Probability of survival of implant-supported metal ceramic and CAD/CAM resin nanoceramic crowns

Effect of different occlusal materials on peri-implant stress distribution with different osseointegration condition: A finite element analysis

AIM

Studies have not been done to evaluate the peri-implant stress exerted by materials(like PEEK and resin matrix ceramics) in different osseointegration conditions. To investigate the effect of different occlusal materials on peri-implant stress distribution with different osseointegration condition using finite element analysis.

SETTINGS AND DESIGN

Eighteen different 3D FEA models of implant fixed with abutment were created involving 6 different occlusal materials (Heat cured temporary acrylic resin (PMMA), Bis-GMA, PEEK, Lithium disilicate, Resin matrix ceramics and translucent Zirconia) and different osseointegrated conditions (50%, 75%, 100%).

MATERIALS AND METHODS

Models were subjected to loading vertically and obliquely followed by evaluation of stress distribution.

STATISTICAL ANALYSIS USED

The results of the simulation obtained were analysed in terms of Von mises, maximum principal and minimal principal stresses using descriptive stastistics.

RESULTS

PMMA (40.14 MPa on vertical loading and 66 MPa on oblique loading) resulted in the highest stresses and lithium disilicate (24 MPa on vertical loading and 52.40 MPa on oblique loading) resulted in least stresses among all the crown materials. Upon oblique loading, von Mises stress increases except for translucent zirconia and lithium disilicate (52.444 MPa on 50%, 47.733 MPa on 75%, and 43.973 MPa on 100% osseointegration). Minimal principal stress values decreased with increase in osseointegration upon oblique loading for PMMA, BisGMA, and PEEK.

CONCLUSION

Translucent zirconia and lithium disilicate offer a better stress transmission. Minimal principal stress values of PEEK and BisGMA decreased with increasing osseointegration.

In vitro analysis of durability of S-PRG filler-containing composite crowns for primary molar restoration

OBJECTIVE

To evaluate the reliability, maximum principal stress, shear stress, and crack initiation of a computer-aided design/computer-aided manufacturing (CAD/CAM) resin composite (RC) incorporating surface pre-reacted glass (S-PRG) filler for primary molar teeth.

METHODS

Mandibular primary molar crowns fabricated by experimental (EB) or commercially available CAD/CAM RCs (HC) were prepared and cemented to a resinous abutment tooth using an adhesive resin cement (Cem) or a conventional glass-ionomer cement (CX). These specimens were subjected to a single compressive test (n = 5/each) and the step-stress accelerated life testing (SSALT) (n = 12/each). Data was evaluated using Weibull analyses and reliability was calculated. Afterwards, the maximum principal stress and crack initiation point of each crown was analyzed by finite element analysis. To evaluate bonding of EB and HC to dentin, microtensile bond strength (μTBS) testing was conducted using primary molar teeth (n = 10/each).

RESULTS

There was no significant difference between the fracture loads of EB and HC for either cement (p > 0.05). The fracture loads of EB-CX and HC-CX were significantly lower than EB-Cem and HC-Cem (p < 0.05). The reliability at 600 N for EB-Cem was greater than that for EB-CX, HC-Cem, and HC-CX. The maximum principal stress concentrated on EB was lower than that on HC. The shear stress concentrated in the cement layer for EB-CX was higher than that for HC-CX. There was no significant difference among the μTBSs of EB-Cem, EB-CX, HC-Cem, and HC-CX (p > 0.05).

SIGNIFICANCE

The crowns fabricated with the experimental CAD/CAM RC incorporating S-PRG filler yielded greater fracture loads and reliability than the crowns manufactured with commercially available CAD/CAM RC regardless of the luting materials. These findings suggest that the experimental CAD/CAM RC crown may be clinically useful for the restoration of primary molars.

In Silico Finite Element Analysis of Implant-Supported CAD-CAM Resin Composite Crowns

PURPOSE

The aim of this study was to evaluate the mechanical behavior of an implant-supported crown made using computer-aided design and computer-aided manufacturing (CAD-CAM) resin composite (RC) blocks in the posterior region.

