Simultaneous passive sampling of hydrophilic and hydrophobic emerging organic contaminants in water

Highly sensitive passive sampling of new pollutants in urban reclaimed water using hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane

Urban reclaimed water is important water resource in China, while the residual new pollutants in the water largely challenge their safety for further use. China's action program for the management of new pollutants (also known as emerging contaminants) requires effective method for monitoring diverse new pollutants in water. This work proposed a highly sensitive passive sampling method for monitoring diverse new pollutants in urban reclaimed water. Hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membranes (HECAMs) were dynamically deployed in self-developed continuous flow integrative sampling device (CFISD) for sampling four types of new pollutants with wide polarity ranges (1.11 < log Kow < 9.49) in a reclaimed water network for landscape irrigation in Beijing, China. The estimated equilibrium partition ratios of most chemicals between HECAM and water were over 104, which would provide low detection limits. In the 7-d high-efficiency deployment, thirty new pollutants were detected, which indicated incompletely removal of various new pollutants in wastewater treatment process. The dynamical accumulation data were successfully fitted by first-order kinetic model and different contaminants reached different accumulation phases in the HECAMs during 7 d. Acceptable and steady uptake rate constants and sampling rates were obtained with the use of CFISD in field sampling. The estimated time-weighted average concentrations for contaminants had wide concentration range and were from 0.03 ng L-1 (pendimethalin) to 3,394 ng L-1 (dibutyl phthalate) and this may lead to environmental risk for further use the reclaimed water. Dynamical deployment results also provided sensitive information of concentration fluctuations and twelve pollutants showed concentration fluctuations during the sampling period. In summary, HECAM showed high sensitivities and credible performance of monitoring diverse new pollutants in the urban reclaimed water.

Evaluation of ceramic passive samplers using a mixed-mode strong cation-exchange sorbent to monitor polar contaminants in river water

Although most of the analytical methods developed for the monitoring of contaminants in environmental waters are based on discrete grab sampling, an alternative of increasing interest is the use of passive sampling. Methods based on passive sampling provide the sampling and pre-concentration of the analytes in-situ, which makes the sample treatment less time consuming and costly than using discrete grab sampling. In this study, ceramic passive samplers (CPSs) using mixed-mode strong cation-exchange sorbent (Oasis MCX) as retention phase were evaluated for the determination of a group of 21 therapeutic and illicit drugs and some of their metabolites in river water samples that were determined by liquid chromatography-tandem mass spectrometry. After assessing the stability of the analytes, the CPSs were calibrated for 9 days with bottled water and river water, obtaining, for the 19 stable compounds, sample rates (Rs) ranging between 0.180 and 1.767 mL/day and diffusion coefficients (De) between 2.02E-8 and 2.81E-7 cm2/s. Once calibrated, CPSs were deployed for the determination of contaminants in the Ebre River, with good reproducibility, and some of the analytes were determined, including amongst others, gabapentin at 76 ng/L, caffeine at 203 ng/L or diclofenac amine at 57 ng/L. The passive sampling method herein presented is simple and feasible and allows the time-integrated analysis of pharmaceuticals and drugs at trace levels in river water. This study opens the possibility of using other mixed-mode sorbents or other types of sorbents as retaining phase on CPSs for the determination of very polar contaminants in water.

Antibiotic sorption onto microplastics in water: A critical review of the factors, mechanisms and implications

