Protein-resistant polyurethane prepared by surface-initiated atom transfer radical graft polymerization (ATRgP) of water-soluble polymers: Effects of main chain and side chain lengths of grafts

The Structural Dispersity of Oligoethylene Glycol-Containing Polymer Brushes Determines Their Interfacial Properties

Ought to their bioinert properties and facile synthesis, poly[(oligoethylene glycol)methacrylate]s (POEGMAs) have been raised as attractive alternatives to poly(ethylene glycols) (PEGs) in an array of (bio)material applications, especially when they are applied as polymer brush coatings. However, commercially available OEG-methacrylate (macro)monomers feature a broad distribution of OEG lengths, thus generating structurally polydisperse POEGMAs when polymerized through reversible deactivation radical polymerization. Here, we demonstrate that the interfacial physicochemical properties of POEGMA brushes are significantly affected by their structural dispersity, i.e., the degree of heterogeneity in the length of side OEG segments. POEGMA brushes synthesized from discrete (macro)monomers obtained through chromatographic purification of commercial mixtures show increased hydration and reduced adhesion when compared to their structurally polydisperse analogues. The observed alteration of interfacial properties is directly linked to the presence of monodisperse OEG side chains, which hamper intramolecular and intermolecular hydrophobic interactions while simultaneously promoting the association of water molecules. These phenomena provide structurally homogeneous POEGMA brushes with a more lubricious and protein repellent character with respect to their heterogeneous counterparts. More generally, in contrast to what has been assumed until now, the properties of POEGMA brushes cannot be anticipated while ruling out the effect of dispersity by (macro)monomer feeds. Simultaneously, side chain dispersity of POEGMAs emerges as a critical parameter for determining the interfacial characteristics of brushes.

The effect of comb length on the in vitro and in vivo properties of self-assembled poly(oligoethylene glycol methacrylate)-based block copolymer nanoparticles

Comb copolymer analogues of poly(lactic acid)-polyethylene glycol block copolymers (PLA-b-PEG) offer potential to overcome the inherent chemistry and stability limitations of their linear block copolymer counterparts. Herein, we examine the differences between P(L)LA10K-b-PEG10K and linear-comb copolymer analogues thereof in which the linear PEG block is replaced by poly(oligo(ethylene glycol) methacrylate) (POEGMA) blocks with different side chain (comb) lengths but the same overall molecular weight. P(L)LA10K-b-POEGMA47510K and P(L)LA10K-b-POEGMA200010K block copolymers were synthesized via activators regenerated by electron transfer atom transfer radical polymerization (ARGET ATRP) and fabricated into self-assembled nanoparticles using flash nanoprecipitation via confined impinging jet mixing. Linear-comb copolymer analogues based on PLA-b-POEGMA yielded smaller but still well-controlled nanoparticle sizes (88 ± 2 nm and 114 ± 1 nm respectively compared to 159 ± 2 nm for P(L)LA10K-b-PEG10K nanoparticles) that exhibited improved colloidal stability relative to linear copolymer-based nanoparticles over a 15 day incubation period while maintaining comparably high cytocompatibility, although the comb copolymer analogues had somewhat lower loading capacity for doxorubicin hydrochloride. Cell spheroid studies showed that the linear-comb copolymers promoted enhanced tumor transport and thus cell killing compared to conventional linear block copolymers. In vivo studies showed all NP types could passively accumulate within implanted CT26 tumors but with different accumulation profiles, with P(L)LA10K-b-POEGMA200010K NPs showing continuous accumulation throughout the full 24 h monitoring period whereas tumor accumulation of P(L)LA10K-b-POEGMA47510K NPs was significant only between 8 h and 24 h. Overall, the linear-comb copolymer analogues exhibited superior stability, biodistribution, spheroid penetration, and inherent tunability over linear NP counterparts.

Surface functionalization of polyurethanes: A critical review

Synthetic polymers, particularly polyurethanes (PUs), have revolutionized bioengineering and biomedical devices due to their customizable mechanical properties and long-term stability. However, the inherent hydrophobic nature of PU surfaces arises common issues such as high friction, strong protein adsorption, and thrombosis, especially in the physiological environment of blood contact. To overcome these issues, researchers have explored various modification techniques to improve the surface biofunctionality of PUs. In this review, we have systematically summarized several typical surface modification methods including surface plasma modification, surface oxidation-induced grafting polymerization, isocyanate-based chemistry coupling, UV-induced surface grafting polymerization, adhesives-assisted attachment strategy, small molecules-bridge grafting, solvent evaporation technique, and hydrogen bonding interaction. Correspondingly, the advantages, limitations, and future prospects of these surface modification methods were discussed. This review provides an important guidance or tool for developing surface functionalized PUs in the fields of bioengineering and medical devices.