MATERIAL AND METHODS

Four commercially available CAD-CAM RC blocks were used in this study: Cerasmart 300 (CS300; GC, Tokyo, Japan), Katana Avencia P Block (KAP; Kuraray Noritake Dental, Niigata, Japan); KZR HR3 Gamma Theta (HR3; Yamakin, Osaka, Japan), and Estelite P block (ESP; Tokuyama Dental, Tokyo, Japan). Katana Zirconia STML (ST; Kuraray Noritake Dental) was used as the control group. The elastic moduli of each material were determined by a three-point bending test. After the CAD models were designed, two different loading scenarios (oblique, vertical) were created. 3D finite element analysis was conducted with the prepared models.

RESULTS

The elastic modulus of the material utilized for the implant restorations did not cause any change in the stresses transmitted to the implant or peripheral bone. An important difference was detected in the abutment-crown junction area. The minimum von Mises value at the abutment-crown interface was obtained in ST, which has the closest elastic modulus to the titanium abutment.

CONCLUSIONS

The 3D finite element model designed in this study was used to demonstrate that implant-supported crowns fabricated with four different CAD-CAM RCs showed no critical stress concentrations in the bone or implant under all loading conditions. These results suggest that CAD-CAM RC blocks could be used as an alternative material for implant-supported restorations in the posterior region in terms of stress distribution.

Mechanical Properties, Wear Resistance, and Reliability of Two CAD-CAM Resin Matrix Ceramics

Background and Objectives: There are limited data regarding the behavior of resin matrix ceramics for current CAD-CAM materials. Further studies may be beneficial and can help clinicians planning to use these materials during prosthodontic rehabilitation. The aim of this study was to evaluate and compare the flexural strength and strain distributions, filler content, wear, and reliability of two resin matrix ceramic CAD-CAM materials. Materials and Methods: Two resin matrix ceramics, Ambarino High-Class (AH) and Vita Enamic (VE), were tested for flexural strength (n = 24), wear (n = 10), and reliability (n = 18). Thermogravimetric analysis was used to determine the percentage of filler by weight, and digital image correlation (DIC) was used for strain analysis in flexural strength test. Reliability of each resin matrix ceramic was compared after accelerated lifetime testing of crowns using a two-parameter Weibull distribution. Data of flexural strength, wear, and thermogravimetry were analyzed by independent t-tests with significance level at 5%. Results: The results of DIC analysis were analyzed by a qualitative comparison between the images obtained. The materials tested showed different flexural strength (p < 0.05) and strain distributions. The filler content was the same as informed by manufacturers. No difference was observed in the wear or reliability analysis (p > 0.05). The flexural strength of material AH was superior to VE, and the strain distribution was compatible with this finding. Conclusions: The two resin matrix ceramics tested showed similar behavior in wear and reliability analysis. Both can provide safe use for dental crowns.

Influence of different combinations of CAD-CAM crown and customized abutment materials on the force absorption capacity in implant supported restorations - In vitro study

OBJECTIVES

To evaluate the force absorption capacity of implant supported restorations utilizing different CAD-CAM materials for the fabrication of crowns and customized abutments.

METHODS

80 titanium inserts were scanned to design customized abutments and crowns. The specimens were divided into four groups (n = 20/material): (Z): zirconia, (P): PEEK, (V): VITA Enamic, and (E): IPS e.max. Each group was subdivided into two subgroups according to customized abutment material: (Z) zirconia, and (P) for PEEK. For the assessment of force absorption, all specimens were loaded in a universal testing machine, applied loads curves were collected from the machine's software, and resulting loads curves were collected from forcemeter below the assembly. The slopes of all curves were analyzed using Two-way multivariate analysis of variance with pairwise comparisons using Tukey Post Hoc test (p < 0.05).

RESULTS

The curve progression of the applied and resulting forces varied among the investigated materials for each specimen. For zirconia abutments, ZZ showed the highest slope values of the applied and resulting force curves, followed by EZ, VZ, and PZ demonstrating statistically significant differences (P < .001). As for PEEK abutments, ZP and EP showed the least slope values, followed by PP then VP demonstrating statistically significant differences (P < .001). For Zirconia and e.max crowns, using PEEK abutments significantly increased slope loss. As for PEEK and Vita Enamic crowns changing abutment material did not significantly affect slope loss.

