Mechanical behavior of CAD/CAM occlusal ceramic reconstruction assessed by digital color holography

Modeling of speckle decorrelation in digital Fresnel holographic interferometry

This paper presents analytical modeling of the speckle decorrelation noise in digital Fresnel holographic interferometry. The theoretical analysis is carried out by considering the complex coherence factor between two speckled images from two digitally reconstructed holograms at two different instants. The expression giving the modulus of the coherence factor is established and depends on the local surface deformation and parameters from the holographic setup. The analysis is supported by realistic simulations and experiments. Both simulations and experimental results exhibit a very good agreement with the theoretical prediction.

Behavior of CAD/CAM ceramic veneers under stress: A 3D holographic study

OBJECTIVES

Ceramic veneers restorations may undergo damages, such as cracks, fractures, or debonding. Full-field measurements must be carried out in order to visualize and analyze the strain fields. This paper demonstrates that digital holography permits to investigate the mechanical behavior under stress of a natural incisor and a natural incisor reconstructed with CAD/CAM ceramic veneer.

METHODS

The facial surface of a maxillary central incisor is prepared to receive a monolithic ceramic reconstruction manufactured using a chairside computer-aided design and computer aided manufacturing (CAD/CAM) system (Cerec AC® system, Sirona Dental System®, Bensheim, Germany). One incisor is kept intact for comparison. The samples are sectioned longitudinally to obtain a planar observation of the region of interest. A mechanical indentation head and digital holographic set-ups permit a full-field, contact-less and single-shot measurement of the three-dimensional displacement fields at the surface of the tooth sample when subjected to load. Stain fields are then estimated and comparison of the results between two samples can be carried out.

RESULTS

3D displacement, fields and strain fields are measured and highlight the behavior of the region of interest in three directions of space for the ceramic veneer and the natural incisor. The strain maps reveal the local behavior, especially the concentration or the sudden change in strain. The transition zones are clearly observed, particularly for the veneered sample.

CONCLUSION

Digital holography highlights the localization of stress concentration zones in regions of interest and yields comparative analysis between samples with different tooth preparations.

SIGNIFICANCE

holography permits to visualize and compare the mechanical response of the ceramic veneer and natural tooth. This helps choosing the mechanical properties of the bonding interface.

Effect of various digital cement space settings on the adaptation of CAD/CAM occlusal veneer "micro-ct evaluation"

The aim was to evaluate the adaptation of CAD/CAM occlusal veneer with different cement space settings using micro CT scan. Three groups of IPS e.max-CAD lithium disilicate occlusal veneers with different cement space settings (30, 40, and 50 µm) were produced. A circle with 20 different diameters was centered at the center of the same image position of every scanned specimen using micro CT scan to measure four different locations [Occlusal (OCG), axial (AXG), Marginal (MAG), and absolute marginal discrepancy values (AMD)]. Kruskal-Wallis test revealed that there were no statistical differences between (OCG), (AXG), and (AMD) tested groups (p>0.05), and statistical differences between (MAG) group and other two groups (p<0.05). An increase in the digital cement space significantly improved the marginal fit of IPS e.max-CAD occlusal veneer.

Fracture load of CAD/CAM ultrathin occlusal veneers luted to enamel or dentin

OBJECTIVES

To evaluate, in vitro, the fracture load of IPS e.max CAD occlusal veneers at thicknesses of either 0.3 or 0.6 mm luted to enamel or dentin.

MATERIALS AND METHODS

Fifty human molars were randomly distributed into five groups (n = 10): G1 - healthy teeth (control); G2-0.3-mm-thick veneers luted to enamel; G3-0.6-mm-thick veneers luted to enamel; G4-0.3-mm-thick veneers luted to dentin; and G5-0.6-mm-thick veneers luted to dentin. After the luting procedures, the specimens were immersed in distilled water at 37°C for 24 hours and then subjected to mechanical loading (10⁶  cycles at 200 N load). The specimens were subjected to a fracture load test in a universal testing machine. Two-way ANOVA and Tukey's test (α = 0.05) were used to analyze data.

