Solid state transformations in consequence of electrospraying – A novel polymorphic form of piroxicam

Electrospinning technologies for the delivery of Biopharmaceuticals: Current status and future trends

This review provides an in-depth exploration of electrospinning techniques employed to produce micro- or nanofibres of biopharmaceuticals using polymeric solutions or melts with high-voltage electricity. Distinct from prior reviews, the current work narrows its focus on the recent developments and advanced applications in biopharmaceutical formulations. It begins with an overview of electrospinning principles, covering both solution and melt modes. Various methods for incorporating biopharmaceuticals into electrospun fibres, such as surface adsorption, blending, emulsion, co-axial, and high-throughput electrospinning, are elaborated. The review also surveys a wide array of biopharmaceuticals formulated through electrospinning, thereby identifying both opportunities and challenges in this emerging field. Moreover, it outlines the analytical techniques for characterizing electrospun fibres and discusses the legal and regulatory requirements for their production. This work aims to offer valuable insights into the evolving realm of electrospun biopharmaceutical delivery systems.

Factors affecting the preparation of nanocrystals: characterization, surface modifications and toxicity aspects

INTRODUCTION

The fabrication of well-defined nanocrystals in size and form is the focus of much investigation. In this work, we have critically reviewed several recent instances from the literature that shows how the production procedure affects the physicochemical properties of the nanocrystals.

AREAS COVERED

Scopus, MedLine, PubMed, Web of Science, and Google Scholar were searched for peer-review articles published in the past few years using different key words. Authors chose relevant publications from their files for this review. This review focuses on the range of techniques available for producing nanocrystals. We draw attention to several recent instances demonstrating the impact of various process and formulation variables that affect the nanocrystals' physicochemical properties. Moreover, various developments in the characterization techniques explored for nanocrystals concerning their size, morphology, etc. have been discussed. Last but not least, recent applications, the effect of surface modifications, and the toxicological traits of nanocrystals have also been reviewed.

EXPERT OPINION

The selection of an appropriate production method for the formation of nanocrystals, together with a deep understanding of the relationship between the drug's physicochemical properties, unique features of the various formulation alternatives, and anticipated in-vivo performance, would significantly reduce the risk of failure during human clinical trials that are inadequate.

Pharmaceutical amorphous solid dispersion: A review of manufacturing strategies

Amorphous solid dispersions (ASDs) are popular for enhancing the solubility and bioavailability of poorly water-soluble drugs. Various approaches have been employed to produce ASDs and novel techniques are emerging. This review provides an updated overview of manufacturing techniques for preparing ASDs. As physical stability is a critical quality attribute for ASD, the impact of formulation, equipment, and process variables, together with the downstream processing on physical stability of ASDs have been discussed. Selection strategies are proposed to identify suitable manufacturing methods, which may aid in the development of ASDs with satisfactory physical stability.

Co-amorphous formation of piroxicam-citric acid to generate supersaturation and improve skin permeation

The objective of this study was to prepare a co-amorphous formulation of piroxicam (PIR), a non-steroidal anti-inflammatory drug, and citric acid (CA), and evaluate its skin permeation ability. A spray-drying method was employed to prepare the co-amorphous formulation and its physical properties were characterized. X-ray powder diffraction and thermal analysis confirmed a homogeneous amorphous state, and the infrared spectra revealed intermolecular interactions between PIR and CA, suggesting formation of a co-amorphous formulation of PIR and CA. The PIR-CA co-amorphous formulation exhibited no crystallization for 60 days at 4/25/40°C with silica gel. The PIR-CA co-amorphous formulation increased the solubility of PIR in polyethylene glycol 400 compared with that of the pure drug, and physical mixture (PM) of PIR and CA, confirming a supersaturated state in the formulation. The PIR-CA co-amorphous formulation demonstrated higher skin permeation than PIR alone or PM of PIR and CA, and the flux value was consistent with the degree of saturation. Thus, the increase in the skin permeation of PIR from the PIR-CA co-amorphous formulation directly depended on the increased thermodynamic activity by supersaturation in the absence of interactions between the drug and co-former in the vehicle.