SIGNIFICANCE

Combining rigid crown materials with less rigid abutments might enhance their force absorption capacity. However, with less rigid crown materials a stiff substructure might be mandatory to preserve their force absorption behavior.

Effect of different tightening protocols on the probability of survival of screw-retained implant-supported crowns

PURPOSE

This study evaluated the effect of different tightening protocols on the probability of survival of screw-retained implant-supported anterior crowns.

MATERIALS AND METHODS

Seventy-two implants with internal conical connections (4.0 × 10mm, Ti-6Al-4V, Colosso, Emfils) were divided into four groups (n = 18 each): 1) Manufacturer's recommendations torque (25 N.cm for abutment's screw and 30 N.cm for crown's screw) (MaT); 2) Retightening after 10 min (ReT); 3) Torque 16% below recommended to simulate an uncalibrated wrench (AgT), and; 4) Temporary crown simulation (TeT), where crowns were torqued to 13 N.cm to simulate manual tightening, subjected to 11,200 cycles to simulate temporary crown treatment time (190 N), and then retightened to manufacturer torque (TeT). All specimens were subjected to cyclic fatigue in distilled water with a load of 190 N until 250,000 cycles or failure. The probability of survival (reliability) to complete a mission of 50,000 cycles was calculated and plotted using the Weibull 2-Parameter analysis. Weibull modulus and number of cycles at which 62.3% of the specimens would fail were also calculated and plotted. The failure mode was characterized in stereo and scanning electron microscopes (SEM).

RESULTS

The probability of survival was 69.3% for MaT, 70% for ReT, 54.8% for AgT, and 40.3% for TeT, all with no statistically significant difference. Weibull modulus was approximately 1.0 for all groups. The characteristic number of cycles for failure was 105,000 cycles for MaT, 123,000 for ReT, 82,000 cycles for AgT, and 54,900 cycles for TeT, with no significant difference between groups. The chief failure mode for MaT, ReT, AgT groups was crown screw fracture, whereas abutment screw fracture was the chief failure mode for the TeT group.

CONCLUSION

Tightening protocol did not influence the probability of survival of the screw-retained anterior crowns supported by internal conical implants (Ti-6Al-4V, Colosso, Emfils).

Survival rates of ultra-short (<6 mm) compared with short locking-taper implants supporting single crowns in posterior areas: A 5-year retrospective study

Background

Short and ultra‐short implants represent a predictable treatment, in terms of implant survival, with patients presenting insufficient available bone volumes. Moreover, single crown restorations represent a gold standard in terms of oral hygiene.

Purpose

The aim of this retrospective study was to evaluate implant survival, marginal bone loss, and peri‐implant complications in 333 locking‐taper short and ultra‐short implants.

Materials and Methods

Implants were placed in the maxillary and mandibular posterior regions of 142 patients. Clinical and radiographic examinations were performed at 5‐year recall appointments.

Results

All implants placed consisted of 8.0‐, 6.0‐, and 5.0‐mm length, 38.14%, 34.53%, and 27.33%, respectively. Three hundred thirty‐two implants (one early failure) were rehabilitated with single crowns in 141 patients. In 45.48% of the implants the crown‐to‐implant ratio was ≥2, with a mean value of 1.94. Overall implant‐based survival after 5 years of follow‐up was 96.10%: 96.85%, 95.65%, and 95.60% for 8.0‐, 6.0‐, and 5.0‐mm length implants, respectively (p = 0.82). Overall patient‐based survival was 91.55%. Regarding crestal bone level variations, average crestal bone loss and apical shift of the “first bone‐to‐implant contact point” position were 0.69 and 0.01 mm, respectively. Setting the threshold for excessive bone loss at 1 mm, during the time interval from loading to follow‐up, 28 implants experienced loss of supporting bone greater than 1 mm: 19 of them (67.85%) were surgically treated with a codified surgical regenerative protocol. After 60 months, a peri‐implantitis prevalence of 5.94% was reported, with an overall implant success of 94.06%: 95.93%, 92.73%, and 93.10% for 8.0‐, 6.0‐, and 5.0‐mm length implants, respectively (p = 0.55).

