Synthesis and characterization of Ciprofloxacin-containing divinyl oligomers and assessment of their biodegradation in simulated salivary esterase

Biodegradation of Dental Resin-Based Composite—A Potential Factor Affecting the Bonding Effect: A Narrative Review

In recent years, although resin composite has played an important role in the restoration of tooth defects, it still has several disadvantages, including being biodegraded by saliva, bacteria and other enzymes in the oral cavity, which may result in repair failure. This factor is not conducive to the long-term survival of the prosthesis in the mouth. In this article, we review the causes, influencing factors and prevention methods of resin biodegradation. Biodegradation is mainly caused by esterase in saliva and bacteria, which breaks the ester bond in resin and causes the release of monomers. The mechanical properties of the prosthesis can then be affected. Meanwhile, cathepsin and MMPs are activated on the bonding surface, which may decompose the dentin collagen. In addition, neutrophils and residual water on the bonding surface can also aggravate biodegradation. Currently, the primary methods to prevent biodegradation involve adding antibacterial agents to resin, inhibiting the activity of MMPs and enhancing the crosslinking of collagen fibers. All of the above indicates that in the preparation and adhesion of resin materials, attention should be paid to the influence of biodegradation to improve the prosthesis’s service life in the complex environment of the oral cavity.

Methacrylation of epigallocatechin-gallate for covalent attachment with a dental polymer

OBJECTIVE

Synthesize novel epigallocatechin-gallate (EGCG) methacrylate monomers with the ability to copolymerize with dental methacrylate resins.

METHODS

EGCG was reacted with 1/3 (E33), 2/3 (E67) and 1 (E100) molar equivalents of methacyloyl chloride introducing three degrees of polymerizablility. EGCG-methacrylates were characterized by Fourier Transform Infrared Spectroscopy (FTIR) and Nuclear Magnetic Resonance (NMR). E33, E67, E100 and neat EGCG were incorporated into TEGDMA at 0.5-20% ratios (m/m). Copolymers were tested for degree of conversion (%DC), EGCG release, gel content (%GC), degree of swelling (%DS), flexural properties and bacterial viability (Streptococcus mutans, baseline/30-days). Neat TEGDMA and TEGDMA passively loaded with EGCG (E0) were used as controls. Data were analysed by one-way ANOVA, Tukey, and Dunnett's method (α=5%). Two-way ANOVA and Bonferroni were used to investigate factor interaction.

RESULTS

FTIR/NMR confirmed synthesis of desired compounds. All of E100 incorporated ratios had %DC similar to TEGDMA. Remaining groups had reduction in %DC at 2% in E0, 10% in E33 and 20% in E67 ratios. EGCG was stable within ECGC-methacrylate copolymers. Release of EGCG from E0 significantly increased with higher EGCG ratios. Except for E100, higher EGCG or EGCG-methacrylate ratios led to decreased %CG and %DS. At baseline, E0 had the lowest bacterial survival rates (1-10% survival) at all ratios compared to E33, E67, E100, and neat TEGDMA. However, E33, E67 and E100 still had statistically lower survival rates (7-53%) compared with neat TEGDMA. After 30-days, all compounds had similar survival rates for all ratios, which were lower than that of neat TEGDMA.

SIGNIFICANCE

Demonstration of methacrylate functionalized EGCG- with inherited antibacterial activity for improved restoration longevity.

Recent Progress in Antimicrobial Strategies for Resin-Based Restoratives

Repairing tooth defects with dental resin composites is currently the most commonly used method due to their tooth-colored esthetics and photocuring properties. However, the higher than desirable failure rate and moderate service life are the biggest challenges the composites currently face. Secondary caries is one of the most common reasons leading to repair failure. Therefore, many attempts have been carried out on the development of a new generation of antimicrobial and therapeutic dental polymer composite materials to inhibit dental caries and prolong the lifespan of restorations. These new antimicrobial materials can inhibit the formation of biofilms, reduce acid production from bacteria and the occurrence of secondary caries. These results are encouraging and open the doors to future clinical studies on the therapeutic value of antimicrobial dental resin-based restoratives. However, antimicrobial resins still face challenges such as biocompatibility, drug resistance and uncontrolled release of antimicrobial agents. In the future, we should focus on the development of more efficient, durable and smart antimicrobial dental resins. This article focuses on the most recent 5 years of research, reviews the current antimicrobial strategies of composite resins, and introduces representative antimicrobial agents and their antimicrobial mechanisms.

