Effect of calcium ions on the evolution of biofouling by Bacillus subtilis in plate heat exchangers simulating the heat pump system used with treated sewage in the 2008 Olympic Village

Biofilm Formation by Mutant Strains of Bacilli under Different Stress Conditions

Bacillus subtilis is traditionally classified as a PGPR that colonizes plant roots through biofilm formation. The current study focused on investigating the influence of various factors on bacilli biofilm formation. In the course of the study, the levels of biofilm formation by the model strain B. subtilis WT 168 and on its basis created regulatory mutants, as well as strains of bacilli with deleted extracellular proteases under conditions of changes in temperature, pH, salt and oxidative stress and presence of divalent metals ions. B. subtilis 168 forms halotolerant and oxidative stress-resistant biofilms at a temperature range of 22 °C-45 °C and a pH range of 6-8.5. The presence of Ca2+, Mn2+ and Mg2+ upsurges the biofilm development while an inhibition with Zn2+. Biofilm formation level was higher in protease-deficient strains. Relative to the wild-type strain, degU mutants showed a decrease in biofilm formation, abrB mutants formed biofilms more efficiently. spo0A mutants showed a plummeted film formation for the first 36 h, followed by a surge after. The effect of metal ions and NaCl on the mutant biofilms formation is described. Confocal microscopy indicated that B. subtilis mutants and protease-deficient strains differ in matrix structure. The highest content of amyloid-like proteins in mutant biofilms was registered for degU-mutants and protease-deficient strains.

Bacterial surface attachment and fouling assay on polymer and carbon surfaces using Rheinheimera sp. identified using bacteria community analysis of brackish water

Biofouling on surfaces in contact with sea- or brackish water can severely impact the function of devices like reverse osmosis modules. Single species laboratory assays are frequently used to test new low fouling materials. The choice of bacterial strain is guided by the natural population present in the application of interest and decides on the predictive power of the results. In this work, the analysis of the bacterial community present in brackish water from Mashabei Sadeh, Israel was performed and Rheinheimera sp. was detected as a prominent microorganism. A Rheinheimera strain was selected to establish a short-term accumulation assay to probe initial bacterial attachment as well as biofilm growth to determine the biofilm-inhibiting properties of coatings. Both assays were applied to model coatings, and technically relevant polymers including laser-induced graphene. This strategy might be applied to other water sources to better predict the fouling propensity of new coatings.

Assessment of the Impact of Temperature on Biofilm Composition with a Laboratory Heat Exchanger Module

Temperature change over the length of heat exchangers might be an important factor affecting biofouling. This research aimed at assessing the impact of temperature on biofilm accumulation and composition with respect to bacterial community and extracellular polymeric substances. Two identical laboratory-scale plate heat exchanger modules were developed and tested. Tap water supplemented with nutrients was fed to the two modules to enhance biofilm formation. One “reference” module was kept at 20.0 ± 1.4 °C and one “heated” module was operated with a counter-flow hot water stream resulting in a bulk water gradient from 20 to 27 °C. Biofilms were grown during 40 days, sampled, and characterized using 16S rRNA gene amplicon sequencing, EPS extraction, FTIR, protein and polysaccharide quantifications. The experiments were performed in consecutive triplicate. Monitoring of heat transfer resistance in the heated module displayed a replicable biofilm growth profile. The module was shown suitable to study the impact of temperature on biofouling formation. Biofilm analyses revealed: (i) comparable amounts of biofilms and EPS yield in the reference and heated modules, (ii) a significantly different protein to polysaccharide ratio in the EPS of the reference (5.4 ± 1.0%) and heated modules (7.8 ± 2.1%), caused by a relatively lower extracellular sugar production at elevated temperatures, and (iii) a strong shift in bacterial community composition with increasing temperature. The outcomes of the study, therefore, suggest that heat induces a change in biofilm bacterial community members and EPS composition, which should be taken into consideration when investigating heat exchanger biofouling and cleaning strategies. Research potential and optimization of the heat exchanger modules are discussed.

Encapsulation of two fermentation agents, Lactobacillus sakei and calcium ions in microspheres

Alginate microspheres loaded with two fermentation active agents, calcium cations and strain LS0296 identified as Lactobacillus sakei, have been prepared and characterized. The role of calcium cation is twofold, it acts as gelling cation and as fermentation active agent. Encapsulation and the presence of calcium ions in the same compartment do not inhibit the activity of LS0296. Molecular interactions in microspheres are complex, including mainly hydrogen bonds and electrostatic interactions. In vitro calcium cations and strain LS0296 release profiles were fitted to the Korsmeyer-Peppas empirical model. The calcium cation release process is driven at first by Fickian diffusion through microspheres and then by anomalous transport kinetics. The in vitro LS0296 release process is driven by Fickian diffusion through microspheres showing a much slower releasing rate than calcium cations. The release of LS0296 strain is followed by a decrease in the pH value. Results obtained give us a new insight into complex interactions between bacterial cultures and microsphere constituents. Prepared formulations of calcium alginate microspheres loaded with LS0296 could be used as a new promising tool and a model for different starter cultures encapsulation and use in the production of fermented foods.

