pectin/SPI double-layer versus SPI single-layer stabilized emulsions

Insights on tiger nut (Cyperus Esculentus L.) oil-loaded microcapsules: characterization and oxidation stability analysis

In this paper, tiger nut oil-loaded microcapsules (TNOMs) were prepared by complexation soybean protein isolate (SPI) and maltodextrin (MD) as wall materials using the spray drying method with tiger nut oil (TNO) as the core material, and its physicochemical properties and stabilities were characterized and analyzed. Under the optimum conditions, the encapsulation efficiency (EE) of TNOMs could reach up to 91.23%. Of note, after 60 days of storage at 60 °C, the peroxide value (PV) of TNO was almost 21.8 times as much as that of TNO encapsulated. Furthermore, TNOMs had good thermal stability below 200 °C and are sufficient for the general food processing needs. By fitting Arrhenius oxidation kinetics model, it was predicted that the shelf life of the product stored at 25 °C was 352.48 d. Therefore, it is promised to be applied to the development of high oleic acid food in the future. This study offered a theoretical framework for utilization and broadening the range of applications of TNO in the food industry.

Long-term storage of pink pepper essential oil microencapsulated by chickpea protein/pectin complexes: volatile release, antioxidant and antimicrobial activities

Pink pepper essential oil was microencapsulated with chickpea protein (CP) and chickpea protein/pectin (CP-HMP) by spray drying. The reconstitution and storage properties of the powders were evaluated after drying. The impact of microencapsulation in the volatiles release, antioxidant and antimicrobial activity of oil was evaluated during 135 days of storage. CP resulted in more soluble powders (93.52%), CP/HMP resulted in denser powders (0.39 g/mL) while wall material did not influence the wettability. Free pink pepper essential oil (FEO) showed a slight loss of the predominant terpenes (α-pinene, β-pinene, β-mircene, δ-3-carene and D-limonene) after encapsulation. In general, all samples showed an increase in the volatiles release during storage. The evaluation of mass loss showed that FEO had a high release of volatiles, followed by CP and CP-HMP. The antioxidant activity of the FEO decreased (10.8 μg Trolox/mg of oil) after 135 days of storage, whereas the antioxidant activity of CP (14.9) and CP-HMP (14) increased. Both microcapsules presented antimicrobial activity against Bacillus subtilis and Staphylococcus aureus during storage. CP microcapsules had a strong inhibitory effect against the strains tested, and this advantage was even more evident in long-term storage.

Long-acting sustained release microcapsules of oregano essential oil-loaded gelatin/carrageenan for food preservation against Botrytis cinerea

As a food-derived natural component, oregano essential oil (OEO) exhibits excellent activity against Botrytis cinerea (B. cinerea). However, its poor water solubility and chemical instability limit its application in preservation. In this study, we determined the composition of OEO and encapsulated it in microcapsules using gelatin/carrageenan (GE/CRG) as the capsule wall, achieving a particle size of 336.10 nm and an encapsulation efficiency of 87.79 %. The microcapsules realize the slow-release duration of OEO to over 80 h. More importantly, due to the slow-release effect of OEO, OEO-GE/CRG microcapsules demonstrated excellent inhibitory activity against B. cinerea with an EC50 value of 0.18 mg/mL. The microcapsule treatment significantly prolonged the preservation period of cherry tomatoes in infection models with B. cinerea. These results indicate that OEO-GE/CRG microcapsules could serve as a potential fungal inhibitor and agent for fruit storage and preservation.

