MoS2/Ni(OH)2 composites derived from in situ grown Ni-MOF coating MoS2 as electrode materials for supercapacitor and electrochemical sensor

Microwave Construction of NiSb/NiTe Composites on Ni-Foam for High-Performance Supercapacitors

In this paper, NiSb/NiTe/Ni composites were smoothly developed via the microwave method for supercapacitors. The synthesis of NiSb/NiTe crystals was revealed by X-ray photoelectron spectroscopy and X-ray diffraction. The analytic results of scanning electron microscopy and energy dispersive spectroscopy uncover the microscopic morphology as well as the constituent elements of the composites. Self-supported NiSb/NiTe is a supercapacitor cathode that combines high capacitance with excellent cycling stability. The obtained composite electrode displayed remarkable electrochemical properties, presenting a special capacitance of 1870 F g-1 (1 A g-1) and 81.5% of the original capacity through 30,000 times (10 A g-1) of the charging/discharging process. Further, an asymmetric supercapacitor was prepared employing NiSb/NiTe as a cathode and activated carbon as an anode. NiSb/NiTe//AC exhibited a high energy density of 224.6 uW h cm-2 with a power density of 750 μW cm-2 and provided a favorable cycling stability of 83% after 10,000 cycles.

Fabrication of an Azithromycin Sensor

Azithromycin (AZY) is a well-known top-prioritized antibiotic and is used by humans in strong concentrations. However, the side effects of the AZY antibiotic may cause some serious and significant damage to humans and the environment. Thus, there is a need to develop effective and sensitive sensors to monitor accurate concentrations of AZY. In the last decade, electrochemistry-based sensors have received enormous attention from the scientific community because of their high sensitivity, selectivity, cost-effectiveness, fast response, rapid detection response, simple fabrication, and working principle. It is important to mention that electrochemical sensors rely on the properties of electrode modifiers. Hence, the selection of electrode materials is of great significance when designing and developing efficient and robust electrochemical sensors. In this study, we fabricated an AZY sensor by utilizing a molybdenum disulfide/titanium aluminum carbide (MoS2@Ti3AlC2) composite as the electrode material. The MoS2@Ti3AlC2 composite was synthesized via a simple sonication process. The synthesized MoS2@Ti3AlC2 composite was characterized using a powder X-ray diffraction (XRD) method to examine the phase purity and formation of the MoS2@Ti3AlC2 composite. Scanning electron microscopy (SEM) was used to study the surface morphological features of the prepared MoS2@Ti3AlC2 composite, whereas energy dispersive X-ray spectroscopy (EDAX) was adopted to determine the elemental composition of the prepared MoS2@Ti3AlC2 composite. The glassy carbon (GC) electrode was modified with the prepared MoS2@Ti3AlC2 composite and applied as the AZY sensor. The sensing performance of the MoS2@Ti3AlC2 composite-modified GC electrode was studied using linear sweep voltammetry. The sensor demonstrated excellent performance when determining AZY and showed a good detection limit of 0.009 µM with a sensitivity of 6.77 µA/µM.cm2.

Recent advances in surface-mounted metal-organic framework thin film coatings for biomaterials and medical applications: a review

Coatings of metal-organic frameworks (MOFs) have potential applications in surface modification for medical implants, tissue engineering, and drug delivery systems. Therefore, developing an applicable method for surface-mounted MOF engineering to fabricate protective coating for implant tissue engineering is a crucial issue. Besides, the coating process was desgined for drug infusion and effect opposing chemical and mechanical resistance. In the present review, we discuss the techniques of MOF coatings for medical application in both in vitro and in vivo in various systems such as in situ growth of MOFs, dip coating of MOFs, spin coating of MOFs, Layer-by-layer methods, spray coating of MOFs, gas phase deposition of MOFs, electrochemical deposition of MOFs. The current study investigates the modification in the implant surface to change the properties of the alloy surface by MOF to improve properties such as reduction of the biofilm adhesion, prevention of infection, improvement of drugs and ions rate release, and corrosion resistance. MOF coatings on the surface of alloys can be considered as an opportunity or a restriction. The presence of MOF coatings in the outer layer of alloys would significantly demonstrate the biological, chemical and mechanical effects. Additionally, the impact of MOF properties and specific interactions with the surface of alloys on the anti-microbial resistance, anti-corrosion, and self-healing of MOF coatings are reported. Thus, the importance of multifunctional methods to improve the adhesion of alloy surfaces, microbial and corrosion resistance and prospects are summarized.