Microplastics as vectors for contaminants in the environment is becoming a topic of public interest. Microplastics have been found to actively adsorb heavy metals, per-fluorinated alkyl substances (PFAS), polychlorinated biphenyls (PCBs), polyaromatic hydrocarbons (PAHs), pharmaceuticals and personal care products (PPCPs) and polybrominated diethers (PBDs) onto their surface. Particular interest in microplastics capacity to adsorb antibiotics needs further attention due to the potential role this interaction plays on antibiotic resistance. Antibiotic sorption experiments have been documented in the literature, but the data has not yet been critically reviewed. This review aims to comprehensively assess the factors that affect antibiotic sorption onto microplastics. It is recognised that the physico- chemical properties of the polymers, the antibiotic chemical properties, and the properties of the solution all play a crucial role in the antibiotic sorption capacity of microplastics. Weathering of microplastics was found to increase the antibiotic sorption capacity by up to 171%. An increase in solution salinity was found to decrease the sorption of antibiotics onto microplastics, in some instances by 100%. pH also has a substantial effect on sorption capacity, illustrating the significance of electrostatic interactions on the sorption of antibiotics onto microplastics. The need for a uniform experimental design when testing antibiotic sorption is highlighted to remove inconsistencies in the data currently presented. Current literature examines the link between antibiotic sorption and antibiotic resistance, however, further studies are still required to fully understand this emerging global crisis.

Passive sampling of diverse pesticides in water by hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane: Kinetics, equilibrium partitioning and field application

Pesticides are useful products for agriculture and human life, but they are often released into surface waters and are hazardous to aquatic ecosystems. Pesticides monitoring in surface waters is challenging due to the great variety, ultratrace levels and nonpoint source pollution of pesticides; however, continuous passive sampling may be conducive to solving these problems. This work evaluated the performance of a newly developed passive sampler (hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane, HECAM) for six types of currently used/present pesticides. The uptake kinetics and equilibrium partitioning of nineteen pesticides in different dissolved concentrations were studied by dynamic accumulation and equilibrium partitioning experiments, respectively. In the dynamic accumulation experiments, pesticides gradually accumulated in the HECAM and followed a first-order kinetic model. The same type of pesticides had roughly comparable accumulation concentrations. The estimated uptake rate constants ranged from 1.04 to 13.5 L g^-1 d^-1, and sampling rates ranged from 0.02 to 0.31 L d^-1 for the pesticides in the HECAM (size of 2 cm × 3 cm). Pesticide accumulation concentrations in the HECAM increased linearly with increasing dissolved concentrations, which means that varying concentrations can also be monitored by the HECAM. In the equilibrium partitioning experiments, the pesticide partitioning behavior at varying dissolved concentrations can be described by the Freundlich model. The calculated equilibrium partition coefficients (log K_D) for pesticides ranged from 3.32 to 4.54, and different pesticide types showed different changes with log K_ow. Comparable results were found when estimating chemical equilibrium partition coefficients by the dynamic accumulation and equilibrium partitioning methods. Field deployment of the HECAM in river waters resulted in the detection of four pesticides, and the measured results were comparable to those of active sampling coupled with liquid-liquid extraction. These results suggest that the HECAM would be a promising strategy for simultaneously monitoring diverse pesticides in waters.

Assessing bioaccumulation potential of sediment associated fipronil degradates in oligochaete Lumbriculus variegatus based on passive sampler measured bioavailable concentration

The degradates of fipronil have equivalent or even more toxicity to non-target aquatic invertebrates. To assess their environmental risks, information of bioaccumulation is required. Currently, little is known about the bioaccumulative property of fipronil degradates in sediment, while it is well known that passive sampler may measure bioavailable concentration (C_free) which links with the environmental effect more tightly than the total environment concentration. The goal of the present study was to characterize bioaccumulation potential in oligochaete Lumbriculus variegatus for a fipronil degradate sulfide. The sediment organic carbon-water partition coefficient (K_OC) was measured with polymethyl methacrylate (PMMA) film passive sampler, and K_OC was used to bridge the gap between biota-sediment accumulation factor (BSAF) and bioconcentration factor (BCF). The bioavailable concentration (C_free)-based K_OC values were 5371 ± 152 and 5013 ± 152 (mL/g OC) for fipronil sulfide (FSI) and sulfone (FSO), respectively. Since the two fipronil degradates were produced continuously in sediment by the parent compound, the time-weighted-average (TWA) concentration of FSI in the sediment was estimated from a bioassay with L. variegatus to calculate BSAF value (0.581 ± 0.211 g OC/g lipid) and BCF (3046 ± 1103 or log 3.48 ± 0.16 mL/g). This approach is able to estimate the C_free-based K_OC and BCF values of fipronil degradate in sediment with ongoing degradation of the parent compound.

