CT-based structural analyses of vertebral fractures with polymeric augmentation: A study of cadaveric three-level spine segments

Simulation of cancer progression in bone by a virtual thermal flux with a case study on lumbar vertebrae with multiple myeloma

BACKGROUND

Two main problems examining the mechanism of cancer progression in the tissues using the computational models are lack of enough knowledge on the effective factors for such events in vivo environments and lack of specific parameters in the available computational models to simulate such complicated reactions.

METHODS

In this study, it was tried to simulate the progression of cancerous lesions in the bone tissues by an independent parameter from the anatomical and physiological characteristics of the tissues, so to degrade the orthotropic mechanical properties of the bone tissues, a virtual temperature was determined to be used by a well-known framework for simulation of damages in the composite materials. First, the reliability of the FE model to simulate hyperelastic response in the intervertebral discs (IVDs) and progressive failure in the bony components were verified by simulation of some In-Vitro tests, available in the literature. Then, the progression of the osteolytic damage was simulated in a clinical case with multiple myeloma in the lumbar vertebrae.

RESULTS

The FE model could simulate stress-shielding and diffusion of lesion in the posterior elements of the damaged vertebra which led to spinal stenosis. The load carrying shares associated with the anterior half and the posterior half of the examined vertebral body and the posterior elements were estimated equal to 41 %, 47 % and 12 %, respectively for the intact condition, that changed to 14 %, 16 % and 70 %, when lesion occupied one third of the vertebral body.

CONCLUSION

Correlation of the FE results with the deformation shapes, observed in the MRIs for the clinical case study, indicated appropriateness of the procedure, proposed for simulation of the progressive osteolytic damage in the vertebral segments. The future studies may follow simulation of tumor growth for various metastatic tissues using the method, established here.

A novel device with pedicular anchorage provides better biomechanical properties than balloon kyphoplasty for the treatment of vertebral compression fractures

PURPOSE

To compare the biomechanical behavior of vertebrae with vertebral compression fractures (VCF) treated by a novel system with pedicular anchorage (dowelplasty) versus balloon kyphoplasty.

METHODS

Four cadaveric spines (T12-L5) were harvested, cleaned from soft tissues, and separated into vertebrae. Axial compressive loads were applied to each vertebra until a VCF was generated. Half of the vertebrae (n = 11) were instrumented using the "dowelplasty" system, consisting of a hollow titanium dowel anchored into the pedicle, through which a cannulated titanium nail is inserted and locked and through which cement is injected. The other half (n = 11) were instrumented using balloon kyphoplasty. Axial compressive loads were re-applied to each vertebra until fracture. Fracture load and fracture energy were calculated from load-displacement data for the pre- and post-treatment states.

RESULTS

Compared to balloon kyphoplasty, dowelplasty granted greater net change in fracture load (373N; 95%CI,-331-1076N) and fracture energy (755Nmm; 95%CI,-563-2072Nmm). A sensitivity analysis was performed without L4 and L5 vertebrae from the dowelplasty group, since the length of the cannulated nails was too short for these vertebrae: compared to balloon kyphoplasty, dowelplasty granted an even greater net change in fracture load (680N; 95%CI,-96-1457N) and fracture energy (1274Nmm; 95%CI,-233-2781Nmm).

CONCLUSION

Treating VCFs with dowelplasty grants increased fracture load and fracture energy compared to the pre-treatment state. Furthermore, dowelplasty grants greater improvement in fracture load and fracture energy compared to balloon kyphoplasty, which suggests that dowelplasty may be a good alternative for the treatment of VCF.

LEVEL OF EVIDENCE

level IV.

Single-level subject-specific finite element model can predict fracture outcomes in three-level spine segments under different loading rates

Osteoporosis-related vertebral compression fracture can occur under normal physiological activities. Bone metastasis is another source of vertebral fracture. Different loading rates, either high-energy traumas such as falls or low-energy traumas under normal physiological activities, can result in different fracture outcomes. The aim of the current study was to develop a quantitative computed tomography-based finite element analysis (QCT/FEA) technique for single vertebral bodies to predict fracture strength of three-level spine segments. Developed QCT/FEA technique was also used to characterize vertebral elastic moduli at two loading rates of 5 mm/min, representing a physiologic loading condition, and 12000 mm/min, representing a high-energy trauma. To this end, a cohort of human spine segments divided into three groups of intact, defect, and augmented were mechanically tested to fracture; then, experimental stiffness and fracture strength values were measured. Outcomes of this study showed no significant difference between the elastic modulus equations at the two testing speeds. Areal bone mineral density measured by dual x-ray absorptiometry (DXA/BMD) explained only 53% variability (R² = 0.53) in fracture strength outcomes. However, QCT/FEA could explain 70% of the variability (R² = 0.70) in experimentally measured fracture strength values. Adding disk degeneration grading, testing speed, and sex to QCT/FEA-estimated fracture strength values further increased the performance of our statistical model by 14% (adjusted R² of 0.84 between the prediction and experimental fracture forces). In summary, our results indicated that a single-vertebra model, which is computationally less expensive and more time efficient, is capable of estimating fracture outcomes with acceptable performance (range: 70-84%).