Understanding emulsifier influence on complex coacervation: Essential oils encapsulation perspective

The objective of this research was to explore the viability of pea protein as a substitute for gelatin in the complex coacervation process, with a specific focus on understanding the impact of incorporating an emulsifier into this process. The study involved the preparation of samples with varying polymer mixing ratios (1:1, 1:2, and 2:1) and emulsifier content. As core substances, black pepper and juniper essential oils were utilized, dissolved beforehand in grape seed oil or soybean oil, to minimize the loss of volatile compounds. In total, 24 distinct samples were created, subjected to freeze-drying to produce powder, and then assessed for their physicochemical properties. Results revealed the significant impact of emulsifier addition on microcapsule parameters. Powders lacking emulsifiers exhibited higher water solubility (57.10%-81.41%) compared to those with emulsifiers (24.64%-40.13%). Moreover, the emulsifier significantly decreased thermal stability (e.g., without emulsifier, Ton = 137.21°C; with emulsifier, Ton = 41.55°C) and adversely impacted encapsulation efficiency (highest efficiency achieved: 67%; with emulsifier: 21%).

Selenized lactic acid bacteria microencapsulated by spray drying: A promising strategy for beef cattle feed supplementation

This study aimed to assess the technical feasibility of incorporating selenized Lactobacillus spp. microencapsulated via spray drying into cattle feed. Gum Arabic and maltodextrin were used as encapsulating agents. The encapsulation process was carried out with a drying air flow rate of 1.75 m3/min, inlet air temperature of 90°C, and outlet air temperature of 75°C. The viability of the encapsulated microorganisms and the technological characteristics of the obtained microparticles were evaluated. Microorganisms were incorporated into beef cattle feed to supplement their diet with up to 0.3 mg of Se per kilogram of feed. The encapsulated particles, consisting of a 50/50 ratio of gum Arabic/maltodextrin at a 1:20 proportion of selenized biomass to encapsulant mixture, exhibited superior technical viability for application in beef cattle feed. Supplemented feeds displayed suitable moisture, water activity, and hygroscopicity values, ensuring the preservation of viable microorganisms for up to 5 months of storage, with an approximate count of 4.5 log CFU/g. Therefore, supplementing beef cattle feed with selenized and microencapsulated lactic acid bacteria represents a viable technological alternative, contributing to increased animal protein productivity through proper nutrition.

Stability of Buriti Oil Microencapsulated in Mixtures of Azuki and Lima Bean Flours with Maltodextrin

Buriti oil (Mauritia flexuosa L.) is rich in carotenoids, mainly β-carotene, and has great value for application as a food, pharmaceutical, or cosmetic ingredient, as well as a natural pigment. Microencapsulation is a promising technique to protect compounds sensitive to degradation such as β-carotene. Materials composed of carbohydrates and proteins, such as azuki bean (Vigna angularis L.) and lima bean (Phaseolus lunatus L.) flours, are alternative matrices for microencapsulation, which additionally provide good amounts of nutrients. In combination with maltodextrin, the flours represent a protective barrier in stabilizing lipophilic compounds such as buriti oil for subsequent spray drying. In this work, the performance of mixtures of maltodextrin with whole azuki and lima bean flours was evaluated in the microencapsulation of buriti oil. The microcapsules showed good results for solubility (>80%), hygroscopicity (~7%), encapsulation efficiency (43.52 to 51.94%), and carotenoid retention (64.13 to 77.49%.) After 77 days of storage, the microcapsules produced maintained 87.79% and 90.16% of carotenoids, indicating that the powders have high potential for application as encapsulants in the food and pharmaceutical industries.

New perspective on protein-based microcapsules as delivery vehicles for sensitive substances: A review

Sensitive substances have attracted wide attention due to their rich functional activities, such as antibiosis activities, antioxidant activities and prevent disease, etc. However, the low stability of sensitive substances limits their bioavailability and functional activities. Protein-based microcapsules can encapsulate sensitive substances to improve their adverse properties due to their good stability, strong emulsifying ability and wide source. Therefore, it is necessary to fully elaborate and summarize protein-based microcapsules to maximize their potential benefits in nutritional interventions. The focus of this review is to highlight the classification of protein-based microcapsules. In addition, the principles, advantages and disadvantages of preparation methods for protein-based microcapsules are summarized. Some novel preparation methods for protein-based microcapsules are also emphasized. Moreover, the mechanism of protein-based microcapsules that release sensitive substances in vitro is elucidated and summarized. Furthermore, the applications of protein-based microcapsules are outlined. Protein-based microcapsules can effectively encapsulate sensitive substances, which improve their bioavailability, and provide protective effects during storage and gastrointestinal digestion. In addition, microcapsules can improve the sensory quality of food and enhance its stability. The performance of protein-based microcapsules for delivering sensitive substances is influenced by factors such as protein type, the ratio between protein ratio and the other wall material, the preparation process, etc. Future research should focus on the new composite protein-based microcapsule delivery system, which can be applied to in vivo research and have synergistic effects and precise nutritional functions. In summary, protein-based microcapsules have broader research prospects in the functional foods and nutrition field.

