A novel material poly(N-acryloyl-L-serine)-brush grafted kaolin for efficient elimination of malachite green dye from aqueous environments

Electrolytic synthesis of γ-Al2O3 nanoparticle from aluminum scrap for enhanced methylene blue adsorption: experimental and RSM modeling

The presence of methylene blue (MB) dye in wastewater has raised concern about human health and environmental ecology due to potential carcinogenic, and mutagenic effects. Therefore, this work aims to remove MB dye from wastewater using γ-Al2O3 nanoparticles synthesized from aluminum scrap via simple electrolytic method. The successful synthesis of the adsorbent was confirmed by a range of spectroscopy and microscopy techniques, including XRD, SEM, FTIR, and BET. The central composite design (CCD) of the response surface methodology (RSM) method was used to optimize the processing parameters such as solution pH, contact time, initial MB concentration, and adsorbent dose. The ANOVA results clearly shows that the quadratic model (p < 0.0001) was sufficient to the best predicting of the removal performance of MB dye (R2 = 0.9862). The optimum condition for the maximum MB dye removal (98.91%) was achieved at solution pH of 8.298, initial MB concentration of 31.657 mg/L, adsorbent dose of 0.387 g/L, and contact time of 46.728 min. Nano-γ-Al2O3 was shown to have a good surface area of 59 mg2/g by BET analysis. The adsorption kinetics follows the pseudo-second-order model (R2 = 0.997). With a maximum adsorption capacity of 137.17 mg/g, the Langmuir isotherm model (R2 = 984) provides the best fit to the adsorption isotherm data, indicating a monolayer adsorption process. Furthermore, thermodynamic analysis demonstrated that the adsorption of MB dye was an endothermic and spontaneous process. The reusability study showed that γ-Al2O3 nano-adsorbent retained 85.08% of its original removal efficiency after five cycles. According to the findings of the study, MB dye molecules were taken up by γ-Al2O3 nano-adsorbent via hydrogen bond formation, Van der Waals interaction, and electrostatic attraction. Therefore, γ-Al2O3 nanoparticles can be used as a potentially eco-friendly and low-cost adsorbent for the removal of MB dye from aqueous solutions.

Ultra-fast and ultra-efficient phenol removal from aqueous solution using a nano biocarbon adsorbent by RSM-CCD method: parameters, isotherm, kinetic, ANOVA

The purpose of this research is to investigate the ability of peanut shell activated carbon (PSAC) to adsorb phenol from aqueous solutions. Phenolic wastewater in various industries and their release to the environment are environmental problems. Among the various separation methods, adsorption is an accepted method because of its efficiency, simplicity, cost-effectiveness, and possibility to use different adsorbent materials to achieve maximum adsorption efficiency. Response surface methodology (RSM) was used to minimize the required experiments, modeling, finding the optimal point, and variance analysis. Among the studied variables, pH, adsorbent dosage, and initial concentration are important. The results show that it is possible to completely remove at 300 ppm of phenol concentration and 5 min. Characterization of PSAC was done using Fourier transform infrared spectroscopy spectrum (FTIR), X-ray diffraction (XRD), transmission electron microscopy (TEM), Brunauer-Emmet-Teller (BET), and size analysis. By examining the isotherm models, it was found that the adsorption follows the Langmuir model. The maximum adsorption capacity was 250 mg g-1 based on the Langmuir model. The three combined features of complete removal, ultra-fast adsorption, and high adsorption capacity are the unique features of this nano biocarbon for phenol removal.

A novel porous lignocellulosic standing hierarchical hydroxyapatite for enhanced aqueous copper(II) removal

Potentially toxic metal-polluted water resources are a heavily discussed topic the pollution by potentially toxic metals can cause significant health risks. Nanomaterials are actively developed towards providing high specific surface area and creating active adsorption sites for the treatment and remediation of these polluted waters. In an effort to tackle the limitations of conventional type adsorbents, nano-hydroxyapatite (HAp) was developed in this study by in situ generation onto wood powder, resulting in the formation of uniform hybrid powder (HAp@wood composite) structure consisting of HAp nanoparticles that showed the removal efficiency up to 80 % after 10 min; the maximum adsorption capacity for Cu(II) ions (98.95 mg/g-HAp) was higher compared to agglomerated nano-HAp (72.85 mg/g-HAp). The adsorption capacity of Cu(II) remained stable (89.85-107.66 mg/g-HAp) during the four adsorption-desorption cycles in multi-component system, thereby demonstrating high selectivity for Cu(II). This approach of using nanoparticle is relatively simple yet effective in improving the adsorption of potentially toxic metals and the developed approach can be used to develop advanced nanocomposites in commercial wastewater treatment.