Synthesis and antibacterial activity of polymer-antibiotic conjugates incorporated into a resin-based dental adhesive

This work reports on polymer-antibiotic conjugates (PACs) as additives to resin-based restorative dental materials as a new strategy to convey sustained antibacterial character to these materials. Such antibacterial performance is expected to improve their longevity in the oral cavity. Using the previously reported ciprofloxacin (Cip)-based PAC as a control, a penicillin V (PV)-based PAC was investigated. The monomer-antibiotic conjugate (MAC) containing a methacrylate monomer group and a PV moiety was prepared via nucleophilic substitution between 2-chloroethyl methacrylate (CEMA) and penicillin V potassium (PVK). The PV-based PAC was synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization of the MAC with hydroxyethyl methacrylate (HEMA), and further characterized by 1H NMR and gel permeation chromatography (GPC) analysis. Antibiotic resistance was investigated by passaging bacteria in low concentrations of the antibiotic for 19 days, followed by a 48 h challenge at higher concentrations. Our results suggest that the development of antibiotic resistance is unlikely. Zone of inhibition (ZOI) assays revealed no clearing zones around PV-containing resins indicating minimal antibiotic leakage from the material. Similarly, MTT assay demonstrated that the antibiotic-containing specimens did not release cytotoxic byproducts that may inhibit human gingival fibroblast growth. Counting of colony-forming units in an S. mutans biofilm model was used to assess bacterial survival at baseline and after subjecting the antibiotic-containing resin specimens to an enzymatic challenge for 30 days. Significantly reduced bacterial counts were observed as the biofilm aged from 24 to 72 h, and salivary enzymatic exposure did not reduce the antibacterial efficacy of the discs, suggesting that PV-resin will be effective in reducing the re-incidence of dental caries.

Antimicrobial antidegradative dental adhesive preserves restoration-tooth bond

OBJECTIVE

Assess the ability of an antimicrobial drug-releasing resin adhesive, containing octenidine dihydrochloride (OCT)-silica co-assembled particles (DSPs), to enhance the biostability and preserve the interfacial fracture toughness (FT) of composite restorations bonded to dentin. Enzyme-catalyzed degradation compromises the dental restoration-tooth interface, increasing cariogenic bacterial infiltration. In addition to bacterial ingress inhibition, antimicrobial-releasing adhesives may exhibit direct interfacial biodegradation inhibition as an additional benefit.

METHODS

Mini short-rod restoration bonding specimens with total-etch adhesive with/without 10% wt. DSPs were made. Interfacial fracture toughness (FT) was measured as-manufactured or post-incubation in simulated human salivary esterase (SHSE) for up to 6-months. Effect of OCT on SHSE and whole saliva/bacterial enzyme activity was assessed. Release of OCT outside the restoration interface was assessed.

RESULTS

No deleterious effect of DSPs on initial bonding capacity was observed. Aging specimens in SHSE reduced FT of control but not DSP-adhesive-bonded specimens. OCT inhibited SHSE degradation of adhesive monomer and may inhibit endogenous proteases. OCT inhibited bacterial esterase and collagenase. No endogenous collagen breakdown was detected in the present study. OCT increased human saliva degradative esterase activity below its minimum inhibitory concentration towards S. mutans (MIC), but inhibited degradation above MIC. OCT release outside restoration margins was below detection.

SIGNIFICANCE

DSP-adhesive preserves the restoration bond through a secondary enzyme-inhibitory effect of released OCT, which is virtually confined to the restoration interface microgap. Enzyme activity modulation may produce a positive-to-negative feedback switch, by increasing OCT concentration via biodegradation-triggered release to an effective dose, then subsequently slowing degradation and degradation-triggered release.

Physical properties and cytotoxicity of antimicrobial dental resin adhesives containing dimethacrylate oligomers of Ciprofloxacin and Metronidazole

OBJECTIVE

Antimicrobial oligomers synthesized from ciprofloxacin (CF) and metronidazole (MN) were investigated for their potential use in dental adhesives.

METHODS

Susceptibility of the cariogenic bacterium Streptococcus mutans UA159 to CF, MN, and CF/MN combination was evaluated. Hydrolytic stability and drug release from the oligomers was studied in buffer and simulated human salivary esterase conditions. Cytotoxicity of films with 15wt% drug oligomers co-polymerized with commercial monomers were assessed using human gingival fibroblasts (HGFs). In-house adhesives were prepared and characterized for viscosity. Polymerized films were analysed for gel content and water swelling. Interfacial fracture toughness (K_IC) of composites bonded to dentin by either a 2 or 3-step etch-and-rinse approach using the in-house formulated adhesives was measured.