Utilization of gallic acid-crosslinked soy proteins as wall material for chia oil microencapsulation

BACKGROUND

Chia oil represents the vegetable source with the highest content of omega-3 fatty acids. However, the incorporation of polyunsaturated fatty acids into food is limited due to their susceptibility toward oxidation. This investigation aimed to study the microencapsulation of chia oil (CO), using gallic acid (GA) crosslinked-soy protein isolate (SPI) as a wall material and its effect on its oxidative stability.

RESULTS

Microcapsules presented a moisture content, water activity, and encapsulation efficiency of around 2.95-4.51% (wet basis); 0.17 and 59.76-71.65%, respectively. Rancimat tests showed that with higher GA content, the induction period increased up to 27.9 h. The storage test demonstrated that the microencapsulated oil with crosslinked wall material has lower values of hydroperoxides and higher induction times concerning the non-crosslinked oil. Finally, the fatty acid profile at this storage time indicated that microcapsules with GA did not have significant changes. In vitro digestion exhibited a reduction in the percentage of bioavailable oil for crosslinked microcapsules, but with no variations in its chemical quality, and an increase in the total polyphenols amount and antioxidant activity.

CONCLUSION

The results obtained demonstrated that the microencapsulation of CO using SPI crosslinked with GA as wall material exerted a very important protective effect since a synergistic effect could be described between the microencapsulation effect and the antioxidant power of GA. © 2023 Society of Chemical Industry.

Microencapsulation of Chilean Papaya Waste Extract and Its Impact on Physicochemical and Bioactive Properties

The microencapsulation of bioactive extracts of Chilean papaya waste, including both seeds and skin, was investigated. Papaya waste extract microcapsules utilizing maltodextrin at 10% (MD10), 20% (MD20), and 30% (MD30) (w/v) as the wall material through the freeze-drying process were obtained, and subsequently their physicochemical, antioxidant, and antimicrobial properties were evaluated. The TPC efficiency and yield values achieved were more than 60% for the microencapsulated seed and skin extracts, respectively. The best results for phenolic and antioxidant compounds were found in the microencapsulated seed extract with MD20, with a value of 44.20 ± 3.32 EAG/g DW for total phenols and an antioxidant capacity of 12.0 ± 0.32 mol ET/g DW for the DPPH and 236.3 ± 4.1 mol ET/g DW for the FRAP assay. In addition, the seed and skin samples reduced ROS generation in H2O2-treated Hek293 cells. In terms of antimicrobial activity, values ranging from 7 to 15 mm of inhibitory halos were found, with the maximum value corresponding to the inhibition of S. aureus, for both microencapsulated extracts. Therefore, the successful microencapsulation of the waste bioactive extracts (seed and skin) with the demonstrated antimicrobial and antioxidant properties highlight the bioactivity from Chilean papaya waste resources.

Chia Oil Microencapsulation Using Tannic Acid and Soy Protein Isolate as Wall Materials