Conclusion

Long‐term outcomes suggest that short and ultra‐short locking‐taper implants can be successfully restored with single crowns in the posterior area of the maxilla and mandible.

Performance of crowns cemented on a fiber-reinforced composite framework 5-unit implant-supported prostheses: in silico and fatigue analyses

OBJECTIVE

To characterize the biomechanical performance of fiber-reinforced composite 5-unit implant-supported fixed dental prostheses (FDPs) receiving individually milled crowns by insilico and fatigue analyses.

METHODS

Eighteen implant-supported five-unit fiber-reinforced composite frameworks with an individually prepared abutment design were fabricated, and ninety resin-matrix ceramic crowns were milled to fit each abutment. FDPs were subjected to step-stress accelerated-life testing with load delivered at the center of the pontic and at 2nd molar and 1st premolar until failure. The reliability of the prostheses combining all loaded data and of each loaded tooth was estimated for a mission of 50,000 cycles at 300, 600 and 900 N. Weibull parameters were calculated and plotted. Fractographic and finite element analysis were performed.

RESULTS

Fatigue analysis demonstrated high probability of survival at 300 N, with no significant differences when the set load was increased to 600 and 900 N. 1st and 2nd molar dataset showed high reliability at 300 N, which remained high for the higher load missions; whereas 1st premolar dataset showed a significant decrease when the reliability at 300 N was compared to higher load missions. The characteristic-strength of the combined dataset was 1252 N, with 1st molar dataset presenting higher values relative to 2nd molar and 1st premolar, both significantly different. Failure modes comprised chiefly cohesive fracture within the crown material originated from cracks at the occlusal area, matching the maximum principal strain location.

SIGNIFICANCE

Five-unit implant-supported FDP with crowns individually cemented in a fiber-reinforced composite framework presented a high survival probability. Crown fracture comprised the main failure mode.

In vitro evaluation of material dependent force damping behavior of implant-supported restorations using different CAD-CAM materials and luting conditions

STATEMENT OF PROBLEM

Although force-damping behavior that matches natural teeth may be unobtainable, an optimal combination of crown material and luting agent might have a beneficial effect on the force absorption capacity of implant-supported restorations. However, the force-absorbing behavior of various restorative materials has not yet been satisfactorily investigated.

PURPOSE

The purpose of this in vitro study was to evaluate the material dependent force-damping behavior of implant-supported crowns fabricated from different computer-aided design and computer-aided manufacturing (CAD-CAM) materials luted to implant abutments under different conditions.

MATERIAL AND METHODS

Titanium inserts (N=84) were screwed to implant analogs, scanned to design zirconia abutments, and divided into 4 groups to receive CAD-CAM fabricated crowns in 4 materials: zirconia, polyetheretherketone (PEEK), polymer-infiltrated ceramics (VITA ENAMIC), and lithium disilicate (e.max). The crowns were subdivided as per the luting agent: none, interim cement, and adhesive resin cement. Measurements were performed by loading specimens in a universal testing machine with an increasing force and measuring the resulting force with a digital forcemeter, followed by image processing and data acquisition. Two-way multivariate analysis of variance (MANOVA) was used to assess all interactions with multiple pairwise comparisons (α=.05).

RESULTS

The curve progression of the applied and resulting forces varied significantly among the investigated materials, resulting in differently inclined slopes for each material (P<.001). With no cementation, the mean slope values of the resulting force curves ranged from 77.5 ±0.03 degrees for zirconia, followed by 71.8 ±0.03 degrees for lithium disilicate, 56.2 ±0.1 degrees for polymer-infiltrated ceramics, and 51.1 ±0.01 degrees for polyetheretherketone. With interim cementation, the mean slope values ranged from 75.4 ±0.01 degrees for zirconia, followed by 70.05 ±0.02 degrees for lithium disilicate, 56.1 ±0.02 degrees for polymer-infiltrated ceramics, and 52.2 ±0.1 degrees for polyetheretherketone. As with adhesive cementation, curve slopes ranged from 73.2 ±0.02 degrees for zirconia, followed by 70.5 ±0.2 degrees for lithium disilicate, 55.9 ±0.04 degrees for polymer-infiltrated ceramics, and 52.3 ±0.1 degrees for polyetheretherketone. Slope loss was significant after the cementation of zirconia and lithium disilicate crowns but less significant for polymer-infiltrated ceramics and polyetheretherketone.