RESULTS

The respective minimum inhibitory concentration for CF and MN against S. mutans was 0.7 and 2400μg/mL, with the combination having an additive effect (0.35μg/mL CF with 1200μg/mL MN). Antibiotics were released upon hydrolysis of the oligomers. Films containing the drug oligomers were not cytotoxic against HGFs. Replacing 2-hydroxyethyl methacrylate with the drug oligomers increased the viscosity of the experimental adhesives, reduced gel content, and decreased swelling of films in water. Antimicrobial adhesives demonstrated bonding to dentin with interfacial K_IC values comparable to the in-house control in the 2-step application, and with slightly lower K_IC values in the 3-step approach.

SIGNIFICANCE

The antimicrobial oligomers can be incorporated into dental adhesive systems using formulations that show comparable fracture toughness to commercial materials, and may provide a means to deliver local antimicrobial drug release at the marginal interface.

Biostable, antidegradative and antimicrobial restorative systems based on host-biomaterials and microbial interactions

OBJECTIVES

Despite decades of development and their status as the restorative material of choice for dentists, resin composite restoratives and adhesives exhibit a number of shortcomings that limit their long-term survival in the oral cavity. Herein we review past and current work to understand these challenges and approaches to improve dental materials and extend restoration service life.

METHODS

Peer-reviewed work from a number of researchers as well as our own are summarized and analyzed. We also include yet-unpublished work of our own. Challenges to dental materials, methods to assess new materials, and recent material improvements and research directions are presented.

RESULTS

Mechanical stress, host- and bacterial-biodegradation, and secondary caries formation all contribute to restoration failure. In particular, several host- and bacterial-derived enzymes degrade the resin and collagen components of the hybrid layer, expanding the marginal gap and increasing access to bacteria and saliva. Furthermore, the virulence of cariogenic bacteria is up-regulated by resin biodegradation by-products, creating a positive feedback loop that increases biodegradation. These factors work synergistically to degrade the restoration margin, leading to secondary caries and restoration failure. Significant progress has been made to produce hydrolytically stable resins to resist biodegradation, as well as antimicrobial materials to reduce bacterial load around the restoration. Ideally, these two approaches should be combined in a holistic approach to restoration preservation.

SIGNIFICANCE

The oral cavity is a complex environment that poses an array of challenges to long-term material success; materials testing conditions should be comprehensive and closely mimic pathogenic oral conditions.

Responsive antimicrobial dental adhesive based on drug-silica co-assembled particles

Most dental resin composite restorations are replacements for failing restorations. Degradation of the restoration-tooth margins by cariogenic bacteria results in recurrent caries, a leading cause for restoration failure. Incorporating antimicrobial agents in dental adhesives could reduce interfacial bacterial count and reduce recurrent caries rates, inhibit interfacial degradation, and prolong restoration service life, while minimizing systemic exposure. Direct addition of antimicrobial compounds into restorative materials have limited release periods and could affect the integrity of the material. Attempts to incorporate antimicrobial within mesoporous silica nanoparticles showed theoretical promise due to their physical robustness and large available internal volume, yet yielded short-term burst release and limited therapeutic payload. We have developed novel broad-spectrum antimicrobial drug-silica particles co-assembled for long-term release and high payload incorporated into dental adhesives. The release of the drug, octenidine dihydrochloride, is modulated by the oral degradative environment and mathematically modeled to predict effective service life. Steady-state release kills cariogenic bacteria, preventing biofilm formation over the adhesive surface, with no toxicity. This novel material could extend dental restoration service life and may be applied to other long-term medical device-tissue interfaces for responsive drug release upon bacterial infection.

STATEMENT OF SIGNIFICANCE

This study describes a novel dental adhesive that includes a broad-spectrum antimicrobial drug-silica co-assembled particles for long-term antimicrobial effect. The release of the drug, octenidine dihydrochloride, is modulated by the oral degradative environment and mathematically modeled to predict effective release throughout the service life of the restoration. Steady-state drug-release kills caries-forming bacteria, preventing biofilm formation over the adhesive surface, without toxicity. This novel material could extend dental restoration service life and may be applied to other long-term medical device-tissue interfaces for responsive drug release upon bacterial infection. Since recurrent cavities (caries) caused by bacteria are the major reason for dental filling failure, this development represents a significant contribution to the biomaterials field in methodology and material performance.