RESULTS

Only the thickness factor was significant (P = .002). Values of fracture load followed by distinct letters represent significant differences (P < .05): G1 (3204 N ± 730)^ab ; G2 (3144 N ± 729)^ab ; G3 (2489 N ± 606)^b ; G4 (3591 N ± 776)^a ; and G5 (2770 N ± 598)^ab .

CONCLUSION

IPS e.max ultrathin occlusal veneers luted to enamel or dentin obtained fracture load comparable to that of the healthy tooth.

CLINICAL SIGNIFICANCE

IPS e.max CAD ultrathin occlusal veneers at 0.3 or 0.6-mm-thick seem to provide good perspectives in relation to the clinical use.

Measuring tooth vibrations induced during cavity preparation with time-averaged holography and its influence on near vision acuity in dentists

The aim of this study was to quantify vibrations and their influence on visual acuity. The study consisted of two parts, laboratory and clinical. Time-averaged holographic interferometry (TAHI) method was used in laboratory for measuring the amplitude of tooth vibrations induced by dental handpiece. The amplitudes of tooth vibrations were measured for the three diameters and three speeds. The larger diameter coupled with increasing speed resulted in greater vibration amplitudes, whereby a maximum amplitude of less than one micrometer was detected. For quantifying the natural visual acuity for the corresponding tooth vibrations, we have used the clinical condition approach with miniaturized Snellen optotype as an assessing tool. Central visual acuity did not display variance in visual acuity at rest or under load. Results indicate that the vibrations induced during cavity preparation are not sufficient to negatively affect visual acuity of dentists.

Optimal processing scheme for restoration of phase data corrupted by strong decorrelation noise and dislocations

The presence of speckle noise and dislocations makes phase restoration potentially difficult in quantitative phase imaging and metrology. Unfortunately, there is no appropriate approach to deal with phase data corrupted by high speckle noise and phase dislocations. Usually, processing schemes may deal with low-pass phase filtering, phase unwrapping, or phase inpainting. This paper discusses the efficient processing to deal with noisy phase maps corrupted with phase dislocations. Six processing schemes, combining four operations, are evaluated. The investigation is carried out by realistic numerical simulations in which strong decorrelation phase noise and phase dislocations are generated. As a result, most robust and faster processing is established. The applicability of the optimal scheme is demonstrated through deformation measurement in dental materials.

Comparative study of multi-look processing for phase map de-noising in digital Fresnel holographic interferometry

This paper presents a comparative study of multi-look approaches for de-noising phase maps from digital holographic interferometry. A database of 160 simulated phase fringe patterns with eight different phase fringe patterns with fringe diversity was computed. For each fringe pattern, 20 realistic noise realizations are generated in order to simulate a multi-look process with 20 inputs. A set of 22 de-noising algorithms was selected and processed for each simulation. Three approaches for multi-look processing are evaluated. Quantitative appraisal is obtained using two metrics. The results show good agreement for algorithm rankings obtained with both metrics. One singular and highly practical result of the study is that a multi-look approach with average looks before noise processing performs better than averaging computed with all de-noised looks. The results also demonstrate that the two-dimensional windowed Fourier transform filtering exhibits the best performance in all cases and that the block-matching 3D (BM3D) algorithm is second in the ranking.

Cortical bone quality affectations and their strength impact analysis using holographic interferometry

It is now accepted that bone strength is a complex property determined mainly by three factors: quantity, quality and turnover of the bone itself. Most of the patients who experience fractures due to fragility could never develop affectations related to bone mass density (i.e. osteoporosis). In this work, the effect of secondary bone strength affectations are analyzed by simulating the degradation of one or more principal components (organic and inorganic) while they are inspected with a nondestructive optical technique. From the results obtained, a strong correlation among the hydroxyapatite, collagen and water is found that determines the bone strength.