Exploring the Complexity of Processing-Induced Dehydration during Hot Melt Extrusion Using In-Line Raman Spectroscopy

The specific aim in this study was to understand the effect of critical process parameters on the solid form composition of model drug compounds during hot melt extrusion using in-line Raman spectroscopy combined with Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS) modeling for semi-quantitative kinetic profiling. It was observed that the hydrate and anhydrate solid forms of two model drugs in the melts of nitrofurantoin (NF):polyethylene oxide (PEO) and piroxicam (PRX):PEO could be resolved from a MCR-ALS model without an external calibration dataset. Based on this model, the influence of two critical process parameters (shear and temperature) on the solid form composition could be evaluated in a real-time mode and the kinetics of complex transformation pathways could be explored. Additionally, the dehydration pathways of NF monohydrate and PRX monohydrate in molten PEO could be derived. It can be concluded that dehydration of both hydrates in PEO occurs via competing mechanisms—a solution-mediated transformation pathway and a solid–solid transformation, and that the balance between these mechanisms is determined by the combined effect of both temperature and shear. Another important observation was that the water released from these hydrate compounds has a detectable effect on the rheological characteristics of this mixture.

The role of S-bond in tenoxicam keto–enolic tautomerization

A non-covalent interaction between the sulphur atom of thiophenyl moiety and oxygen of the carbonyl group (S-bond) plays a crucial role in keto–enol tautomerization of tenoxicam leading to the crystallization of latter only in zwitterionic (ZWC) and not in β-keto–enolic (BKE) form.

Smart systems for determination of drug's solubility

The solubility of drugs is a crucial physicochemical property in the drug discovery or development process and for improving the bioavailability of drugs. There are various methods for evaluating the solubility of drugs including manual measurement methods, mathematical methods, and smart methods. Manual measurement and mathematical methods have some defects which make the smart systems more reliable and important in this field. In this review, various instruments used for the solubility determination, along with the smart systems, have been discussed. Mechanism and applications of each method have been elaborated in detail. Moreover, unique characteristics as well as some limitations of discussed methods are also described.

In-Line UV-Vis Spectroscopy as a Fast-Working Process Analytical Technology (PAT) during Early Phase Product Development Using Hot Melt Extrusion (HME)

This paper displays the potential of an in-line PAT system for early phase product development during pharmaceutical continuous manufacturing following a Quality by Design (QbD) framework. Hot melt extrusion (HME) is used as continuous manufacturing process and UV⁻Vis spectroscopy as an in-line monitoring system. A sequential design of experiments (DoE) (screening, optimisation and verification) was used to gain process understanding for the manufacture of piroxicam (PRX)/Kollidon® VA64 amorphous solid dispersions. The influence of die temperature, screw speed, solid feed rate and PRX concentration on the critical quality attributes (CQAs) absorbance and lightness of color (L*) of the extrudates was investigated using multivariate tools. Statistical analysis results show interaction effects between concentration and temperature on absorbance and L* values. Solid feed rate has a significant effect on absorbance only and screw speed showed least impact on both responses for the screening design. The optimum HME process conditions were confirmed by 4 independent studies to be 20% w/w of PRX, temperature 140 °C, screw speed 200 rpm and feed rate 6 g/min. The in-line UV-Vis system was used to assess the solubility of PRX in Kollidon® VA64 by measuring absorbance and L* values from 230 to 700 nm. Oversaturation was observed for PRX concentrations higher than 20% w/w. Oversaturation can be readily identified as it causes scattering in the visible range. This is observed by a shift of the baseline in the visible part of the spectrum. Extrudate samples were analyzed for degradation using off-line High-Performance Liquid Chromatography (HPLC) standard methods. Results from off-line experiments using differential scanning calorimetry (DSC), and X-ray diffraction (XRD) are also presented.

Supercritical carbon dioxide-based technologies for the production of drug nanoparticles/nanocrystals - A comprehensive review