Adsorptive removal of dichlorophenoxyacetic acid (2,4-D) using novel nanoparticles based on cationic surfactant-coated titania nanoparticles

A novel nanomaterial based on cationic surfactant-coated TiO₂ nanoparticle (CCTN) was systematically fabricated in this work. Synthesized titania nanoparticles were thoroughly characterized by XRD, FT-IR, HR-TEM, TEM-EDX, SEM with EDX mapping, BET, and ζ potential measurements. The adsorption of cationic surfactant, cetyltrimethylammonium bromide (CTAB), on TiO₂ was studied under various pH and ionic strength conditions. Adsorption of CTAB on TiO₂ increased with ionic strength increment in the presence of hemimicelle monolayer structure, indicating that nonelectrostatic and electrostatic forces control CTAB uptake. CTAB adsorption isotherms on TiO₂ were according to a two-step model. Potential application in pesticide removal of 2,4-dichorophenoxy acetic acid (2,4-D) using CCTN was also studied. Optimum parameters for 2,4-D treatment through adsorption technique were pH 5, adsorption time of 120 min, and CCTN dosage of 10 mg·mL^-1. Very low 2,4-D removal efficiency using TiO₂ without CTAB coating was found to be approximately 28.5% whereas the removal efficiency was up to about 90% by using CCTN under optimum conditions, and the maximum adsorption capacity of 12.79 mg·g^-1 was found. Adsorption isotherms of 2,4-D on CCTN were more suitable with the Langmuir model than Freundlich. Adsorption mechanisms of 2,4-D on CCTN were mainly governed by Columbic attraction based on isotherms and surface charge changes.

Adsorption of Cationic Contaminants by Cyclodextrin Nanosponges Cross-Linked with 1,2,3,4-Butanetetracarboxylic Acid and Poly(vinyl alcohol)

Cationic organic pollutants (dyes and pesticides) are mainly hydrosoluble and easily contaminate water and create a serious problem for biotic and abiotic species. The elimination of these dangerous contaminants from water was accomplished by adsorption using cyclodextrin nanosponges. These nanosponges were elaborated by the cross-linking between 1,2,3,4-butanetetracarboxylic acid and β-cyclodextrin in the presence of poly(vinyl alcohol). Their physicochemical characteristics were characterized by gravimetry, acid-base titration, TGA, 13C NMR, ATR-FTIR, Raman, X-ray diffraction, and Stereomicroscopy. The BP5 nanosponges displayed 68.4% yield, 3.31 mmol/g COOH groups, 0.16 mmol/g β-CD content, 54.2% swelling, 97.0% PQ removal, 96.7% SO removal, and 98.3% MG removal for 25 mg/L of initial concentration. The pseudo-second-order model was suitable for kinetics using 180 min of contact time. Langmuir isotherm was suitable for isotherm with the maximum adsorption of 120.5, 92.6, and 64.9 mg/g for paraquat (PQ), safranin (SO), and malachite green (MG) adsorption, respectively. Finally, the reusability performance after five regeneration times reached 94.1%, 91.6%, and 94.6% for PQ, SO, and MG adsorption, respectively.

Insights into the adsorption mechanism of tannic acid by a green synthesized nano-hydroxyapatite and its effect on aqueous Cu(II) removal

The polyphenolic tannic acid (TA) has been widely used in the stabilization and surface modification of nanomaterials. The interaction mechanism of TA with the biogenic nano-hydroxyapatite (nHAP) and its environmental importance, however, are poorly understood. This study explored the adsorption of TA using the green synthesized, eggshell-derived nHAP and implications of this process for the removal of aqueous Cu(II) via batch adsorption experiments, Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) investigations. TA adsorption by nHAP was a complex pH-dependent process and significantly correlated with TA molecule speciation and amphoteric properties of nHAP via multiple adsorption modes including surface complexation, electrostatic attraction, and hydrogen bond. The maximum TA adsorption amount was found to be 94.8 mg/g for less crystalline nHAP with lower calcination temperature. In the ternary Cu-TA-nHAP systems, TA promoted Cu(II) adsorption at pH < 5 and reduced Cu(II) uptake at pH > 5. Further studies of the effects of ionic strength and addition sequences, as well as Raman, FTIR, and XPS analyses revealed Cu(II) adsorption on nHAP was mainly dominated by inner-sphere surface complexation. These results can shed light on not only the utility of biogenic nHAP for TA and Cu(II) adsorption but also the evaluation of the effect of TA on the environmental behavior of heavy metals.

Enhanced Cr(VI) removal from water using a green synthesized nanocrystalline chlorapatite: Physicochemical interpretations and fixed-bed column mathematical model study

Apatite-based minerals have attracted much attention in the remediation of heavy metal-contaminated environment. However, exploring apatite with efficient adsorption performance for inorganic oxyanions such as Cr(VI) remains a challenge. Herein, a novel nanocrystalline chlorapatite (ClAP) was promptly prepared by a green method using eggshell wastes as calcium source with the purpose to enhance Cr(VI) adsorption capability. The generated ClAP was characterized by XRD, SEM-EPMA, TEM, FTIR, and BET analyses. Batch and column experiments were subsequently carried out to explore the influencing factors, adsorption capacity and removal mechanism. Results showed that ClAP exhibited excellent stability and adsorption performance for Cr(VI) (63.47 mg g^-1), which was much greater than that of hydroxyapatite and most reported materials. The adsorption process was fitted well by the pseudo-second-order model and the Langmuir model. In fixed bed column experiments, a novel time-fractional derivative model exhibited much better suitability in interpreting the observed breakthrough curves of Cr(VI) than traditional models. Furthermore, the reusability of ClAP in column was evaluated. Results showed that the adsorption capacity maintained well after consecutively reused for five cycles. Studies of the effect of pH, as well as FTIR and XPS investigations indicated that Cr(VI) adsorption was mainly ascribed to electrostatic interactions and surface complexation, while the reduction of Cr(VI) to the low-toxicity Cr(III) also existed in the adsorption process. The ClAP adsorbent was also successfully used for Cr(VI) remediation from real wastewater. Hence, nanocrystalline ClAP can be a promising material for enhancing the elimination of oxyanion contaminants such as Cr(VI) from water.