The use of proteins to produce oil-containing microcapsules has been previously analyzed; however, their chemical modification, in order to improve their performance as wall materials, is a strategy that has not been widely developed yet. This study aimed to analyze the chemical modification of the proteins through cross-linking reactions with tannic acid and to evaluate their performance as wall materials to the microencapsulation of oils rich in polyunsaturated fatty acids. The cross-linking reaction of isolated soy protein and tannic acid was carried out at pH 10-11 and 60 °C. Subsequently, emulsions were made with a high-speed homogenizer and microcapsules were obtained by spray drying. Microcapsules were characterized by particle size, morphology (SEM), total pore area and % porosity (mercury intrusion methodology), superficial properties (contact angle), and size distribution of oil droplets (by laser diffraction). Additionally, encapsulation efficiency was determined as a function of total and surface oil. Oil chemical stability and quality were studied by Rancimat, hydroperoxide values, and fatty acid profiles. In addition, a storage test was performed for 180 days, and released oil and polyphenols were determined by in vitro gastric digestion. Moreover, the fatty acid composition of the oil and the total polyphenol content and antioxidant capacity of polyphenols were analyzed. The results showed that spray-dried microcapsules had an encapsulation efficiency between 54 and 78%. The oxidative stability exhibited a positive correlation between the amount of polyphenols used and the induction time, with a maximum of 27 h. The storage assay showed that the peroxide value was lower for those cross-linked microcapsules concerning control after 180 days. After the storage time, the omega-3 content was reduced by 49% for soy protein samples, while cross-linked microcapsules maintained the initial concentration. The in-vitro digestion assay showed a decrease in the amount of oil released from the cross-linked microcapsules and an increase in the amount of polyphenols and a higher antioxidant capacity for all samples (for example, 238.10 mgGAE/g and 554.22 mg TE/g for undigested microcapsules with TA 40% versus 322.09 mgGAE/g and 663.61 mg TE/g for digested samples). The microcapsules showed a high degree of protection of the encapsulated oil, providing a high content of polyunsaturated fatty acids (PUFAS) and polyphenols even in prolonged storage times.

Encapsulation of Bioactive Peptides by Spray-Drying and Electrospraying

Bioactive peptides derived from enzymatic hydrolysis are gaining attention for the production of supplements, pharmaceutical compounds, and functional foods. However, their inclusion in oral delivery systems is constrained by their high susceptibility to degradation during human gastrointestinal digestion. Encapsulating techniques can be used to stabilize functional ingredients, helping to maintain their activity after processing, storage, and digestion, thus improving their bioaccessibility. Monoaxial spray-drying and electrospraying are common and economical techniques used for the encapsulation of nutrients and bioactive compounds in both the pharmaceutical and food industries. Although less studied, the coaxial configuration of both techniques could potentially improve the stabilization of protein-based bioactives via the formation of shell-core structures. This article reviews the application of these techniques, both monoaxial and coaxial configurations, for the encapsulation of bioactive peptides and protein hydrolysates, focusing on the factors affecting the properties of the encapsulates, such as the formulation of the feed solution, selection of carrier and solvent, as well as the processing conditions used. Furthermore, this review covers the release, retention of bioactivity, and stability of peptide-loaded encapsulates after processing and digestion.

Artificial Neural Networks to Optimize Oil-in-Water Emulsion Stability with Orange By-Products

The use of artificial neural networks (ANNs) is proposed to optimize the formulation of stable oil-in-water emulsions (oil 6% w/w) with a flour made from orange by-products (OBF), rich in pectins (21 g/100 g fresh matter), in different concentrations (0.95, 2.38, and 3.40% w/w), combined with or without soy proteins (0.3 and 0.6% w/w). Emulsions containing OBF were stable against coalescence and flocculation (with 2.4 and 3.4% OBF) and creaming (3.4% OBF) for 24 h; the droplets' diameter decreased up to 44% and the viscosity increased up to 37% with higher concentrations of OBF. With the protein addition, the droplets' diameter decreased by up to 70%, and flocculation increased. Compared with emulsions produced with purified citrus pectins (0.2 and 0.5% w/w), OBF emulsions exhibited up to 32% lower viscosities, 129% larger droplets, and 45% smaller Z potential values. Optimization solved with ANNs minimizing the droplet size and the emulsion instability resulted in OBF and protein concentrations of 3.16 and 0.14%, respectively. The experimental characteristics of the optimum emulsion closely matched those predicted by ANNs demonstrating the usefulness of the proposed method.

