Heat evolution of alkali-activated materials: A review on influence factors

Proposed simplified methodological approach for designing geopolymer concrete mixtures

The development of geopolymer concrete offers promising prospects for sustainable construction practices due to its reduced environmental impact compared to conventional Portland cement concrete. However, the complexity involved in geopolymer concrete mix design often poses challenges for engineers and practitioners. In response, this study proposes a simplified approach for designing geopolymer concrete mixtures, drawing upon principles from Portland cement concrete mix design standards and recommended molar ratios of oxides involved in geopolymer synthesis. The proposed methodology aims to streamline the mix design process while optimizing key factors such as chemical composition, alkali activation solution, water content, and curing conditions to achieve desired compressive strength and workability. By leveraging commonalities between Portland cement concrete and geopolymer concrete, this approach seeks to facilitate the adoption of geopolymer concrete in practical construction applications. The proposed mix design guidelines have been validated through examples for concrete cured under different conditions, including outdoor and oven curing. Future research should focus on validating the proposed methodology through experimental studies and exploring cost-effective alternatives for alkali activation solutions to enhance the feasibility and scalability of geopolymer concrete production. Overall, the proposed simplified approach holds promise for advancing the utilization of geopolymer concrete as a sustainable alternative in the construction industry.

Alkali-Activated Materials Doped with ZnO: Physicomechanical and Antibacterial Properties

The requirements related to reducing the carbon footprint of cement production have directed the attention of researchers to the use of waste materials such as blast-furnace slag or fly ashes, either as a partial replacement for cement clinker or in the form of new alternative binders. This paper presents alkali-activated materials (AAMs) based on blast-furnace slag partially replaced with fly ash, metakaolin, or zeolite, activated with water glass or water glass with a small amount of water, and doped with zinc oxide. The mortars were tested for flow, hydration heat, mechanical strength, microstructure, and antimicrobial activity. The obtained test results indicate the benefits of adding water, affecting the fluidity and generating a less porous microstructure; however, the tested hydration heat, strength, and antibacterial properties are related to more favorable properties in AAMs produced on water glass alone.

Prediction Model Based on DoE and FTIR Data to Control Fast Setting and Early Shrinkage of Alkaline-Activated Slag/Silica Fume Blended Cementitious Material

This study aims to develop a material-saving performance prediction model for fast-hardening alkali-activated slag/silica fume blended pastes. The hydration process in the early stage and the microstructural properties after 24 h were analyzed using design of experiments (DoE). The experimental results show that the curing time and the FTIR wavenumber of the Si-O-T (T = Al, Si) bond in the band range of 900-1000 cm^-1 after 24 h can be predicted accurately. In detailed investigations, low wavenumbers from FTIR analysis were found to correlate with reduced shrinkage. The activator exerts a quadratic and not a silica modulus-related conditioned linear influence on the performance properties. Consequently, the prediction model based on FTIR measurements proved to be suitable in evaluation tests for predicting the material properties of those binders in the building chemistry sector.

Evaluation of CNTs and SiC Whiskers Effect on the Rheology and Mechanical Performance of Metakaolin-Based Geopolymers

Despite geopolymers having emerged as a more sustainable alternative to Portland cement, their rheological properties still need to be thoroughly investigated, aiming at the material's applicability. Additionally, studies that evaluated the fresh state of geopolymer composites with nanomaterials are scarce. Thus, two metakaolin-based geopolymer systems were reinforced with nanomaterials with a similar geometry: carbon nanotubes (CNT) and silicon carbide whiskers (SCW). The nanomaterials incorporation was assessed by rotational rheometry (conducted up to 110 min), isothermal calorimetry, compressive strength after 7 and 28 days, and the microstructure was investigated using X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). CNT and SCW incorporation (0.20 wt.%) did not significantly affect the yield stress and viscosity of the R2-group (based on metakaolin type 2), while increasing the rheological parameters up to 56.0% for the R1-group (based on metakaolin type 1). Both additions modified the reaction kinetics. Increments of up to 40.7% were observed in the compressive strength of geopolymer pastes with the incorporation of a SCW content of 0.2 wt.%. XRD and FTIR results suggest similar structural modifications between precursors. Nevertheless, R2 showed substantial transformations while the R1 group exhibited anhydrous material that can react over time. Overall, incorporating CNT and SCW contributed to higher mechanical increments on systems with average mechanical strength (R1) compared to systems with higher potential mechanical performance (R2).

Effect of Non-Calcined Sugarcane Bagasse Ash as an Alternative Precursor on the Properties of Alkali-Activated Pastes

BFS-MK-based alkali-activated materials are well established as an alternative for sustainable and green construction. This work aims to collaborate and encourage the use of biomass ashes, such as sugarcane bagasse ash (SCBA), as a precursor in alkali-activated materials (AAM). This ash is a rich source of aluminosilicate, which is a primary requirement for this application. In addition, this waste is still an environmental liability, especially in developing countries, and with a large volume of annual production. Thus, in this research, alkali-activated pastes (AA) were produced using sugarcane bagasse ash (SCBA), granulated blast furnace slag (BFS) and metakaolin (MK) as precursors. In addition, environmental gains were encouraged with energy savings, with no extra reburn or calcination steps in the SCBA. Thus, the precursors were characterized by laser granulometry, X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The pastes were produced by mixing the precursors with the activator, composed of a mixture of sodium hydroxide 8 mol/L and sodium silicate. Aiming to study the incorporation of SCBA, all samples have a precursor/activator ratio and a BFS/(BFS + MK) ratio constant of 0.6. The compressive strength analysis, FTIR, XRD, TGA, SEM and isothermal calorimetry analyses pointed out the occurrence of alkaline activation in all proposed samples for curing times of 7, 28 and 91 days. The sample GM0.6-BA0 (15% SCBA) achieved the highest compressive strength among the samples proposed (117.7 MPa, at 91 days), along with a good development of strength throughout the curing days. Thus, this work presents the properties of alkaline-activated pastes using SCBA as a sustainable and alternative precursor, seeking to encourage the use of raw materials and alternative waste in civil construction.