Passive sampling hydrophilic and hydrophobic bisphenol analogues using hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane in surface waters

Bisphenol analogues (BPs) are ubiquitous emerging contaminants in water environments and have wide polarity ranges (1.65 < log K_ow < 7.2). Integrated passive sampling strategy rarely contains hydrophilic and hydrophobic organics simultaneously, while the method has good application perspective in monitoring organic contaminants. This work evaluated passive sampling performance for fifteen BPs in a newly developed passive sampler, i.e., hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane (HECAM). In the dynamic accumulation experiments, both hydrophilic and hydrophobic BPs (including moderately hydrophilic BPs) well followed first-order kinetic uptake in the HECAMs. The estimated uptake rate constants, elimination rate constants, and equilibrium partition coefficients for BPs ranged from 4.4 L g^-1 d^-1 to 14.7 L g^-1 d^-1, 0.22 d^-1 to 0.72 d^-1, and 3.99 to 4.64, respectively. The kinetic parameters for BPs in HECAM show limited correlations to log K_ow values, which the rule differs from traditional passive sampler. In the study of elimination kinetics, three deuterium labeled compounds showed incomplete elimination in HECAM and did not follow first-order isotropic exchange kinetics. Dual sorption mechanisms including both adsorption and partition were found for chemicals in HECAM, which the partitioned part could release to water and the adsorbed part could not easily release to water from HECAM. As a result, performance reference compounds (PRCs) calibration may be inapplicable to HLB sorbent-based passive sampler. The field deployment of HECAM in coastal waters of Guangdong, China resulted in the detection of eleven BPs, which indicated that the waters have been polluted by various BPs. Finally, monitoring strategy of simultaneous passive sampling hydrophobic and hydrophilic organic contaminants in surface waters was recommended.

Pesticides in surface freshwater: a critical review

The objective of this study was to critically review studies published up to November 2021 that investigated the presence of pesticides in surface freshwater to answer three questions: (1) in which countries were the studies conducted? (2) which pesticides are most evaluated and detected? and (3) which pesticides have the highest concentrations? Using the Prisma protocol, 146 articles published from 1976 to November 2021 were included in this analysis: 127 studies used grab sampling, 10 used passive sampling, and 9 used both sampling techniques. In the 45-year historical series, the USA, China, and Spain were the countries that conducted the highest number of studies. Atrazine was the most evaluated pesticide (56% of the studies), detected in 43% of the studies using grab sampling, and the most detected in passive sampling studies (68%). The compounds with the highest maximum and mean concentrations in the grab sampling were molinate (211.38 µg/L) and bentazone (53 µg/L), respectively, and in passive sampling, they were oxyfluorfen (16.8 µg/L) and atrazine (4.8 μg/L), respectively. The levels found for atrazine, p,p'-DDD, and heptachlor in Brazil were higher than the regulatory levels for superficial water in the country. The concentrations exceeded the toxicological endpoint for at least 11 pesticides, including atrazine (Daphnia LC₅₀ and fish NOAEC), cypermethrin (algae EC50, Daphnia and fish LC₅₀; fish NOAEC), and chlorpyrifos (Daphnia and fish LC₅₀; fish NOAEC). These results can be used for planning pesticide monitoring programs in surface freshwater, at regional and global levels, and for establishing or updating water quality regulations.