CONCLUSIONS

Force damping is generally material dependent, yet implant-supported crowns fabricated from resilient materials such as polymer-infiltrated ceramics and PEEK show better force absorption than rigid materials such as zirconia and lithium disilicate ceramics. Furthermore, cementation of rigid materials significantly increased slope loss, indicating enhancement in their force-damping behavior, whereas less-rigid materials benefit less from cementation. Further studies are essential to investigate the effect of prosthetic materials on the stress distribution to the peri-implant bone in the crown-abutment-implant complex.

Survival of implant-supported resin-matrix ceramic crowns: In silico and fatigue analyses

OBJECTIVE

To evaluate the fatigue survival, failure mode, and maximum principal stress (MP Stress) and strain (MP Strain) of resin-matrix ceramic systems used for implant-supported crowns.

METHODS

Identical molar crowns were milled using four resin-matrix ceramics (n = 21/material): (i) Shofu Hard, (ii) Cerasmart (iii) Enamic, and (iv) Shofu HC. Crowns were cemented on the abutments, and the assembly underwent step-stress accelerated-life testing. Use level probability Weibull curves at 300 N were plotted and the reliability at 300, 500 and 800 N was calculated for a mission of 50,000 cycles. Fractographic analysis was performed using stereomicroscope and scanning electron microscope. MP Stress and MP Strain were determined by finite element analysis.

RESULTS

While fatigue dictated failures for Cerasmart (β > 1), material strength controlled Shofu Hard, Enamic, and Shofu HC failures (β < 1). Shofu HC presented lower reliability at 300 N (79%) and 500 N (59%) than other systems (>90%), statistically different at 500 N. Enamic (57%) exhibited a significant reduction in the probability of survival at 800 N, significantly lower than Shofu Hard and Cerasmart; however, higher than Shofu HC (12%). Shofu Hard and Cerasmart (>93%) demonstrated no significant difference for any calculated mission (300-800 N). Failure mode predominantly involved resin-matrix ceramic fracture originated from occlusal cracks, corroborating with the MP Stress and Strain location, propagating through the proximal and cervical margins.

SIGNIFICANCE

All resin-matrix ceramics crowns demonstrated high probability of survival in a physiological molar load, whereas Shofu Hard and Cerasmart outperformed Enamic and Shofu HC at higher loads. Material fracture comprised the main failure mode.

Resin-matrix ceramics for occlusal veneers: Effect of thickness on reliability and stress distribution

OBJECTIVE

To evaluate the influence of resin-matrix ceramic material and thickness on reliability and stress distribution of occlusal veneers (OV).

METHODS

One hundred and twenty-six OV of a mandibular first molar were milled using a CAD/CAM system and allocated according to materials (resin nanoceramic (RNC) or polymer-infiltrated ceramic network (PICN)) and thicknesses (0.5, 1.0 and 1.5 mm), totaling six groups (RNC0.5, RNC1, RNC1.5, PICN0.5, PICN1, and PICN1.5). Step-stress accelerated-life testing was performed (n = 21/group) with the load applied at the distobuccal cusp tip of the occlusal veneer until failure or suspension. The use level probability Weibull curves and reliability were calculated and plotted (90% CI). Finite element analysis evaluated the stress distribution according to maximum principal stress (σ_max) on the restoration and maximum shear stress (τ_max) on the cement layer.