Antifouling silicone hydrogel contact lenses via densely grafted phosphorylcholine polymers

Silicone hydrogel contact lenses (CLs) permit increased oxygen permeability through their incorporation of siloxane functional groups. However, contact lens biofouling can be problematic with these materials; surface modification to increase lens compatibility is necessary for acceptable properties. This work focuses on the creation of an antifouling CL surface through a novel grafting method. A polymer incorporating 2-methacryloyloxyethyl phosphorylcholine (MPC), well known for its antifouling and biomimetic properties, was grafted to the model lens surfaces using surface-initiated atom transfer radical polymerization (SI-ATRP). The SI-ATRP modification generated a unique double-grafted polymeric architecture designed to resist protein adsorption through the presence of a surrounding hydration layer due to the PC groups and steric repulsion due to the density of the grafted chains. The polymer was grafted from model silicone hydrogel CL using a four-step SI-ATRP process. Attenuated total reflectance-Fourier transform infrared spectroscopy and XPS were used to confirm the surface chemical composition at each step of the synthesis. Both the surface wettability and equilibrium water content of the materials increased significantly upon polyMPC modification. The surface water contact angle was as low as 16.04 ± 2.37° for polyMPC-50 surfaces; complete wetting (∼0°) was observed for polyMPC-100 surfaces. A decrease in the protein adsorption by as much as 83% (p < 0.000 36) for lysozyme and 73% (p < 0.0076) for bovine serum albumin was observed, with no significant difference between different polyMPC chain lengths. The data demonstrate the potential of this novel modification process for the creation of extremely wettable and superior antifouling surfaces, useful for silicone hydrogel CL surfaces.

Architectural Modification of Conformal PEG-Bottlebrush Coatings Minimizes Anti-PEG Antigenicity While Preserving Stealth Properties

Poly(ethylene glycol) (PEG), a linear polymer known for its "stealth" properties, is commonly used to passivate the surface of biomedical implants and devices, and it is conjugated to biologic drugs to improve their pharmacokinetics. However, its antigenicity is a growing concern. Here, the antigenicity of PEG is investigated when assembled in a poly(oligoethylene glycol) methacrylate (POEGMA) "bottlebrush" configuration on a planar surface. Using ethylene glycol (EG) repeat lengths of the POEGMA sidechains as a tunable parameter for optimization, POEGMA brushes with sidechain lengths of two and three EG repeats are identified as the optimal polymer architecture to minimize binding of anti-PEG antibodies (APAs), while retaining resistance to nonspecific binding by bovine serum albumin and cultured cells. Binding of backbone- versus endgroup-selective APAs to POEGMA brushes is further investigated, and finally the antigenicity of POEGMA coatings is assessed against APA-positive clinical plasma samples. These results are applied toward fabricating immunoassays on POEGMA surfaces with minimal reactivity toward APAs while retaining a low limit-of-detection for the analyte. Taken together, these results offer useful design concepts to reduce the antigenicity of polymer brush-based surface coatings used in applications involving human or animal matrices.

2-methoxyethylacrylate modified polyurethane membrane and its blood compatibility

Hydrophilic material 2-methoxyethylacrylate (MEA) was grafted onto polyurethane (PU) membrane via Michael addition reaction. Fourier transform infrared spectroscope (FTIR) and X-ray photoelectron spectroscopy (XPS) characterizations of the modified membrane proved that MEA was successfully grafted onto PU membrane surface. The water contact angle of the modified PU membrane decreased from 86° to 48° compared with unmodified PU membrane, which means that the hydrophilicity of the modified membrane was greatly improved. A series of blood compatibility tests including bovine serum protein adsorption, platelet adhesion, hemolysis assay, plasma recalacification time, prothrombin time (PT), partial thromboplastin time (APTT) and thrombin time (TT) were carried out on PU membrane and the modified PU membrane with highest grafted density of MEA. The combined results indicate that MEA plays an important role in improving the blood compatibility of PU membrane.

