Ionisation effects on the permeation of pharmaceutical compounds through silicone membrane

Fabrication of Alginate-Based O/W Nanoemulsions for Transdermal Drug Delivery of Lidocaine: Influence of the Oil Phase and Surfactant

Transdermal drug delivery of lidocaine is a good choice for local anesthetic delivery. Microemulsions have shown great effectiveness for the transdermal transport of lidocaine. Oil-in-water nanoemulsions are particularly suitable for encapsulation of lipophilic molecules because of their ability to form stable and transparent delivery systems with good skin permeation. However, fabrication of nanoemulsions containing lidocaine to provide an extended local anesthetic effect is challenging. Hence, the aim of this study was to address this issue by employing alginate-based o/w nanocarriers using nanoemulsion template that is prepared by combined approaches of ultrasound and phase inversion temperature (PIT). In this study, the influence of system composition such as oil type, oil and surfactant concentration on the particle size, in vitro release and skin permeation of lidocaine nanoemulsions was investigated. Structural characterization of lidocaine nanoemulsions as a function of water dilution was done using DSC. Nanoemulsions with small droplet diameters (d < 150 nm) were obtained as demonstrated by dynamic light scattering (DLS) and cryo-TEM. These nanoemulsions were also able to release 90% of their content within 24-h through PDMS and pig skin and able to the drug release over a 48-h. This extended-release profile is highly favorable in transdermal drug delivery and shows the great potential of this nanoemulsion as delivery system.

Poly(dimethylsiloxane): A Sustainable Human Skin Alternative for Transdermal Drug Delivery Prediction

Despite the advantages of transdermal drug delivery (TDD), which makes it a fast-growing area of research in pharmaceutics, numerous challenges affect their development, which limits exploring the full potential of this alternate drug delivery route. In trying to address one of these problems, it is strongly believed that the need for a sustainable skin alternative is paramount. Efforts made in an attempt to provide a sustainable alternative to employing skin in pharmaceutical analysis, by better utilising a polymer membrane, namely poly(dimethylsiloxane), also known as PDMS are discussed. Several combined properties of this polymer, which includes its relative stability in comparison with human skin, make it a good candidate for the replacement of skin. Modifications undertaken to this polymer membrane (to create an enhanced skin mimic for permeation analysis) are discussed and reviewed in this paper, including the improved ability to predict permeability for both hydrophobic and hydrophilic drugs. Optimisations related to studying TDD including limitations encountered are also documented and reviewed. It is hoped that such developments in this field will ultimately lead to researchers replacing skin with optimised polymer-based alternatives to predict transdermal drug delivery.

Membrane Removal of Emerging Contaminants from Water: Which Kind of Membranes Should We Use?

Membrane technologies are nowadays widely used; especially various types of filtration or reverse osmosis in households, desalination plants, pharmaceutical applications etc. Facing water pollution, they are also applied to eliminate emerging contaminants from water. Incomplete knowledge directs the composition of membranes towards more and more dense materials known for their higher selectivity compared to porous constituents. This paper evaluates advantages and disadvantages of well-known membrane materials that separate on the basis of particle size, usually exposed to a large amount of water, versus dense hydrophobic membranes with target transport of emerging contaminants through a selective barrier. In addition, the authors present several membrane processes employing the second type of membrane.

The effect of the presence of biosurfactant on the permeation of pharmaceutical compounds through silicone membrane

The permeation of ten model drugs through silicone membrane was analysed to investigate the effect of the presence of a biosurfactant obtained from corn steep liquor. The ten selected pharmaceutical compounds were chosen to include a diverse range of physicochemical properties, such as variable hydrophobicities, pKa's, molecular masses and degrees of ionisation. When compared with compound permeation alone, the additional inclusion of biosurfactant in the donor phase altered the rate and extent of permeation. It significantly enhanced permeation for five of the compounds, whereas it decreased permeation for four of the compounds and remained approximately the same for the tenth compound. These effects were observed at both biosurfactant concentrations considered, namely 0.005 mg/mL, i.e. below the critical micellar concentration (CMC) and 0.500 mg/mL, i.e. above the CMC of the biosurfactant. Upon analysing permeation change with respect to physicochemical properties of the compounds, it was determined that compounds with a relative molecular mass below 200 resulted in an increase in permeation with biosurfactant present, and those above 200 resulted in a decrease in permeation with biosurfactant present. This effect was therefore attributed to the formation of a drug-biosurfactant interaction that enhanced permeation of smaller compounds, yet retarded permeation for those with a higher molecular mass. These in vitro findings can be considered an indication of potential novel formulation options that incorporate biosurfactant to create transdermal products that have bespoke permeation profiles.

The Physicochemical Characteristics of Prosthetic Materials and Their Influence on Their Clinical Properties

The use of elastic materials favours degradation of their surface. The period of their clinical usefulness is then shortened, and their further utilisation in the oral cavity may have the reverse effect. The surface properties of such material as well as the influence of the humidity on their surface are very important as they determine the prosthetic materials behavior in the mouth. The surface of such material should be resistant to water. Inverse gas chromatography is an accurate, sensitive technique for studying surface properties. Thanks to using a unique equipment specially designed for IGC technique, Surface Energy Analyzer, it was possible to characterize the surface at 0 and 80% of humidity. Our results show that increased humidity does not affect surface properties of studied prosthetic materials. Their ability to dispersive and specific interactions change in very limited degree. IGC experiment was also applied for the estimation of Hansen solubility parameters that indicate ability of a material to dispersive, polar, and hydrogen-bonding interactions. Relation between the surface characteristics and practical use of soft lining materials with implications for their clinical usefulness is also discussed.