Exploring the influence of concentration fluctuation and matrix effects on a passive sampler of triolein-embedded cellulose acetate membrane measuring polychlorinated biphenyls in water

A membrane of triolein-embedded cellulose acetate membrane (TECAM), as an integrative passive sampler, was applied to adsorb 28 polychlorinated biphenyls (PCBs) from pure water and sea water in order to probe into the influence of concentration fluctuation and water matrix. The results demonstrated the temporal variations of PCBs concentrations in TECAM followed the first-order kinetics model. The periodic refreshment of solution and matrix effects of sea water significantly prolonged the time that PCBs reached equilibrium stage. The refreshment facilitated the uptake mass in TECAM. On the contrary, the matrix effects of sea water and dissolved organic matter (DOM) declined the PCBs absorption to TECAM. The average logK_P values of PCBs in pure water were about 1.2 log unit higher than those in sea water in the experiments that the solution was not refreshed, while the difference of average logK_P values narrowed to 0.3 log unit if the PCBs solutions were periodically refreshed. The correlation between logK_P and logK_OW values fitted the quadratic curve well, which was similar to semi-permeable membrane device (SPMD). The appropriate sampling times (t_94%) ranged from 98.8 to 819 h (mean 500 h) for pure water with refreshment, much longer than those in sea water with refreshment (80.1~410 h, mean 189 h). The t_94% values in the solution with high DOM content increased significantly, up to 409 h. Furthermore,  comparing the two experiments that the spiked pure water and sea water solution were refreshed frequently, the estimated sampling rates (R_s) in pure water (0.154~2.06 L/day with a mean value of 0.605 L/day) were slightly lower than those in sea water (0.292~3.84 L/day with a mean value of 1.69 L/day). However, the R_s values in sea water with DOM declined sharply to 0.042 L/day. Therefore, concentration fluctuation, matrix effect, and DOM contents of sea water evidently posed significant influence on dynamic parameters of TECAM absorption, which would be screened and probed detailed in future.

Integrated passive sampling and fugacity model to characterize fate and removal of organophosphate flame retardants in an anaerobic-anoxic-oxic municipal wastewater treatment system

It is crucial to deeply understand the fate and removal mechanism of various organophosphate flame retardants (PFRs) in specified wastewater treatment processes. However, concentration fluctuation and matrix effect in wastewater challenge quantification of PFR flux for both field observation and model validation. We present measured seasonal distribution profiles of time-weighted average (TWA) concentrations by in situ hydrophobic and polar passive samplers and modeled mass transport and transformation by means of fugacity for 11 PFRs with varied structures in an anaerobic-anoxic-oxic (A-A-O) municipal wastewater treatment system, and provided a systematic approach to characterize fate and removal mechanism of PFRs in major compartments via various treatment processes. We find evidence that PFRs have a unique structural-dependent fate and removal in the A-A-O system. Hydrophilic chlorinated-PFRs present persistent in all major compartments and dominate in effluents with significant variations; alkyl-PFRs are majorly reduced by biodegradation; whereas hydrophobic aryl-PFRs have the highest removal percentage, contributed by both sorption on solids and biotransformation. Sensitive analysis shows the most influential operation parameters on removal efficiency varied among the PFRs with different properties. We also conclude passive sampling can be effectively applied to estimate TWA wastewater concentrations and to validate fugacity model prediction.

Accumulation and passive sampling of bisphenol analogues using triolein-embedded cellulose acetate membrane in waters

Bisphenol analogues (BPs) are emerging contaminants that have been widely detected in water environments. The presence of substituted hydrophilic and hydrophobic groups in the molecule may lead to unclear performance in passive sampling. This study tested the accumulation capacity and passive sampling of fifteen BPs in a triolein-embedded cellulose acetate membrane (TECAM) passive sampler. In a dynamic accumulation experiment, twelve hydrophobic BPs accumulated in the TECAM with concentrations ranging from 251 ng g^-1 to 6283 ng g^-1, and three hydrophilic BPs did not accumulate during the 72 h exposure duration. BPs accumulations were determined by the hydrophilic and hydrophobic substituent groups in molecule structures. The estimated passive sampling parameters showed correlations to both the log K_ow values and chemical structures, and compared to other contaminants, such as organophosphorus flame retardants. Environmental factors, including flow rate, temperature, salinity, and pH, that affect the accumulation of BPs in the TECAM were tested, and the flow rate was found to be an important factor affecting the uptake rate. The isotropic exchange kinetics for BPs in the TECAM were verified, and the results indicated that BPs can be calibrated with performance reference compounds (PRCs) in field applications. Finally, a field deployment of TECAM in river waters successfully estimated the time-weighted concentrations of two hydrophobic BPs. To address the inherent weaknesses of TECAM in sampling hydrophilic and moderately hydrophobic BPs, future studies should explore alternative passive samplers, such as hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membranes, to sample BPs in surface waters.