Poly(oligo(ethylene glycol) methyl ether methacrylate) Brushes on High-κ Metal Oxide Dielectric Surfaces for Bioelectrical Environments

Advances in electronics and life sciences have generated interest in "lab-on-a-chip" systems utilizing complementary metal oxide semiconductor (CMOS) circuitry for low-power, portable, and cost-effective biosensing platforms. Here, we present a simple and reliable approach for coating "high-κ" metal oxide dielectric materials with "non-fouling" (protein- and cell-resistant) poly(oligo(ethylene glycol) methyl ether methacrylate (POEGMA) polymer brushes as biointerfacial coatings to improve their relevance for biosensing applications utilizing advanced electronic components. By using a surface-initiated "grafting from" strategy, POEGMA films were reliably grown on each material, as confirmed by ellipsometric measurements and X-ray photoelectron spectroscopy (XPS) analysis. The electrical behavior of these POEGMA films was also studied to determine the potential impact on surrounding electronic devices, yielding information on relative permittivity and breakdown field for POEGMA in both dry and hydrated states. We show that the incorporation of POEGMA coatings significantly reduced levels of nonspecific protein adsorption compared to uncoated high-κ dielectric oxide surfaces as shown by protein resistance assays. These attributes, combined with the robust dielectric properties of POEGMA brushes on high-κ surfaces open the way to incorporate this protein and cell resistant polymer interface into CMOS devices for biomolecular detection in a complex liquid milieu.

Surface-Initiated Controlled Radical Polymerization: State-of-the-Art, Opportunities, and Challenges in Surface and Interface Engineering with Polymer Brushes

The generation of polymer brushes by surface-initiated controlled radical polymerization (SI-CRP) techniques has become a powerful approach to tailor the chemical and physical properties of interfaces and has given rise to great advances in surface and interface engineering. Polymer brushes are defined as thin polymer films in which the individual polymer chains are tethered by one chain end to a solid interface. Significant advances have been made over the past years in the field of polymer brushes. This includes novel developments in SI-CRP, as well as the emergence of novel applications such as catalysis, electronics, nanomaterial synthesis and biosensing. Additionally, polymer brushes prepared via SI-CRP have been utilized to modify the surface of novel substrates such as natural fibers, polymer nanofibers, mesoporous materials, graphene, viruses and protein nanoparticles. The last years have also seen exciting advances in the chemical and physical characterization of polymer brushes, as well as an ever increasing set of computational and simulation tools that allow understanding and predictions of these surface-grafted polymer architectures. The aim of this contribution is to provide a comprehensive review that critically assesses recent advances in the field and highlights the opportunities and challenges for future work.

Well-defined polyurethane-graft-poly(N,N-dimethylacrylamide) copolymer with a controlled graft density and grafted chain length: synthesis and its application as a Pickering emulsion

Well-defined PU-g-PDMA graft copolymers with controlled graft densities and grafted chain lengths could be facilely synthesized by combining the polyaddition reaction with the RAFT polymerization.

Degradable polyurethane with poly(2-ethyl-2-oxazoline) brushes for protein resistance

The effects of chain length and graft density of poly(2-ethyl-2-oxazoline) on the protein resistance of degradable polyurethane-graft-poly(2-ethyl-2-oxazoline) with PCL as the soft segment have been investigated.

Surface tailoring for selective endothelialization and platelet inhibition via a combination of SI-ATRP and click chemistry using Cys-Ala-Gly-peptide

Surface tailoring is an attractive approach to enhancing selective endothelialization, which is a prerequisite for current vascular prosthesis applications. Here, we modified polycarbonate urethane (PCU) surface with both poly(ethylene glycol) and Cys-Ala-Gly-peptide (CAG) for the purpose of creating a hydrophilic surface with targeting adhesion of endothelial cells (ECs). In the first step, PCU-film surface was grafted with poly(ethylene glycol) methacrylate (PEGMA) to covalently tether hydrophilic polymer brushes via surface initiated atom transfer radical polymerization (SI-ATRP), followed by grafting of an active monomer pentafluorophenyl methacrylate (PFMA) by a second ATRP. The postpolymerization modification of the terminal reactive groups with allyl amine molecules created pendant allyl groups, which were subsequently functionalized with cysteine terminated CAG-peptide via photo-initiated thiol-ene click chemistry. The functionalized surfaces were characterized by water contact angle and XPS analysis. The growth and proliferation of human ECs or human umbilical arterial smooth muscle cells on the functionalized surfaces were investigated for 1, 3 and 7 day/s. The results indicated that these peptide functionalized surfaces exhibited enhanced EC adhesion, growth and proliferation. Furthermore, they suppressed platelet adhesion in contact with platelet-rich plasma for 2h. Therefore, these surfaces with EC targeting ligand could be an effective anti-thrombogenic platform for vascular tissue engineering application.