Low drug bioavailability, which is mostly a result of poor aqueous drug solubilities and of inadequate drug dissolution rates, is one of the most significant challenges that pharmaceutical companies are currently facing, since this may limit the therapeutic efficacy of marketed drugs, or even result in the discard of potential highly effective drug candidates during developmental stages. Two of the main approaches that have been implemented in recent years to overcome poor drug solubility/dissolution issues have frequently involved drug particle size reduction (i.e., micronization/nanonization) and/or the modification of some of the physicochemical and structural properties of poorly water soluble drugs. A large number of particle engineering methodologies have been developed, tested, and applied in the synthesis and control of particle size/particle-size distributions, crystallinities, and polymorphic purities of drug micro- and nano-particles/crystals. In recent years pharmaceutical processing using supercritical fluids (SCF), in general, and supercritical carbon dioxide (scCO₂), in particular, have attracted a great attention from the pharmaceutical industry. This is mostly due to the several well-known advantageous technical features of these processes, as well as to other increasingly important subjects for the pharmaceutical industry, namely their "green", sustainable, safe and "environmentally-friendly" intrinsic characteristics. In this work, it is presented a comprehensive state-of-the-art review on scCO₂-based processes focused on the formation and on the control of the physicochemical, structural and morphological properties of amorphous/crystalline pure drug nanoparticles. It is presented and discussed the most relevant scCO₂, scCO₂-based fluids and drug physicochemical properties that are pertinent for the development of successful pharmaceutical products, namely those that are critical in the selection of an adequate scCO₂-based method to produce pure drug nanoparticles/nanocrystals. scCO₂-based nanoparticle formation methodologies are classified in three main families, and in terms of the most important role played by scCO₂ in particle formation processes: as a solvent; as an antisolvent or a co-antisolvent; and as a "high mobility" additive (a solute, a co-solute, or a co-solvent). Specific particle formation methods belonging to each one of these families are presented, discussed and compared. Some selected amorphous/crystalline drug nanoparticles that were prepared by these methods are compiled and presented, namely those studied in the last 10-15 years. A special emphasis is given to the formation of drug cocrystals. It is also discussed the fundamental knowledge and the main mechanisms in which the scCO₂-based particle formation methods rely on, as well as the current status and urgent needs in terms of reliable experimental data and of robust modeling approaches. Other addressed and discussed topics include the currently available and the most adequate physicochemical, morphological and biological characterization methods required for pure drug nanoparticles/nanocrystals, some of the current nanometrology and regulatory issues associated to the use of these methods, as well as some scale-up, post-processing and pharmaceutical regulatory subjects related to the industrial implementation of these scCO₂-based processes. Finally, it is also discussed the current status of these techniques, as well as their future major perspectives and opportunities for industrial implementation in the upcoming years.

Prediction of Phase Behavior of Spray-Dried Amorphous Solid Dispersions: Assessment of Thermodynamic Models, Standard Screening Methods and a Novel Atomization Screening Device with Regard to Prediction Accuracy

The evaluation of drug–polymer miscibility in the early phase of drug development is essential to ensure successful amorphous solid dispersion (ASD) manufacturing. This work investigates the comparison of thermodynamic models, conventional experimental screening methods (solvent casting, quench cooling), and a novel atomization screening device based on their ability to predict drug–polymer miscibility, solid state properties (T_g value and width), and adequate polymer selection during the development of spray-dried amorphous solid dispersions (SDASDs). Binary ASDs of four drugs and seven polymers were produced at 20:80, 40:60, 60:40, and 80:20 (w/w). Samples were systematically analyzed using modulated differential scanning calorimetry (mDSC) and X-ray powder diffraction (XRPD). Principal component analysis (PCA) was used to qualitatively assess the predictability of screening methods with regards to SDASD development. Poor correlation was found between theoretical models and experimentally-obtained results. Additionally, the limited ability of usual screening methods to predict the miscibility of SDASDs did not guarantee the appropriate selection of lead excipient for the manufacturing of robust SDASDs. Contrary to standard approaches, our novel screening device allowed the selection of optimal polymer and drug loading and established insight into the final properties and performance of SDASDs at an early stage, therefore enabling the optimization of the scaled-up late-stage development.

Selective preparation of elusive and alternative single component polymorphic solid forms through multi-component crystallisation routes

A transferable, simple, method for producing previously elusive and novel polymorphic forms of important active pharmaceutical ingredients (APIs; paracetamol (acetaminophen), piroxicam and piracetam) is demonstrated. Nitrogen heterocyclic co-molecules are employed to influence the self-assembly crystallisation process in a multi-component environment. Previously unknown solvates have also been synthesised by this method.

Recent progress of structural study of polymorphic pharmaceutical drugs

This review considers advances in the understanding of active pharmaceutical ingredient polymorphism since around 2010 mainly from a structural view point, with a focus on twelve model drugs. New polymorphs of most of these drugs have been identified despite that the polymorphism of these old drugs has been extensively studied so far. In addition to the conventional modifications of preparative solvents, temperatures, and pressure, more strategic structure-based methods have successfully yielded new polymorphs. The development of analytical techniques, including X-ray analyses, spectroscopy, and microscopy has facilitated the identification of unknown crystal structures and also the discovery of new polymorphs. Computational simulations have played an important role in explaining and predicting the stability order of polymorphs. Furthermore, these make significant contributions to the design of new polymorphs by considering structure and energy. The new technologies and insights discussed in this review will contribute to the control of polymorphic forms, both during manufacture and in the drug formulation.

