2D Li2S monolayer: A global minimum lithium sulfide sandwich

Understanding the electrochemical processes of SeS2 positive electrodes for developing high-performance non-aqueous lithium sulfur batteries

SeS2 positive electrodes are promising components for the development of high-energy, non-aqueous lithium sulfur batteries. However, the (electro)chemical and structural evolution of this class of positive electrodes is not yet fully understood. Here, we use operando physicochemical measurements to elucidate the dissolution and deposition processes in the SeS2 positive electrodes during lithium sulfur cell charge and discharge. Our analysis of real-time imaging reveals the pivotal role of Se in the SeS2 nucleation process, while S enables selective depositions. During the initial discharge, SeS2 converts into Se and S separately, with the dissolved Se acting as nucleation sites due to their lower nucleation potential. The Se effectively catalyzes the growth of S particles, resulting in improved lithium sulfur battery performance compared to cells using positive electrodes containing only Se or S as active materials. By adjusting the Se-to-S ratio, we demonstrate that a low concentration of Se enables uniform catalytic sites, promotes the homogeneous distribution of S and favours improved lithium sulfur battery performance.

In Situ Fabrication of High Ionic and Electronic Conductivity Interlayers Enabling Long-Life Garnet-Based Solid-State Lithium Batteries

Garnet-type Li6.75La3Zr1.75Ta0.25O12 (LLZTO) is a promising solid-state electrolyte (SSE) because of its fast ionic conduction and notable chemical/electrochemical stability toward the lithium (Li) metal. However, poor interface wettability and large interface resistance between LLZTO and Li anode greatly restrict its practical applications. In this work, we develop an in situ chemical conversion strategy to construct a highly conductive Li2S@C layer on the surface of LLZTO, enabling improved interfacial wettability between LLZTO and the Li anode. The Li/Li2S@C-LLZTO-Li2S@C/Li symmetric cell has a low interface impedance of 78.5 Ω cm2, much lower than the 970 Ω cm2 of a Li/LLZTO/Li cell. Moreover, the Li/Li2S@C-LLZTO-Li2S@C/Li cell exhibits a high critical current density of 1.4 mA cm-2 and an ultralong stability of 3000 h at 0.1 mA cm-2. When used in a LiFePO4 battery, the Li/Li2S@C-LLZTO/LiFePO4 battery exhibits a high initial discharge capacity of 150.8 mA h g-1 at 0.2 C without lithium storage capacity attenuation during 200 cycles. This work provides a novel and feasible strategy to address interface issues of SSEs and achieve lithium-dendrite-free solid-state batteries.

FeP2 monolayer: isoelectronic analogue of MoS2 with excellent electronic and optical properties

Two-dimensional semiconductors with suitable indirect band gaps, excellent light absorption capacity, and oxidation resistance are particularly suitable for material applications. Here based on first-principle calculations, we report that the FeP₂ monolayer, which is isoelectronic with MoS₂, has novel electronic properties and an ultra-low diffusion energy barrier of K on the surface, indicating its potential as an anode material of K-ion batteries. The calculated phonon dispersion curves, molecular dynamics, and elastic constants showed that it has high structural stability and oxidation resistance. The monolayer was a semiconductor with an indirect band gap of 0.68 eV. In addition, the FeP₂ monolayer had obvious light absorption in the infrared, visible, and ultraviolet regions, which can be widely used in optoelectronic devices. Bonding analysis showed that there were multicenter bonds inside every hexagonal ring. As the anode material of K-ion batteries, the FeP₂ monolayer had a capacity of 456.84 mA h g^-1, low diffusion energy barrier, and open-circuit voltage. All these characteristics suggest that the FeP₂ monolayer is a potential anode material for K-ion batteries, which needs to be further verified by experiments.

Introducing the 1H-Na2S monolayer as a new direct gap semiconductor with feature-rich electronic and magnetic properties

(a) Planar average potential (inset: Bader charge analysis) and (b) electronic localization function (iso-surface value: 0.85) of the Na2S monolayer.