Development of viscoelastic stability of resin-composites incorporating novel matrices

Nanoindentation creep: The impact of water and artificial saliva storage on milled and 3D-printed resin composites

PURPOSE

This study evaluated the effects of artificial saliva and distilled water on the nanoindentation creep of different 3D-printed and milled CAD-CAM resin composites.

MATERIAL AND METHODS

Disk-shaped specimens were subtractively fabricated from polymer-infiltrated ceramic network (EN) and reinforced resin composite (B) and additively from resin composite (C) and hybrid resin composite (VS) using digital light processing (DLP). Specimens from each material were divided into two groups according to their storage conditions (artificial saliva or distilled water for 3 months). Creep was analyzed by nanoindentation testing. Statistical analysis was done using two-way ANOVA, one-way ANOVA, Bonferroni post hoc tests, and independent t-test (α = 0.05).

RESULTS

The main effects of material and storage conditions, and their interaction were statistically significant on nanoindentation (p < 0.001). Storage condition had the greatest influence (partial eta squared ηP 2 = 0.370), followed by the material (ηP 2 = 0.359), and the interaction (ηP 2 = 0.329). The nanoindentation creep depths after artificial saliva storage ranged from 0.34 to 0.51 µm and from 0.50 to 0.87 µm after distilled water storage. One of the additively manufactured groups had higher nanoindentation creep depths in both storage conditions.

CONCLUSIONS

All specimens showed comparable performance after artificial saliva storage, but increased nanoindentation creep after distilled water storage for 3 months. The subtractive CAD-CAM blocks showed superior dimensional stability in terms of nanoindentation creep depths in both storage conditions. Additively manufactured composite resins had lower dimensional stability than one of the subtractively manufactured composites, which was demonstrated as having higher creep deformation and maximum recovery. However, after artificial saliva storage, one of the additively manufactured resins had dimensional stability similar to that of subtractively manufactured.

The effect of water storage on nanoindentation creep of various CAD-CAM composite blocks

BACKGROUND

To study the effect of water storage (3 months) on the creep deformation of various CAD-CAM composite structures at the nanoscale and compare it to that at the macroscale.

METHODS

Seven CAD-CAM blocks were investigated: five resin-composite blocks (RCB), one polymer-infiltrated ceramic network (PICN) block, and one ceramic-filled polyetheretherketone (PEEK) block. Specimens of each material (n = 6) were separated into two groups (n = 3) according to their storage conditions (24 h dry storage at 23˚C and 3 months storage in 37˚C distilled water). Nano-indentation creep measurements were undertaken (creep depth measured in µm) using a nanoindenter (Nanovea) equipped with Berkovich three-sided pyramidal diamond tip. The machine was set for the chosen parameters: a load of 20 gf, a pause of 20 s, and the material type. Thirty indentations on 3 samples were made for each material for each test. Data were analysed using two-way ANOVA followed by one-way ANOVA and Bonferroni post hoc tests and independent t-test (< 0.05) for comparisons between the materials.

RESULTS

The nanoindentation creep depth after 24 h storage ranged from 0.09 to 0.33 μm and increased after 3 months storage in distilled water to between 0.28 and 3.46 μm. There was a statistically significant difference in nanoindentation creep behaviour between the two storage conditions for each investigated material (independent t-test) and between all materials (Bonferroni post hoc). There was a non-significant negative correlation between nanoindentation creep (µm) and filler weight% at 24 h dry storage but a significant correlation at 3 months of water storage. A further non-significant positive correlation between nanoindentation creep (µm) and bulk compressive creep (%) was found.

CONCLUSION

The PICN material showed superior dimensional stability in terms of nanoindentation creep depth in both storage conditions. Other composite blocks showed comparable performance at 24 h dry condition, but an increased nanoindentation creep upon water storage.

Antimicrobial agents in dental restorative materials: a on polymerization, short-term drug release and biological impact

With the aim to design bioactive dental restorative material, the present study investigated the influence of the antimicrobial agents chlorhexidine diacetate (CHX) and octinidine (di)hydrochloride (ODH) when incorporated in two different materials. Selected parameters were polymerization enthalpy, short-term drug release, and the effect on Streptococcus mutans as well as human gingival fibroblasts. Samples were made by mixing a nano-hybrid ormocer (O) and a methacrylate-based nano-hybrid composite (C), each with a mass fraction of 2% CHX or ODH. Release profiles and concentrations of active agents from the resins were assessed, and the cell proliferation of human gingival fibroblasts as well as Streptococcus mutans cultured with the eluates were evaluated. The influence on polymerization was assessed by means of differential scanning calorimetry. Both drugs, especially ODH, showed a decreasing effect on polymerization enthalpies associated with a lowered crosslinking degree. At the same time ODH appeared to be released more persistently than CHX. Moreover, ODH was more efficient with regard to bacteria growth inhibition but also more cytotoxic in terms of reduction of cell viability. ODH is deemed more appropriate for application in a dental resin-based drug delivery system, because of the more persistent drug release than seen for CHX.