Development of Oromucosal Dosage Forms by Combining Electrospinning and Inkjet Printing

Printing technology has been shown to enable flexible fabrication of solid dosage forms for personalized drug therapy. Several methods can be applied for tailoring the properties of the printed pharmaceuticals. In this study, the use of electrospun fibrous substrates in the fabrication of inkjet-printed dosage forms was investigated. A single-drug formulation with lidocaine hydrochloride (LH) and a combination drug system containing LH and piroxicam (PRX) for oromucosal administration were prepared. The LH was deposited on the electrospun and cross-linked gelatin substrates by inkjet printing, whereas PRX was incorporated within the substrate fibers during electrospinning. The solid state analysis of the electrospun substrates showed that PRX was in an amorphous state within the fibers. Furthermore, the results indicated the entrapment and solidification of the dissolved LH within the fibrous gelatin matrix. The printed drug amount (2-3 mg) was in good correlation with the theoretical dose calculated based on the printing parameters. However, a noticeable degradation of the printed LH was detected after a few months. An immediate release (over 85% drug release after 8 min) of both drugs from the printed dosage forms was observed. In conclusion, the prepared electrospun gelatin scaffolds were shown to be suitable substrates for inkjet printing of oromucosal formulations. The combination of electrospinning and inkjet printing allowed the preparation of a dual drug system.

Two pseudo-enantiomeric forms of N-benzyl-4-hydroxy-1-methyl-2,2-dioxo-1H-2λ(6),1-benzothiazine-3-carboxamide and their analgesic properties

The fact that molecular crystals exist as different polymorphic modifications and the identification of as many polymorphs as possible are important considerations for the pharmaceutic industry. The molecule of N-benzyl-4-hydroxy-1-methyl-2,2-dioxo-1H-2λ(6),1-benzothiazine-3-carboxamide, C17H16N2O4S, does not contain a stereogenic atom, but intramolecular hydrogen-bonding interactions engender enantiomeric chiral conformations as a labile racemic mixture. The title compound crystallized in a solvent-dependent single chiral conformation within one of two conformationally polymorphic P212121 orthorhombic chiral crystals (denoted forms A and B). Each of these pseudo-enantiomorphic crystals contains one of two pseudo-enantiomeric diastereomers. Form A was obtained from methylene chloride and form B can be crystallized from N,N-dimethylformamide, ethanol, ethyl acetate or xylene. Pharmacological studies with solid-particulate suspensions have shown that crystalline form A exhibits an almost fourfold higher antinociceptive activity compared to form B.

Experimental electron densities of neutral and zwitterionic forms of the drug piroxicam

The electron and electrostatic properties of piroxicam (PX) were derived from high resolution X-ray diffraction experiments carried out at 100 K.

Controlled release of drugs in electrosprayed nanoparticles for bone tissue engineering

Generating porous topographic substrates, by mimicking the native extracellular matrix (ECM) to promote the regeneration of damaged bone tissues, is a challenging process. Generally, scaffolds developed for bone tissue regeneration support bone cell growth and induce bone-forming cells by natural proteins and growth factors. Limitations are often associated with these approaches such as improper scaffold stability, and insufficient cell adhesion, proliferation, differentiation, and mineralization with less growth factor expression. Therefore, the use of engineered nanoparticles has been rapidly increasing in bone tissue engineering (BTE) applications. The electrospray technique is advantageous over other conventional methods as it generates nanomaterials of particle sizes in the micro/nanoscale range. The size and charge of the particles are controlled by regulating the polymer solution flow rate and electric voltage. The unique properties of nanoparticles such as large surface area-to-volume ratio, small size, and higher reactivity make them promising candidates in the field of biomedical engineering. These nanomaterials are extensively used as therapeutic agents and for drug delivery, mimicking ECM, and restoring and improving the functions of damaged organs. The controlled and sustained release of encapsulated drugs, proteins, vaccines, growth factors, cells, and nucleotides from nanoparticles has been well developed in nanomedicine. This review provides an insight into the preparation of nanoparticles by electrospraying technique and illustrates the use of nanoparticles in drug delivery for promoting bone tissue regeneration.

Four solid forms of tauroursodeoxycholic acid and solid-state transformations: effects of temperature and milling

TUDCA solid forms were characterized. Temperature-triggered and mechanical activated solid-state transformation, as environmental-friendly methods, were successfully used for getting new solid forms and studying solid-state transformations procedure.

Crystallization and disorder of the polytypic α1 and α2 polymorphs of piroxicam

The polytypic α₁ and α₂ polymorphs of piroxicam are described and it is shown that they can be crystallized controllably.

Tautomeric transformations of piroxicam in solution: a combined experimental and theoretical study

Piroxicam tautomerism was studied in solution. Enol-amide tautomer is presented mainly as a sandwich type dimer in ethanol and DMSO. The addition of water leads to gradual shift of the equilibrium towards the zwitterionic tautomer.