Crown Ether-Immobilized Cellulose Acetate Membranes for the Retention of Gd (III)

This study presents a new, revolutionary, and easy method of separating Gd (III). For this purpose, a cellulose acetate membrane surface was modified in three steps, as follows: firstly, with aminopropyl triethoxysylene; then with glutaraldehyde; and at the end, by immobilization of crown ethers. The obtained membranes were characterized by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), through which the synthesis of membranes with Gd (III) separation properties is demonstrated. In addition, for the Gd (III) separating process, a gadolinium nitrate solution, with applications of moderator poison in nuclear reactors, was used. The membranes retention performance has been demonstrated by inductively coupled plasma mass spectrometry (ICP-MS), showing a separation efficiency of up to 91%, compared with the initial feed solution.

Monitoring of emerging contaminants of concern in the aquatic environment: a review of studies showing the application of effect-based measures

Water scarcity is increasingly a global cause of concern mainly due to widespread changes in climate conditions and increased consumptive water use driven by the exponential increase in population growth. In addition, increased pollution of fresh water sources due to rising production and consumption of pharmaceuticals and organic chemicals will further exacerbate this concern. Although surface water contamination by individual chemicals is often at very low concentration, pharmaceuticals for instance are designed to be efficacious at low concentrations, creating genuine concern for their presence in freshwater sources. Furthermore, the additive impact of multiple compounds may result in toxic or other biological effects that otherwise will not be induced by individual chemicals. Globally, different legislative frameworks have led to pre-emptive efforts which aim to ensure good water ecological status. Reports detailing the use and types of effect-based measures covering specific bioassay batteries that can identify specific mode of actions of chemical pollutants in the aquatic ecosystem to evaluate the real threat of pollutants to aquatic lives and ultimately human lives have recently emerged from monitoring networks such as the NORMAN network. In this review, we critically evaluate some studies within the last decade that have implemented effect-based monitoring of pharmaceuticals and organic chemicals in aquatic fauna, evaluating the occurrence of different chemical pollutants and the impact of these pollutants on aquatic fauna with special focus on pollutants that are contaminants of emerging concern (CEC) in urban wastewater. A critical discussion on studies that have used effect-based measures to assess biological impact of pharmaceutical/organic compound in the aquatic ecosystem and the endpoints measurements employed is presented. The application of effect-based monitoring of chemicals other than assessment of water quality status is also discussed.

eDNA metabarcoding revealed differential structures of aquatic communities in a dynamic freshwater ecosystem shaped by habitat heterogeneity

Freshwater ecosystems have been threatened by complicated disturbances from both natural and anthropogenic variables, especially in dynamic and complex river basins. The environmental DNA (eDNA)-based approach provides a broader spectrum and higher throughput way of biomonitoring for biodiversity assessment compared with traditional morphological survey. Most eDNA metabarcoding studies have been limited to a few specific taxa/groups and habitat scopes. Here we applied the eDNA metabarcoding to characterize the structures and spatial variations of zooplankton and fish communities among different habitat types in a highly dynamic and complex freshwater ecosystem of the Daqing River basin (DRB). The results showed that varied species spectra of zooplankton and fish communities were identified and unique dominant species occurred across habitats. Additionally, markedly spatial distributions of biotic community structures were observed in areas with different habitat characteristics. Natural variables, including geographic distances and gradient ratio, as well as anthropogenic factors of chemical oxygen demand (COD) and organic chemicals demonstrated significant effects but different outcomes on the structures of zooplankton and fish communities. Moreover, the relative abundances of specific aquatic taxa were associated with the gradient of particular environmental variables. This case study verified the distribution patterns and differentiation mechanisms of biotic communities under habitat heterogeneity could be captured by application of eDNA biomonitoring. And habitat-specific and even species-specific environmental stressors would be diagnosed for improving management of complex river basins.