Recent update on potential cytotoxicity, biocompatibility and preventive measures of biomaterials used in dentistry

Dental treatment is provided for a wide variety of oral health problems like dental caries, periodontal diseases, periapical infections, replacement of missing teeth and orthodontic problems. Various biomaterials, like composite resins, amalgam, glass ionomer cement, acrylic resins, metal alloys, impression materials, bone grafts, membranes, local anaesthetics, etc., are used for dental applications. The physical and chemical characteristics of these materials influence the outcome of dental treatment. It also impacts on the biological, allergic and toxic potential of biomaterials. With innovations in science and their positive results, there is also a need for awareness about the biological risks of these biomaterials. The aim of dental treatment is to have effective, yet safe, and long-lasting results for the benefit of patients. For this, it is important to have a thorough understanding of biomaterials and their effects on local and systemic health. Materials used in dentistry undergo a series of analyses before their oral applications. To the best of our knowledge, this is the first and original review that discusses the reasons for and studies on the toxicity of commonly used biomaterials for applications in dentistry. It will help clinicians to formulate a methodical approach for the selection of dental biomaterials, thus providing an awareness for forecasting their risk of toxic reactions.

Characterizing surface viscoelastic integrity of ultra-fast photo-polymerized composites: Methods development

OBJECTIVE

Resin-Composites are now available designed for polymerization using 3 s of intense light irradiation. The aim was to develop an experimental method to probe their surface viscoelastic integrity immediately following such rapid photo-cure via macroscopic surface indentation under constant stress as a function of time.

METHODS

Two bulk-fill composites (Ivoclar AG) were studied: Tetric PowerFill (PFill) and PowerFlow (PFlow). Split molds were used to fabricate cylindrical {4 mm (dia) × 4 mm} paste specimens, irradiated at 23 °C at 0 mm from the top surface with a BluephasePowerCure LED-LCU, with 3 s or 5 s modes, emitting 3 and 2 W/cm², respectively. Post-irradiation specimens were immediately transferred to an apparatus equipped with a flat-ended indentor of 1.5 mm diameter. 14 MPa compressive stress at the indentor tip was applied centrally in < 2 min and maintained constant for 2 h. Indentation (I) magnitudes were recorded in real-time (t), with I(t) data re-expressed as % indentation relative to the 4 mm specimen height. After 2 h, the indentor was unloaded and indentation recovery was monitored for a further 2 h. Parallel sets of measurements were made where indentation was delayed for 24 h. Further measurements were made with more conventional composites: EvoCeram Bulk Fill (ECeram) and Tetric EvoFlow Bulk Fill (EFlow). These were irradiated for 20 s at 1.2 W/cm². Kinetic data were curve-fitted to exponential growth functions and key parameters analyzed by ANOVA and post-hoc tests (α = 0.05).

RESULTS

I(t) plots looked initially similar to bulk creep/recovery: rapid deformation plus viscoelastic response; then, upon unloading: rapid (elastic) recovery followed by partial viscoelastic recovery. However, unlike multiply irradiated and stored bulk-creep specimens, the present specimens were exposed to only 3 or 5 s "occlusal" irradiation; generating "hard" surfaces. Subsequently, during the 2 h indentation, the polymer matrix network continued to harden and consolidate. Upon initial loading, I(t) reached 2-3% indentation, depending upon the formulation. Upon unloading at 2 h, elastic recovery was only ca. 1 %. Delayed loading for 24 h, generated I(t) plots of significantly reduced magnitude. Most importantly, however, the I(t) plots for ECeram and EFlow, after 20 s irradiation, showed I(t) magnitudes quite comparable to the PFill and PFlow rapid-cure composites.

SIGNIFICANCE

Macroscopic indentation creep has been shown to be a workable procedure that can be applied to rapid-cure materials to assess their immediate surface integrity and developing viscoelastic characteristics. The applied stress of 14 MPa was relatively severe and the indentation/recovery profiles of PowerFill materials with only 3 or 5 s irradiation demonstrated comparability with their established 20 s cure siblings, evidencing the suitability of the PowerCure system for clinical application.