Characterization of the Evolution of Crystallization Fouling in Membranes

Liquid-to-air membrane energy exchangers (LAMEEs) are promising in heating, ventilating, and air-conditioning applications because they are able to use semipermeable membranes to transfer heat and moisture between air and liquid desiccant streams. However, the development of crystallization fouling in membranes may pose a great risk to the long-term performance of LAMEEs. The main aim of this paper is to characterize the evolution of crystallization fouling in membranes through the use of both noninvasive and invasive methods. Noninvasive methods are used to study the development of fouling in the LAMEE by monitoring the changes in moisture flux through the membrane and overall moisture-transfer resistance of the LAMEE. On the other hand, invasive methods are implemented to characterize fouled membranes by using optical microscopy and scanning electron microscopy (SEM) to depict the morphology of crystal deposits and energy-dispersive X-ray spectroscopy (EDX) to identify the composition of the deposits. Experiments are performed by using air to dehydrate MgCl₂(aq) at two operating conditions of low and high fouling rates. The results show that the moisture flux decreases and the moisture-transfer resistance increases more considerably during the test at the high fouling rate than in the test at the low fouling rate. SEM micrographs show that cake crystal deposits cover the membrane surface in the test at the high fouling rate, whereas only few crystal particles are observed on the membrane in the test at the low fouling rate. Furthermore, the crystal deposits undergo more structural changes in the tests at the high fouling rate than in the tests at the low fouling rate, possibly because of the higher moisture transfer rate through the membrane in the tests at the high fouling rate. Finally, the SEM-EDX analysis confirms that the crystal deposits primarily consist of Mg, Cl, and O elements.

Using micro-patterned surfaces to inhibit settlement and biofilm formation by Bacillus subtilis

Biofilm is a biological complex caused by bacteria attachment to the substrates and their subsequent reproduction and secretion. This phenomenon reduces heat transfer efficiency and causes significant losses in treated sewage heat-recovering systems. This paper describes a physical approach to inhibit bacteria settlement and biofilm formation by Bacillus subtilis, which is the dominant species in treated sewage. Here, micro-patterned surfaces with different characteristics (stripe and cube) and dimensions (1-100 μm) were fabricated as surfaces of interest. Model sewage was prepared and a rotating coupon device was used to form the biofilms. Precision balance, scanning electron microscopy, and confocal laser scanning microscopy (CLSM) were employed to investigate the inhibitory effects and the mechanisms of the biofilm-surface interactions. The results have shown that surfaces with small pattern sizes (1 and 2 μm) all reduced biofilm formation significantly. Interestingly, the CLSM images showed that the surfaces do not play a role in "killing" the bacteria. These findings are useful for future development of new process surfaces on which bacteria settlement and biofilm formation can be inhibited or minimized.

Antibacterial and anti-biofilm efficacy of fluoropolymer coating by a 2,3,5,6-tetrafluoro-p-phenylenedimethanol structure

Fluorinated polymers generally function as antibacterial agents, but their anti-biofilm effect remains unresolved. This study investigates the efficacy of fluoropolymers containing 2,3,5,6-tetrafluoro-p-phenylenedimethanol (TFPDM) in preventing biofilm formation by Bacillus subtilis and Escherichia coli (Gram-positive and Gram-negative bacterial species). To this end, TFPDM-based acrylate and epoxy polymers (AF and EF, respectively) and their structural analogues without TFPDM (A and E, respectively) were synthesized. All polymers were coated onto polyethylene terephthalate (PET) sheets. Relative to pristine PET, sheets coated with AF reduced the initial bacterial adhesion (72h) and biofilm formation (30days) of B. subtilis by 27.6% and 68.7% and of E. coli by 89.2% and 93.8%, respectively. The comparable antibacterial and anti-biofilm efficacies were obtained by sheets with EF. The biofilm detachment was substantially facilitated from the AF, compared with the structural analogue without TFPDM (A). In this comprehensive study, the bacterial adhesion and subsequent biofilm formation were prevented by TFPDM-containing polymers effectively.

Study on interactions between suspended matter and biofouling formed by treated sewage

Heat exchangers used for treated sewage energy recovery usually suffer from the composite fouling problem, which seriously impairs the heat transfer efficiency. Treated sewage heat exchanger composite fouling is mostly composed of biofouling and is notably affected by interactions between the biofouling and suspended matter. Experiments were performed using simulated treated sewage and two kinds of simulated suspended matter, silicon dioxide particles and polyamide filaments, to model the interactions. Different flow velocities, particle sizes and concentrations were tested with their influences presented by the fouling wet weight changes. Empirical equation and threshold were developed based on the results to predict whether the suspended matter promotes or impedes fouling growth. The results indicate that proper control of the flow velocities, particle sizes and concentrations of suspended matter using empirical equation and threshold can inhibit fouling by reducing unwanted positive interactions and promoting beneficial negative interactions. The filament interactions were analysed and the unique attachment mechanisms of filaments were discussed for the first time.

Experimental investigation of interactions between the temperature field and biofouling in a synthetic treated sewage stream

Biofouling causes significant losses in efficiency in heat exchangers recovering waste heat from treated sewage. The influence of the temperature field on biofouling was investigated using a flat plate heat exchanger which simulated the channels in a plate and frame unit. The test surface was a 316 stainless steel plate, and a solution of Bacillus sp. and Aeromonas sp. was used as a model process liquid. The test cell was operated under co-current, counter-current, and constant wall temperature configurations, which gave different temperature distributions. Biofouling was monitored via changes in heat transfer and biofilm thickness. The effect of uniform temperature on biofouling formation was similar to the effect of uniform temperature on planktonic growth of the organisms. Further results showed that the temperature field, and particularly the wall temperature, influenced the rate of biofouling strongly. The importance of wall temperature suggests that fouling could be mitigated by using different configurations in summer and winter.