Spatial pattern analysis reveals multiple sources of organophosphorus flame retardants in coastal waters

Organophosphorus flame retardants (PFRs) are a group of emerging contaminants which have been detected in worldwide waters. However, source of various PFRs in the large-scale area like coastal water environment have not been clearly revealed. In this study, fifteen PFRs in coast of Guangdong-Hong Kong-Macao Greater Bay area (GBA), China were investigated, and a method of spatial pattern analysis was firstly used for pollution source identification. Seawater samples from different segments of GBA coast were analyzed and thirteen PFRs were quantified with total concentrations ranging from 32.7 to 1032.7 ng L^-1. GBA coasts have been seriously polluted by PFRs. A hierarchical cluster analysis of the PFR concentrations in different GBA sites showed significant spatial distributions for different types of PFRs. A series of correlation analysis between PFRs distributions and spatial pattern of GBA socio-economic indicators were performed, and multiple sources including human settlement, wastewater, manufacture, construction industry, vehicles, and shipping transport were found to be correlated to PFRs pollutions in the coasts. This study indicates that spatial pattern analysis based on statistical analysis would be a promising method of analyzing environmental data and exploring pollution source in large-scale area.

Interactions between microplastics, pharmaceuticals and personal care products: Implications for vector transport

Microplastics are well known for vector transport of hydrophobic organic contaminants, and there are growing concerns regarding their potential adverse effects on ecosystems and human health. However, recent studies focussing on hydrophilic compounds, such as pharmaceuticals and personal care products (PPCPs), have shown that the compounds ability to be adsorbed onto plastic surfaces. The extensive use of PPCPs has led to their ubiquitous presence in the environment resulting in their cooccurrence with microplastics. The partitioning between plastics and PPCPs and their fate through vector transport are determined by various physicochemical characteristics and environmental conditions of specific matrices. Although the sorption capacities of microplastics for different PPCP compounds have been investigated extensively, these findings have not yet been synthesized and analyzed critically. The specific objectives of this review were to synthesize and critically assess the various factors that affect the adsorption of hydrophilic compounds such as PPCPs on microplastic surfaces and their fate and transport in the environment. The review also focuses on environmental factors such as pH, salinity, and dissolved organics, and properties of polymers and PPCP compounds, and the relationships with sorption dynamics and mechanisms. Furthermore, the ecotoxicological effects of PPCP-sorbed microplastics on biota and human health are also discussed.

Environmental prioritization of pesticide in the Upper Citarum River Basin, Indonesia, using predicted and measured concentrations

A novel screening method was developed to prioritize aquatic and human health risks of pesticides based on usage data, runoff modelling and effect prediction. An important asset of this new method is that it does not require measured concentration data, which are often unavailable or difficult to obtain in low- and middle-income countries like Indonesia. The method was applied to prioritize 31 agricultural pesticides used in the Upper Citarum River Basin in West Java, Indonesia. Ranking of pesticides based on predicted concentrations generally showed good agreement with ranking based on concentrations measured by passive sampling. The individual pesticide intake through the consumption of river water was predicted to cause negligible human health risks, but substantial aquatic risks (i.e. PEC/PNEC >1) were predicted for profenofos (5.2.E+01), propineb (3.6.E+01), chlorpyrifos (2.6.E+01), carbofuran (1.7.E+01), imidacloprid (9.4.E+00), methomyl (7.6.E+00) and chlorantraniliprole (3.6.E+00). In order to protect the aquatic environment, water managers are advised to take measures to reduce the use and runoff of these pesticides in the UCRB. The screening assessment can be further refined by performing additional effect studies for some pesticides, pesticide mixtures and validation of the predicted water concentrations by targeted measurements.