Progress in the Application of Food-Grade Emulsions

The detailed investigation of food-grade emulsions, which possess considerable structural and functional advantages, remains ongoing to enhance our understanding of these dispersion systems and to expand their application scope. This work reviews the applications of food-grade emulsions on the dispersed phase, interface structure, and macroscopic scales; further, it discusses the corresponding factors of influence, the selection and design of food dispersion systems, and the expansion of their application scope. Specifically, applications on the dispersed-phase scale mainly include delivery by soft matter carriers and auxiliary extraction/separation, while applications on the scale of the interface structure involve biphasic systems for enzymatic catalysis and systems that can influence substance digestion/absorption, washing, and disinfection. Future research on these scales should therefore focus on surface-active substances, real interface structure compositions, and the design of interface layers with antioxidant properties. By contrast, applications on the macroscopic scale mainly include the design of soft materials for structured food, in addition to various material applications and other emerging uses. In this case, future research should focus on the interactions between emulsion systems and food ingredients, the effects of food process engineering, safety, nutrition, and metabolism. Considering the ongoing research in this field, we believe that this review will be useful for researchers aiming to explore the applications of food-grade emulsions.

Improved protective and controlled releasing effect of fish oil microcapsules with rice bran protein fibrils and xanthan gum as wall materials

This study aimed to prepare fish oil microcapsules by freeze-drying an emulsion co-stabilized by rice bran protein fibrils (RBPFs) and xanthan gum (XG) to improve the oxidation stability and controlled release effect. Emulsions stabilized either solely by RBPFs or unfibrillated rice bran protein (RBP) or by a combination of RBP and XG were also fabricated as microcapsule templates for comparison. The rheological properties, particle size, and zeta potential of the emulsions were examined. In addition, the characteristics of the fish oil microcapsules such as surface oil content, encapsulation efficiency, water activity, moisture content, morphological structure, oxidation stability, and digestive performance were also assessed. The rheological properties revealed that the addition of XG increased the storage modulus of the emulsion and reduced the loss modulus and apparent viscosity. At shear rates of 0-100 s^-1, the fish oil emulsion did not exhibit any gel properties or shear thinning. Fibrillation increased the particle size of the fish oil emulsion, whereas adding XG reduced the droplet size. The combination of RBP fibrillation and XG addition provided the highest encapsulation efficiency for fish oil. Fibrillation reduced the water activity and moisture content of the fish oil microcapsules. The anisotropy of the fibrils and the high viscosity of XG produced a layer of wrapping on the continuous heterogeneous surface of the freeze-dried powder particles. RBPF/XG microcapsules stored at 45 °C for 1 month had the lowest peroxide value and thiobarbituric acid value, the lowest surface oil content, and the lightest yellowness. These results suggest that the combination of RBPFs and XG provides better encapsulation and protective effects for fish oil microcapsules. Upon simulated digestion, the microcapsules containing XG and RBPFs exhibited a more favorable controlled release of free fatty acids. These findings indicate that microcapsules formed from emulsions co-stabilized by XG and RBPFs are suitable for encapsulating fish oil in functional foods.

Functional Properties of Physically Pretreated Kidney Bean and Mung Bean Flours and Their Performance in Microencapsulation of a Carotenoid-Rich Oil