RESULTS

There was no difference in the probability of survival for the estimated missions among the groups, except at 600 N in which the results were significantly lower to PICN1.5 (6%) compared to RNC1 (55%) and RNC1.5 (60%). The σ_max values were higher for PICN (31.85-48.63 MPa) than RNC (30.78-33.09 MPa) in the same thicknesses. In addition, 0.5 mm groups concentrated more stress in the restoration (33.09-48.63 MPa) than 1.0 mm (31.11-35.36 MPa) and 1.5 mm (30.78-31.85 MPa) groups in the same material.

SIGNIFICANCE

Both resin-matrix ceramic materials seem up-and-coming restorative systems for occlusal veneers irrespective of the thicknesses as a consequence of the high reliability.

Comparison of CAD/CAM manufactured implant-supported crowns with different analyses

Background

Present study compared the failure load of CAD/CAM-manufactured implant-supported crowns and the stress distribution on the prosthesis-implant-bone complex with different restoration techniques.

Methods

The materials were divided into four groups: group L-M: lithium disilicate ceramic (LDS, monolithic), group L-V: LDS ceramic (veneering), group ZL-M: zirconia-reinforced lithium silicate ceramic (ZLS, monolithic), group ZL-V: ZLS ceramic (veneering). Crown restorations were subjected to load-to-failure test (0.5 mm/min). Failure loads of each group were statistically analyzed (two-way ANOVA, post hoc Tukey HSD, α = 0.05). Finite element analysis (FEA) was used to compare the stress distribution of crown restorations.

Results

Group L-M had the highest failure load (2891.88 ± 410.12 N) with a significant difference from other groups (p < 0.05). Although there was a significant difference between group ZL-M (1750.28 ± 314.96 N) and ZL-V (2202.55 ± 503.14 N), there was no significant difference from group L-V in both groups (2077.37 ± 356.59 N) (p > 0.05).

Conclusions

The veneer application had opposite effects on ceramics, increased the failure load of ZLS and reduced it for LDS without a statistically significant difference. Both materials are suitable for implant-supported crowns. Different restorative materials did not influence the stress distribution, but monolithic restorations reduced the stress concentration on the implant and bone.

Survival of Short and Ultra-Short Locking-Taper Implants Supporting Single Crowns in the Posterior Mandible: A 3-Year Retrospective Study

The purpose of this retrospective study was to determine survival and peri-implant marginal bone loss of short and ultra-short implants placed in the posterior mandible. A total of 98 patients received 201 locking-taper implants between January 2014 and January 2015. Implants were placed with a 2-stage approach and restored with single crowns. Clinical and radiographic examinations were performed at 3-year recall appointments. At that time, the proportion of implant survival by length, and variations of crestal bone levels (mean crestal bone loss and mean apical shift of the "first bone-to-implant contact point" position) were assessed. Significance level was set at 0.05. The total number of implants examined 36 months after loading included: 71 implants, 8.0 mm in length; 82 implants, 6.0 mm in length; and 48 implants, 5.0 mm in length. Five implants failed. The overall proportion of survival was 97.51%, with 98.59% for the 8.0-mm implants, 97.56% for the 6.0-mm implants, and 95.83% for the 5.0-mm implants. No statistically significant differences were found among the groups regarding implant survival (P = .73), mean crestal bone loss (P = .31), or mean apical shift of the "first bone-to-implant contact point" position (P = .36). Single-crown short and ultra-short implants may offer predictable outcomes in the atrophic posterior mandibular regions, though further investigations with longer follow-up evaluations are necessary to validate our results.

Survival Probability, Weibull Characteristics, Stress Distribution, and Fractographic Analysis of Polymer-Infiltrated Ceramic Network Restorations Cemented on a Chairside Titanium Base: An In Vitro and In Silico Study

Different techniques are available to manufacture polymer-infiltrated ceramic restorations cemented on a chairside titanium base. To compare the influence of these techniques in the mechanical response, 75 implant-supported crowns were divided in three groups: CME (crown cemented on a mesostructure), a two-piece prosthetic solution consisting of a crown and hybrid abutment; MC (monolithic crown), a one-piece prosthetic solution consisting of a crown; and MP (monolithic crown with perforation), a one-piece prosthetic solution consisting of a crown with a screw access hole. All specimens were stepwise fatigued (50 N in each 20,000 cycles until 1200 N and 350,000 cycles). The failed crowns were inspected under scanning electron microscopy. The finite element method was applied to analyze mechanical behavior under 300 N axial load. Log-Rank (p = 0.17) and Wilcoxon (p = 0.11) tests revealed similar survival probability at 300 and 900 N. Higher stress concentration was observed in the crowns’ emergence profiles. The MP and CME techniques showed similar survival and can be applied to manufacture an implant-supported crown. In all groups, the stress concentration associated with fractographic analysis suggests that the region of the emergence profile should always be evaluated due to the high prevalence of failures in this area.