Contaminants of emerging concern in aquatic environment: Occurrence, monitoring, fate, and risk assessment

The present work provides a review focusing on contaminants of emerging concern (CECs) in aquatic environment, with an emphasis on their occurrence, monitoring, fate, and risk assessment in the research published in the scientific literature in 2019. Several studies revealed that these organic contaminants were detected in many water bodies and suspect, nontarget, and target screening provided an efficient detection for the co-existing organic substances with complex components. Wastewater resource recovery facilities were concurrently considered as a central source, and several specific chemicals have been found to be used as chemical markers to track the source of CECs in some urban watersheds. Reliable monitoring, reliable fate/toxicity assessment, and effective removal that consider CECs as a heterogeneous group rather than single substances will be the challenges for the research community in the future.

Distribution, sources and transport of organophosphorus flame retardants in the water and sediment of Ny-Ålesund, Svalbard, the Arctic

Organophosphorus flame retardants (PFRs) are contaminants of emerging concern which have been detected globally. However, little information on PFRs in the Arctic freshwater environment is currently available. In this study, both hydrophilic and hydrophobic PFRs in the water and sediment of four areas (town, surroundings, coastal marine water, and glacier melt runoff) near Ny-Ålesund Svalbard were investigated by time-integrated passive sampling (water) and grab sampling (sediment). Seven kinds of PFRs were found in the Arctic waters with individual freely dissolved concentrations from 0.007 ng L^-1 to 355 ng L^-1, and the concentrations of chlorinated PFRs were 3-4 orders of magnitude higher than those of non-chlorinated PFRs. The distribution of different PFRs in freshwater showed significant spatial differences among the different areas, and the town was found to have most kinds of PFRs and highest PFRs concentrations. The sources and transport of different kinds of PFRs were explored based on a spatial overlay analysis of the contaminant distributions, environmental conditions, and PFR applications. As a result, human settlements, industrial activities, atmospheric deposition, and transportation in Ny-Ålesund were proposed to be related to the pollution of different PFRs at Ny-Ålesund. The PFRs in the inshore marine water were found to be affected by both local ship contamination and ocean current transport. Furthermore, nine PFRs were detected in the sediments of Ny-Ålesund. Accumulation of different PFRs in the Arctic sediment was found to be dominated by their physico-chemical properties (polarity).

Using silicone rubber and polyvinylchloride as equilibrium passive samplers for rapid and sensitive monitoring of pyrethroid insecticides in aquatic environments

Passive sampling to regularly identify the occurrence of pyrethroid insecticides in urban streams is a crucial work of risk management with respect to intrinsic toxicity of pyrethroids to aquatic organisms. Polymeric films, based on an equilibrium sampling principle, have found increasing use as passive samplers for hydrophobic contaminants. Herein, we investigated two thin-film samplers, namely silicone rubber (SR) and polyvinylchloride (PVC), compatible with a suite of 8 pyrethroids, for measuring freely dissolved concentrations (C_free) in water. The characteristics of SR and PVC samplers were estimated in terms of equilibrium partitioning coefficients (K_f) with log units of 3.90-4.67 and sampling rates (R_s) of 0.011-0.016 L/h. The parameters were correlated positively with octanol-water partition coefficients of the compounds, whereas independent on water solubility. A strong agreement between C_free obtained from the two samplers was observed in a range of 0.1-10 μg/L for pyrethroids under laboratory simulated conditions. Both of SR and PVC were confirmed as equilibrium samplers with faster sampling rates of pyrethroids that equilibrated on films within only one week, and higher accumulation at factors of 5.3-12.5 and 1.5-2.4 compared to a performance reference compound (PRC)-preload sampler. Additionally, the comparable results of the two passive sampling methods in multiple field applications indicated that the direct deployment of the two samplers without PRCs calibration can provide reliable assessment of trace concentrations. This study demonstrated the routine utilization of SR and PVC as promising tools for rapid and sensitive in-situ monitoring of pyrethroids, and indicators for the bioavailability against total chemical concentrations in variable aquatic environments.