Cytotoxicity of Different Nano Composite Resins on Human Gingival and Periodontal Ligament Fibroblast Cell Lines: An In Vitro Study

The aim of this study is to determine the cytotoxicity of three different nano composite resins (CRs) on human gingival fibroblast (hGF) and periodontal ligament fibroblast (hPDLF) cell lines. These CRs selected were nanohybrid organic monomer-based Admira Fusion (AF), nanohybrid Bis-(acryloyloxymethyl) tricyclo [5.2.1.0.sup.2,6] decane-based Charisma Topaz (CT), and supra nano filled resin-based Estelite Quick Sigma (EQS). MTT assay was performed to assess the cytotoxicity of CRs at 24 h and one week. AF and EQS applied on hGF cells at 24 h and one week demonstrated similar cytotoxic outcomes. Cytotoxicity of CT on hGF cells at one week was higher than 24 h (p = 0.04). Cytotoxicity of CT on hGF cells was higher at 24 h (p = 0.002) and one week (p = 0.009) compared to control. All composites showed higher cytotoxicity on hPDLF cells at one week than the 24 h (AF; p = 0.02, CT; p = 0.02, EQS; p = 0.04). AF and EQS demonstrated lower cytotoxicity on hPDLF cells than the control group at 24 h (AF; p = 0.01, EQS; p = 0.001). CT was found more cytotoxic on hPDLF cells than the control (p = 0.01) and EQS group (p = 0.008) at one week. The cytotoxicity of CRs on hGF and hPDLF cells vary, according to the type of composites, cell types, and exposure time.

Viscoelastic stability of pre-cured resin-composite CAD/CAM structures

OBJECTIVES

To study the effect of water storage (3 months) on the creep deformation and recovery of CAD/CAM composite materials to determine their viscoelastic stability.

MATERIALS AND METHODS

Five CAD/CAM composite blocks, with increasing filler loading, and one polymer-infiltrated ceramic network (PICN) were studied. Six specimens of each material were separated into two groups (n=3) according to their storage conditions (24 h dry storage at 23°C versus 3 months storage in 37°C distilled water). A constant static compressive stress of 20 MPa was applied on each specimen via a loading pin for 2 h followed by unloading and monitoring strain recovery for a further period of 2 h. The maximum creep-strain (%) and permanent set (%) were recorded. Data were analysed via two-way ANOVA followed by one-way ANOVA and Bonferroni post hoc tests (<0.05) for comparisons between the materials. Homogeneity of variance was calculated via Levene's statistics.

RESULTS

The maximum creep strain after 24 h dry ranged from 0.45% to 1.09% and increased after 3-month storage in distilled water to between 0.71% and 1.85%. The permanent set after 24 h dry storage ranged from 0.033% to 0.15% and increased after 3-month water storage to between 0.087% and 0.18%. The maximum creep strain also reduced with increasing filler loading.

SIGNIFICANCE

The PICN material exhibited superior dimensional stability to all of the pre-cured resin composite blocks in both storage conditions with deformation being predominantly elastic rather than viscoelastic. Notwithstanding, two of the resin-matrix composite blocks approached the PICN performance, when dry, but less so after water storage.

Simultaneous Evaluation of Creep Deformation and Recovery of Bulk-Fill Dental Composites Immersed in Food-Simulating Liquids

The aim of this study is to compare the creep/recovery behavior of bulk-fill dental composites after storage in various food simulating organic solvents. For this purpose, five different resin-composites (four bulk-fills and one conventional) were used. A total of 20 rectangular specimens (14 mm &times; 3 mm &times; 0.7 mm) were prepared by filling the resin-composites in Teflon mold. All of the specimens for each material (n = 5) were divided into four groups namely dry (control), distilled water (DW), artificial saliva, and absolute ethanol. The specimens were subjected to three-point bending creep test during immersion directly. A constant load of 2 N was used for each specimen with loading and unloading time 2 h each.

RESULTS

SF2 and XF showed a lower creep strain % after immersion, ranging from 0.44 (dry) to 0.75 (saliva) and 0.43 (dry) to 0.80 (ethanol), respectively. TNC BF depicts the maximum creep strain % ranging from 1.24% (dry) to 2.87% (ethanol) followed by FBF ranging from 1.17 (dry) to 2.59 (ethanol). However, the conventional material (GR) showed lower creep strain after immersion ranging from 0.28 to 0.54. Moreover, SF2 resulted in the highest creep recovery in all of the composites groups, as well as conventional material. The other composite groups showed lower creep recovery as compared to the conventional material (GR). The creep strain % for all the bulk-fill composites materials were increased during immersion in the liquids. However, for the conventional material, the creep deformation is decreased after immersion. SF2 showed the highest percentage of creep recovery among the bulk-fill composites, followed by XF.