Effect of surface treatments and universal adhesive application on the microshear bond strength of CAD/CAM materials

PURPOSE

The aim of this study was to evaluate the microshear bond strength (µSBS) of four computer-aided design/computer-aided manufacturing (CAD/CAM) blocks repaired with composite resin using three different surface treatment protocols.

MATERIALS AND METHODS

Four different CAD/CAM blocks were used in this study: (1) flexible hybrid ceramic (FHC), (2) resin nanoceramic (RNC), (c) polymer infiltrated ceramic network (PICN) and (4) feldspar ceramic (FC). All groups were further divided into four subgroups according to surface treatment: control, hydrofluoric acid etching (HF), air-borne particle abrasion with aluminum oxide (AlO), and tribochemical silica coating (TSC). After surface treatments, silane was applied to half of the specimens. Then, a silane-containing universal adhesive was applied, and specimens were repaired with a composite, Next, μSBS test was performed. Additional specimens were examined with a contact profilometer and scanning electron microscopy. The data were analyzed with ANOVA and Tukey tests.

RESULTS

The findings revealed that silane application yielded higher µSBS values (P<.05). All surface treatments were showed a significant increase in µSBS values compared to the control (P<.05). For FHC and RNC, the most influential treatments were AlO and TSC (P<.05).

CONCLUSION

Surface treatment is mandatory when the silane is not preferred, but the best bond strength values were obtained with the combination of surface treatment and silane application. HF provides improved bond strength when the ceramic content of material increases, whereas AlO and TSC gives improved bond strength when the composite content of material increases.

Fatigue survival and damage modes of lithium disilicate and resin nanoceramic crowns

Polymer-based composite materials have been proposed as an alternative for single unit restorations, due to their resilient and shock absorbing behavior, in contrast to the brittleness of ceramic materials that could result in failure by fracture.

Influence of Manufacturing Methods of Implant-Supported Crowns on External and Internal Marginal Fit: A Micro-CT Analysis

Aim

To evaluate the influence of different manufacturing methods of single implant-supported metallic crowns on the internal and external marginal fit through computed microtomography.

Methods

Forty external hexagon implants were divided into 4 groups (n = 8), according to the manufacturing method: GC, conventional casting; GI, induction casting; GP, plasma casting; and GCAD, CAD/CAM machining. The crowns were attached to the implants with insertion torque of 30 N·cm. The external (vertical and horizontal) marginal fit and internal fit were assessed through computed microtomography. Internal and external marginal fit data (μm) were submitted to a one-way ANOVA and Tukey's test (α = .05). Qualitative evaluation of the images was conducted by using micro-CT.

Results

The statistical analysis revealed no significant difference between the groups for vertical misfit (P = 0.721). There was no significant difference (P > 0.05) for the internal and horizontal marginal misfit in the groups GC, GI, and GP, but it was found for the group GCAD (P ≤ 0.05). Qualitative analysis revealed that most of the samples of cast groups exhibited crowns underextension while the group GCAD showed overextension.

Conclusions

The manufacturing method of the crowns influenced the accuracy of marginal fit between the prosthesis and implant. The best results were found for the crowns fabricated through CAD/CAM machining.

Influence of different surface treatments on bond strength of novel CAD/CAM restorative materials to resin cement

PURPOSE

To evaluate the effects of different surface treatments on the bond strength of novel CAD/CAM restorative materials to resin cement by four point bending test.