Synthesis and Characterization of Cellulose Acetate Membranes with Self-Indicating Properties by Changing the Membrane Surface Color for Separation of Gd(III)

This study presents a new, revolutionary, and easy method for evaluating the separation process through a membrane that is based on changing the color of the membrane surface during the separation process. For this purpose, a cellulose acetate membrane surface was modified in several steps: initially with amino propyl triethoxysilane, followed by glutaraldehyde reaction and calmagite immobilization. Calmagite was chosen for its dual role as a molecule that will complex and retain Gd(III) and also as an indicator for Gd(III). At the contact with the membrane surface, calmagite will actively complex and retain Gd(III), and it will change the color of the membrane surface during the complexation process, showing that the separation occurred. The synthesized materials were characterized by Fourier transform infrared spectroscopy (FT-IR), thermal analysis (TGA-DTA), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy, demonstrating the synthesis of membrane material with self-indicating properties. In addition, in the separation of the Gd(III) process, in which a solution of gadolinium nitrate was used as a source and as a moderator in nuclear reactors, the membrane changed its color from blue to pink. The membrane performances were tested by Induced Coupled Plasma–Mass Spectrometry (ICP-MS) analyses showing a separation process efficiency of 86% relative to the initial feed solution.

Hydrolysis of Amisulbrom in Buffer Solutions and Natural Water Samples: Kinetics and Products Identification

In this study, the hydrolysis of amisulbrom in buffer solutions and natural water samples were investigated. Effects of pH and temperature were tested in buffer solutions. Amisulbrom was stable in acidic and neutral aqueous solutions at 25°C, while quickly hydrolyzed with a half-life of 4.5 days (25°C) at pH 9.0. The kinetics rate equation was determined as k = 1.0234 × 10¹⁰ exp (-61.3760/R·T) (R² = 0.9642) for hydrolysis of amisulbrom at pH 9.0. The pH, ionic strength, and solubility were important factors influencing the hydrolysis of amisulbrom in natural water samples. Furthermore, three hydrolysis products were separated and identified in buffer solution (pH 9.0) and natural water samples. A tentative transformation mechanism of amisulbrom was proposed to rationalize the formation of HPs (hydrolysis products) based on their structural identification, DFT (density functional theory), and hydrolysis profiles. Toxicity prediction using the quantitative structure-activity relationship model revealed that the HP-I, and HP-II were more toxic than the parent amisulbrom. This investigation was the first to evaluate the behavior of amisulbrom hydrolysis in aquatic systems.

Sorption kinetics of parent and substituted PAHs for low-density polyethylene (LDPE): Determining their partition coefficients between LDPE and water (KLDPE) for passive sampling

Low-density polyethylene (LDPE) has been widely used as a sorbent for passive sampling of hydrophobic organic contaminants (HOCs) in aquatic environments. However, it has seen only limited application in passive sampling for measurement of freely dissolved concentrations of parent and substituted PAHs (SPAHs), which are known to be toxic, mutagenic and carcinogenic. Here, the 16 priority PAHs and some typical PAHs were selected as target compounds and were simultaneously determined by gas chromatography-mass spectrometer (GC-MS). Some batch experiments were conducted in the laboratory to explore the adsorption kinetics of the target compounds in LDPE membranes. The results showed that both PAHs and SPAHs could reach equilibrium status within 19-38 days in sorption kinetic experiments. The coefficients of partitioning between LDPE film (50 μm thickness) and water (K_LDPE) for the 16 priority PAHs were in good agreement with previously reported values, and the values of K_LDPE for the 9 SPAHs are reported in this study for the first time. Significant linear relationships were observed, i.e., log K_LDPE = 0.705 × log K_OW + 1.534 for PAHs (R² = 0.8361, p < 0.001) and log K_LDPE = 0.458 × log K_OW + 3.092 for SPAHs (R² = 0.5609, p = 0.0077). The selected LDPE film was also proven to meet the condition of "zero sink" for the selected target compounds. These results could provide basic support for the configuration and in situ application of passive samplers.