Microencapsulation can improve protection for compounds that degrade easily, such as β-carotene that is present in large amounts in buriti oil (Mauritia flexuosa). Encapsulating matrices are mainly composed of proteins and polysaccharides, which are often combined to improve their performance as a protective barrier. Beans, such as dark red kidney beans (Phaseolus vulgaris) and mung beans (Vigna radiata), are excellent protein sources that contain significant amounts of the essential amino acids. Bean flours are low in fat and naturally provide a blend of high-quality protein and carbohydrates that may stabilize lipophilic compounds for subsequent spray-drying. Whole bean flours, rather than refined individual biopolymers, may represent more sustainable alternative wall materials for microencapsulate bioactive compounds. This work aimed to evaluate the use of flours produced from red kidney beans and mung beans, which have been submitted to different physical pretreatments, as wall materials for microencapsulation of buriti oil by spray-drying. Different bean treatments were evaluated: untreated (control), soaked in water for 24 h, and soaked in water for 24 h followed by boiling for 30 min. The flours' proximate composition was not affected by the treatments (p < 0.05), showing similar values of carbohydrate (63.8–67.9%), protein (19.2–24.6%), and lipid (1.2–1.9%) contents. Both bean species had the water absorption capacity (WAC) increased by boiling, while the oil absorption capacity (OAC) was not altered by the treatments. Flours produced with raw or soaked beans showed emulsion activity (EA) and emulsion stability (ES) greater than 70%. Raw bean flours also showed better foaming properties, which may be indicative of higher levels of antinutritional factors. The soaked bean flours showed the best results for both type of beans, especially with regard to emulsifying properties, and were selected as wall materials for buriti oil microencapsulation. Different ratios of flour and maltodextrin were used to produce oil-in-water emulsions that were then spray-dried. Buriti oil microcapsules showed good physicochemical properties, with moisture around 3%, aw <0.3, and hygroscopicity around 5%. The carotenoid encapsulation efficiency ranged from 68.2 to 77.9%. Bean flours showed to function as a sustainable and nutrient-rich alternative wall material for microencapsulation.

Nanoencapsulation of Mandarin Essential Oil: Fabrication, Characterization, and Storage Stability

This study evaluates the combined efficiency of whey protein isolate (WPI) with maltodextrin (MD) and gum arabic (GA), as a delivery system for encapsulating Citrus reticulata essential oil (CEO). The wall materials blended at different rates were produced to obtain seven formulations of nanocapsules (NCEO), namely NCEO-GA, NCEO-MD, NCEO-WPI, NCEO-GA/MD, NCEO-GA/WPI, NCEO-MD/WPI, and NCEO-GA/MD/WPI. The interaction between CEO and WPI was simulated by molecular docking. Findings showed that the physicochemical characteristics and storage stability of formulations containing WPI were considerably improved. The NCEO-GA/MD/WPI formulation demonstrated the optimum values of encapsulation efficiency (92.08%), highest glass transition temperature (79.11 °C), high crystallinity (45.58%), high thermal stability (mass loss at 100 °C < 5%), and also had the highest antioxidant activity and lowest peroxide value after storage. This study demonstrated that combining WPI with MD and GA, as wall material encapsulation, can produce nanocapsules with superior properties to those created using polysaccharides individually.

Performance of oil-in-water emulsions stabilized by different types of surface-active components

The emulsion stability depends on the physicochemical properties of the dispersed phase and their interaction with the continuous phase. Surface-active compounds (SAC) are added in emulsions to reduce the interfacial tension (IT) between these phases and keep the oil droplets stabilized. Moreover, small amounts of SAC can occupy intermolecular voids in the dried matrix, reducing the oxidation. However, the formulation must reflect a trade-off between protection and emulsion stabilization. Therefore, this work aimed to identify the minimum concentration of SAC (modified starch-MS, gelatin-GE, and whey protein isolate-WPI) ranging from 0.48 to 6 % (w/w) to form and stabilize droplets of an unsaturated triglyceride (fish oil-FO) or a volatile oil (orange essential oil-OEO). GE did not change the IT (6.7 mN/m) and stabilized the emulsions only through an increase of the viscosity (∼42 mPas for FO-emulsions and ∼97 mPas for OEO-emulsions), presenting high droplet size (∼10 μm) and low surface charge (∼1.5 mV). WPI reduced the IT to a limit value (4.5 mN/m at 1.2 % w/w for OEO and 5.3 mN/m at 2.4 % w/w for FO), whereas MS reduce constantly the IT with the increase of the concentration for both oils (∼4.2 mN/m at 6 % w/w). Both WPI and MS-emulsions presented similar droplet size (∼2.0 μm), but WPI presented higher surface charge of WPI-emulsions (-45 mV) than MS-emulsions (-30 mV). This study allowed to gain a consistent understanding of structure-property relationships on the use of SAC in emulsions.