MATERIALS AND METHODS

The CAD/CAM materials under investigation were e.max CAD, Mark II, Lava Ultimate, and Enamic. A total of 400 bar specimens (4×1.2×12 mm) (n=10) milled from the CAD/CAM blocks underwent various pretreatments (no pretreatment (C), hydrofluoric acid (A), hydrofluoric acid + universal adhesive (Scotchbond) (AS), sandblasting (Sb), and sandblasting + universal adhesive (SbS)). The bars were luted end-to-end on the prepared surfaces with a dual curing adhesive resin cement (Variolink N, Ivoclar Vivadent) on the custom-made stainless steel mold. Ten test specimens for each treatment and material combination were performed with four point bending test method. Data were analyzed using ANOVA and Tukey's test.

RESULTS

The surface treatment and type of CAD/CAM restorative material showed a significant effect on the four point bending strength (FPBS) (P<.001). For LDC, AS surface treatment showed the highest FPBS results (100.31 ± 10.7 MPa) and the lowest values were obtained in RNC (23.63 ± 9.0 MPa) for control group. SEM analyses showed that the surface topography of CAD/CAM restorative materials was modified after treatments.

CONCLUSION

The surface treatment of sandblasting or HF acid etching in combination with a universal adhesive containing MDP can be suggested for the adhesive cementation of the novel CAD/CAM restorative materials.

Fracture behavior, marginal gap width, and marginal quality of vented or pre-cemented CAD/CAM all-ceramic crowns luted on Y-TZP implants

OBJECTIVES

To investigate the fracture behavior and marginal gap region of CAD/CAM fabricated lithium disilicate (L) and zirconium dioxide (Z) crowns using palatal venting (PV), pre-cementation with custom analogs (CA), or conventional cementation technique (SP) with adhesive cement (A) or resin-modified glass ionomer cement (B).

MATERIAL AND METHODS

Twelve groups (n = 6) were set according to material (L, Z), cement (A, B), and technique (PV, CA, SP). Specimens were thermo-mechanical aged (TML), loaded until fracture (LF) and fracture patterns recorded. Marginal gap width and quality were assessed and compared to replicas obtained before and after TML.

RESULTS

Crown material significantly influenced LF with a mean of 1037.6 ± 282.4 N in L and 5356.3 ± 1207.0 N in Z groups (p < .001). Neither cement material nor cementation method affected the outcome. Fractures occurred along the mesial-distal central fissure in both materials. Gap width before TML was 22.04 ± 13.42 μm for L and 19.98 ± 12.72 μm for Z specimens, with overall no influence of crown material, cement type, or method. Marginal cleanliness just below the polished implant shoulder reached 66.7%-88.9% with A, and 91.7%-100% with B, and tended to increase in all groups during TML indicating a decrease in excess cement. Implant-crown junctions were cleaner with B compared to A (p ≤ .001) and along Z crown surfaces compared to L (p ≤ .007).

CONCLUSIONS

Crown venting of lithium disilicate and zirconium dioxide crowns did not affect the fracture load and patterns. Complete cement removal was rare, and the observed particle ablation requires further clinical attention, particularly with submucosal margins.

A Critical Perspective on Mechanical Testing of Implants and Prostheses

The degree of interplay among variables in dental implant treatment presents a challenge to randomized clinical trials attempting to answer questions in a timely, unbiased, and economically feasible fashion. Further adding complexity to the different scenarios is the varied implant designs and related bone response, area of implantation, implant bulk material, restoration, abutments and related screws, fixation mode (screwed, fixed, or a combination), and horizontal implant-abutment matching geometry. This article critically appraises the most common mechanical testing methods used to characterize the implant-prostheses complex. It attempts to provide insight into the process of construction of an informed database of clinically relevant questions regarding preclinical evaluation of implant biomechanics and failure mechanisms. The use of single load to failure, fatigue life, fatigue limit, and step-stress accelerated life testing is discussed with emphasis on their deliverables, weaknesses, and strengths. Fractographic analysis and challenges in the correlation between laboratory- and in-service-produced failures of dental ceramics, resin composites, and titanium are introduced. In addition, examples are presented of mechanical characterization studies used in our laboratory to assess some implant-supported rehabilitation variables.