Synergistic interaction between molybdenum disulfide nanosheet and metal organic framework for high performance supercapacitor.. [DOI: 10.21203/rs.3.rs-3263864/v1] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

Zeolitic imidazolate framework-67 crystals (ZIF-67) anchored molybdenum disulfide nanosheets (MS) have been synthesized via a hydrothermal approach followed by a simple chemical method. MS concentration has been varied to investigate its impact on the electrochemical efficiency within the electrode nanocomposite. The shiny spot of this composite is the combination of two desirable properties, the conductive path created by MS, and the structural framework support provided by Zeolitic imidazolate framework-67 intercalated with nickel (Z67.Ni). The reason behind this choice of this specific nanocomposite is the framework of the Z67.Ni that prevents MS nanosheets from restacking during the repeated charge and discharge cycles. Superior electrochemical behavior of Z67.Ni with 70% weight percent of MS (Z67.Ni/MS7) demonstrated the excellent synergistic effect between Z67.Ni crystals and MS nanosheets. It has a specific capacitance of 308.5 F g− 1 at 1 A g− 1 and delivers an excellent energy density (Ed) of 83.98 W h kg− 1 with a power density (Pd) of 2.78 kW kg− 1. These excellent results demonstrate the high efficiency of this nanocomposite material in supercapacitor applications.

Molybdenum Disulfide/Nickel-Metal Organic Framework Hybrid Nanosheets Based Disposable Electrochemical Sensor for Determination of 4-Aminophenol in Presence of Acetaminophen

The toxicity of commonly used drugs, such as acetaminophen (ACAP) and its degradation-derived metabolite of 4-aminophenol (4-AP), underscores the need to achieve an effective approach in their simultaneous electrochemical determination. Hence, the present study attempts to introduce an ultra-sensitive disposable electrochemical 4-AP and ACAP sensor based on surface modification of a screen-printed graphite electrode (SPGE) with a combination of MoS₂ nanosheets and a nickel-based metal organic framework (MoS₂/Ni-MOF/SPGE sensor). A simple hydrothermal protocol was implemented to fabricate MoS₂/Ni-MOF hybrid nanosheets, which was subsequently tested for properties using valid techniques including X-ray diffraction (XRD), field emission-scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX), Fourier transformed infrared spectroscopy (FTIR), and N₂ adsorption-desorption isotherm. The 4-AP detection behavior on MoS₂/Ni-MOF/SPGE sensor was followed by cyclic voltammetry (CV), chronoamperometry and differential pulse voltammetry (DPV). Our experimental findings on the generated sensor confirmed a broad linear dynamic range (LDR) for 4-AP from 0.1 to 600 μM with a high sensitivity of 0.0666 μA/μM and a low limit of detection (LOD) of 0.04 μM. In addition, an analysis of real specimens such as tap water sample as well as a commercial sample (acetaminophen tablets) illuminated the successful applicability of as-developed sensor in determining ACAP and 4-AP, with an impressive recovery rate.

Synthesis of Ni3S2 and MOF-Derived Ni(OH)2 Composite Electrode Materials on Ni Foam for High-Performance Supercapacitors

Honeycomb-like Ni(OH)₂/Ni₃S₂/Ni foam (NF) was fabricated via a two-step hydrothermal process and subsequent alkalization. Ni₃S₂ with a honeycombed structure was in-situ synthesized on the NF surface by a hydrothermal process. MOF-derived Ni(OH)₂ nanosheets were then successfully grown on the Ni₃S₂/NF surface by a second hydrothermal process and alkaline treatment, and a large number of nanosheets were interconnected to form a typical honeycomb-like structure with a large specific surface area and porosity. As a binder-free electrode, the prepared honeycomb-like Ni(OH)₂/Ni₃S₂/NF exhibited a high specific capacitance (2207 F·g^-1 at 1 A·g^-1, 1929.7 F·g^-1 at 5 mV·s^-1) and a remarkable rate capability and cycling stability, with 62.3% of the initial value (1 A·g^-1) retained at 10 A·g^-1 and 90.4% of the initial value (first circle at 50 mV·s^-1) retained after 5000 cycles. A hybrid supercapacitor (HSC) was assembled with Ni(OH)₂/Ni₃S₂/NF as the positive electrode and activated carbon (AC) as the negative electrode and exhibited an outstanding energy density of 24.5 Wh·kg^-1 at the power density of 375 W·kg^-1. These encouraging results render the electrode a potential candidate for energy storage.