Surface modification with polyethylene glycol-corn trypsin inhibitor conjugate to inhibit the contact factor pathway on blood-contacting surfaces

Blood contacting surfaces bind plasma proteins and trigger coagulation by activating factor XII (FXII). The objective of this work was to develop blood contacting surfaces having the dual properties of protein resistance and inhibition of coagulation. Gold was used as a model substrate because it is amenable to facile modification using gold-thiol chemistry and to detailed surface characterization. The gold was modified with both polyethylene glycol (PEG) and corn trypsin inhibitor (CTI), a potent and specific inhibitor of activated FXII (FXIIa). Two methods of surface modification were developed; sequential and direct. In the sequential method PEG was first chemisorbed on gold; CTI was then attached to the PEG. In the direct method a conjugate of PEG and CTI was first prepared; the conjugate was then immobilized on gold. The surfaces were characterized by water contact angle and XPS. Biointeractions with the modified surfaces were assessed by measuring fibrinogen adsorption from buffer and plasma and by immunoblot analysis of eluted proteins after plasma exposure. Inhibition of FXIIa, autoactivation of FXII, and clotting times of plasma in contact with the surfaces were also measured. Both the sequential and direct surfaces showed reduced protein adsorption, increased FXIIa inhibition and longer clotting times compared with controls. Although the CTI density was lower on surfaces prepared using the sequential method, surfaces so prepared exhibited greater CTI activity than those generated by the direct method. It is concluded that the activity of immobilized PEG-CTI depends on the method of attachment and that immobilized CTI may be useful in rendering biomaterials more blood compatible.

ATRP grafting of oligo(ethylene glycol) methacrylates from gold surface — Effect of monomer size on grafted chain and EO unit densities

Oligo(ethylene glycol) methacrylate (OEGMA) was grafted from Au surface via surface-initiated atom-transfer radical polymerization (s-ATRP). The initiator density was adjusted by the mole fractions of surface-attachable ATRP initiator and diluting agent. Three OEGMA monomers of Mr 300, 475, and 1100 were used. The Au surfaces before and after modification were characterized by water contact angle and ellipsometry. The effect of monomer Mr and initiator density on surface chain density and EO unit density was investigated. It was found that at low initiator density (mole fraction of initiator of 2%–5%), poly(OEGMA) grafts had comparable surface chain density independent of OEGMA Mr. However, at high initiator density (mole fraction of initiator >10%), poly(OEGMA)1100 had obviously lower chain densities than poly(OEGMA)300 and poly(OEGMA)475, which could be attributed to the size difference of the monomers. The short chain length and low surface chain density of poly(OEGMA)1100 resulted in its relatively low surface EO unit density.

Biocompatible, hyaluronic acid modified silicone elastomers

Although silicones possess many useful properties as biomaterials, their hydrophobicity can be problematic. To a degree, this issue can be addressed by surface modification with hydrophilic polymers such as poly(ethylene glycol), but the resulting structures are usually not conducive to cell growth. In the present work, we describe the synthesis and characterization of covalently linked hyaluronic acid (HA) (35 kDa) to poly(dimethylsiloxane) (PDMS) elastomer surfaces. HA is of interest because of its known biological properties; its presence on a surface was expected to improve the biocompatibility of silicone materials for a wide range of bioapplications. HA was introduced with a coupling agent in two steps from high-density, tosyl-modified, poly(ethylene glycol) tethered silicone surfaces. All materials synthesized were characterized by water contact angle, ATR-FTIR, XPS and (13)C solid state NMR spectroscopy. Biological interactions with these modified silicone surfaces were assessed by examining interactions with fibrinogen as a model protein as well as determining the in vitro response of fibroblast (3T3) and human corneal epithelial cells relative to unmodified poly(dimethylsiloxane) controls. The results suggest that HA modification significantly enhances cell interactions while decreasing protein adsorption and may therefore be effective for improving biocompatibility of PDMS and other materials.