Adsorption of lysozyme on base metal surfaces in the presence of an external electric potential

Electrode Potential-Dependent Studies of Protein Adsorption on Ti6Al4V Alloy

This article presents the potential-dependent adsorption of two proteins, bovine serum albumin (BSA) and lysozyme (LYZ), on Ti₆Al₄V alloy at pH 7.4 and 37 °C. The adsorption process was studied on an electropolished alloy under cathodic and anodic overpotentials, compared to the open circuit potential (OCP). To analyze the adsorption process, various complementary interface analytical techniques were employed, including PM-IRRAS (polarization-modulation infrared reflection-absorption spectroscopy), AFM (atomic force microscopy), XPS (X-ray photoelectron spectroscopy), and E-QCM (electrochemical quartz crystal microbalance) measurements. The polarization experiments were conducted within a potential range where charging of the electric double layer dominates, and Faradaic currents can be disregarded. The findings highlight the significant influence of the interfacial charge distribution on the adsorption of BSA and LYZ onto the alloy surface. Furthermore, electrochemical analysis of the protein layers formed under applied overpotentials demonstrated improved corrosion protection properties. These studies provide valuable insights into protein adsorption on titanium alloys under physiological conditions, characterized by varying potentials of the passive alloy.

Dielectric Spectroscopy can Predict the Effect of External AC Fields on the Dynamic Adsorption of Lysozyme

This report describes the application of dielectric spectroscopy as a simple and fast way to guide protein adsorption experiments. Specifically, the polarization behavior of a layer of adsorbed lysozyme was investigated using a triangular‐wave signal with frequencies varying from 0.5 to 2 Hz. The basic experiment, which can be performed in less than 5 min and with a single sample, not only allowed confirming the susceptibility of the selected protein towards the electric signal but also identified that this protein would respond more efficiently to signals with lower frequencies. To verify the validity of these observations, the adsorption behavior of lysozyme onto optically transparent carbon electrodes was also investigated under the influence of an applied alternating potential. In these experiments, the applied signal was defined by a sinusoidal wave with an amplitude of 100 mV and superimposed to +800 mV (applied as a working potential) and varying the frequency in the 0.1–10000 Hz range. The experimental data showed that the greatest adsorbed amounts of lysozyme were obtained at the lowest tested frequencies (0.1–1.0 Hz), results that are in line with the corresponding dielectric features of the protein.

Immobilization of surface non-affinitive protein onto a metal surface by an external electric field

We investigated an alternate technique to coat the surface with a protein having no surface affinity, without the use of any exotic chemical agents. An external electric field was utilized to prepare the protein coating on a metal substrate. Stainless steel (St) substrate and lysozyme (LSZ) were used as the surface to be coated and the model non-adsorptive protein, respectively. Dynamics of the adsorption of LSZ on the St surface in the presence and absence of an external electric potential (EEP) were monitored by in-situ ellipsometry. Applying negative surface potential (-0.4 V vs Ag/AgCl) forced the adsorption of LSZ onto the St surface where LSZ did not adsorb without applying any EEP. The repetition of the EEP-application and -cut-off indicated the controllability of the LSZ coating amount depending on the total duration of the EEP-application. The coated LSZ largely remained bound to the surface even by the cut-off of the external electric field, the ratio of which to the detached amount was roughly constant (approximately 7:3). Furthermore, the LSZ coated surface on the St substrate was found to be reversibly switched between being affinitive and non-affinitive to a typical model protein adsorbate (bovine serum albumin) by the EEP-application and cut-off.

Influence of an external electric field on removal of protein fouling on a stainless steel surface by proteolytic enzymes

Enzymatic cleaning is a potentially useful method for removing proteinaceous fouling from solid surfaces under mild conditions. Herein, the influence of an external electric field on the enzymatic cleaning of a metal surface fouled with a protein was investigated. The model fouling protein (BSA; lysozyme) was prepared on a stainless steel (St) surface, and the resulting surface subjected to enzymatic cleaning with an electric potential being applied to the St plate. Trypsin, α-chymotrypsin, and thermolysin were used as model proteases. The amounts of protein remaining on the plate before and during the cleaning process were measured by means of a reflection absorption technique using Fourier transform infrared spectroscopy. In the case for BSA fouling, the cleaning efficiency of the protease tended to increase at more negative applied potentials. Whereas, there was an optimum applied potential for removing the lysozyme fouling. Atomic force microscopy analyses indicated that applying an adequate range of electric potential enhanced the enzymatic removal of protein fouling inside scratches on the St plate surface. These findings suggest the existence of two modes of electrostatic interactions for the external electric field, one with protease molecules and the other with digested fragments of the fouling protein.