Recent advances in the electrochemical applications of Ni-based metal organic frameworks (Ni-MOFs) and their derivatives

Nickel-based metal-organic skeletal materials (Ni-MOFs) are a new class of inorganic materials that have aroused attention of investigators during past couple of years. They offer advantages such as high specific surface area, structural diversity, tunable framework etc. This assorted class of materials exhibited catalytic activity and electrochemical properties and display wide range of applications in the fields of electrochemical sensing, electrical energy storage and electrocatalysis. In this context, the presented review focuses on strategies to improve the electrochemical performance and stability of Ni-MOFs through the optimization of synthesis conditions, the construction of composite materials, and the preparation of derivatives of precursors. The review also presents the applications of Ni-MOFs and their derivatives as electrochemical sensors, energy storage devices, and electrocatalysts. In addition, the challenges and further electrochemical development prospects of Ni-MOFs have been discussed.

Gate-Modulated High-Response Field-Effect Transistor-Type Gas Sensor Based on the MoS2/Metal-Organic Framework Heterostructure

The high surface-to-volume ratio and decent material properties of two-dimensional (2D) transition metal dichalcogenides (TMDs) make them advantageous as an active channel in field-effect transistor (FET)-type gas sensing devices. However, most existing TMD gas sensors are based on a two-terminal resistance-type structure and suffer from low responsivity and slow response, which has urged materials optimization as well as device engineering. Metal-organic frameworks (MOFs) have a large number of ordered binding sites in the pores that can specifically bind to gas molecules and can be decorated on TMD surfaces to enhance gas sensing capabilities. In this work, we successfully realize the FET-type gas sensor with MoS₂-MOF as the channel. The fabricated gas sensor exhibits enhanced NH₃ sensing performance (22.475 times higher in responsivity) as compared to the device with a bare MoS₂ channel. In addition, the FET-type gas sensor geometry enables effective tuning of sensitivity through electrical gating based on the modulation over the channel carrier concentration. Furthermore, the dependence of responsivity on the MoS₂ thickness is investigated as well to achieve an in-depth understanding of the electrical modulation mechanism of the MOF-decorated MoS₂ gas sensors. The demonstrated results can pave an attractive pathway toward the realization of advanced high-response and tunable TMD-based gas sensing devices.

Potential Applications of Nickel-Based Metal-Organic Frameworks and their Derivatives

Metal-Organic Frameworks (MOFs), a novel class of porous extended crystalline structures, are favored in different fields of heterogeneous catalysis, CO₂ separation and conversion, and energy storage (supercapacitors) due to their convenience of synthesis, structural tailor-ability, tunable pore size, high porosity, large specific surface area, devisable structures, and adjustable compositions. Nickel (Ni) is a ubiquitous element extensively applied in various fields of catalysis and energy storage due to its low cost, high abundance, thermal and chemical stability, and environmentally benign nature. Ni-based MOFs and their derivatives provide us with the opportunity to modify different properties of the Ni center to improve their potential as heterogeneous catalysts or energy storage materials. The recent achievements of Ni-MOFs and their derivatives as catalysts, membrane materials for CO₂ separation and conversion, electrode materials and their respective performance have been discussed in this review.

An iron based organic framework coated with nickel hydroxide for energy storage, conversion and detection

Although electrode materials based on metal organic frameworks (MOFs) were widely studied in the electrochemistry field, the origin of poor conductivity is still a bottleneck restricting their development. Herein, we constructed a conductive circuit by growing a layer of hydroxide on the surface of the Fe-MOF, and composite materials (Fe-MOF@Ni(OH)₂) are applied in the fields of supercapacitor, OER, and electrochemical sensing. Fe-MOF@Ni(OH)₂ not only maintains the intrinsic advantages of Fe-MOF, but also improves the electrical conductivity. Fe-MOF@Ni(OH)₂ exhibits a high specific capacity of 188 mAh g^-1 at 1 A g^-1 . The energy density of the asymmetric supercapacitor (Fe-MOF@Ni(OH)₂-20//AC) reaches 67.1 Wh kg^-1. During the oxygen evolution reaction, the overpotential of the material is 280 mV at 10 mA cm^-2, and the Tafel slope is 37.6 mV dec^-1. The electrochemical sensing tests showed the detection limit of BPA is 5 μM. Hence, these results provide key insights into the design of multifunctional electrode materials.