Solvent influence on manufacturability, phase behavior and morphology of amorphous solid dispersions prepared via bead coating

Stability Challenges of Amorphous Solid Dispersions of Drugs: A Critical Review on Mechanistic Aspects

The most common drawback of the existing and novel drug molecules is their low bioavailability because of their low solubility. One of the most important approaches to enhance the bioavailability in the enteral route for poorly hydrophilic molecules is amorphous solid dispersion (ASD). The solubility of compounds in amorphous form is comparatively high because of the availability of free energy produced during formulation. This free energy results in the change of crystalline nature of the prepared ASD to the stable crystalline form leading to the reduced solubility of the product. Due to the intrinsic chemical and physical uncertainty and the restricted knowledge about the interactions of active molecules with the carriers making, this ASD is a challenging task. This review focused on strategies to stabilize ASD by considering the various theories explaining the free-energy concept, physical interactions, and thermal properties. This review also highlighted molecular modeling and machine learning computational advancement to stabilize ASD.

Gaining Insight into the Role of the Solvent during Spray Drying of Amorphous Solid Dispersions by Studying Evaporation Kinetics

Spray drying is one of the most commonly used manufacturing techniques for amorphous solid dispersions (ASDs). During spray drying, very fast solvent evaporation is enabled by the generation of small droplets and exposure of these droplets to a heated drying gas. This fast solvent evaporation leads to an increased viscosity that enables kinetic trapping of an active pharmaceutical ingredient (API) in a polymer matrix, which is favorable for the formulation of supersaturated, kinetically stabilized ASDs. In this work, the relation between the solvent evaporation rate and the kinetic stabilization of highly drug-loaded ASDs was investigated. Accordingly, thermal gravimetric analysis (TGA) was employed to study the evaporation kinetics of seven organic solvents and the influence of solutes, i.e., poly(vinylpyrrolidone-co-vinyl acetate) (PVPVA), fenofibrate (FNB), and naproxen (NAP), on the evaporation behavior. At 10 °C below the boiling point of the respective solvent, methanol (MeOH) had the lowest evaporation rate and dichloromethane (DCM) had the highest. PVPVA decreased the evaporation rate for all solvents, yet this effect was more pronounced for the relatively faster evaporating solvents. The APIs had opposite effects on the evaporation process: FNB increased the evaporation rate, while NAP decreased it. The latter might indicate the presence of interactions between NAP and the solvent or NAP and PVPVA, which was further investigated using Fourier transform-InfraRed (FT-IR) spectroscopy. Based on these findings, spray drying process parameters were adapted to alter the evaporation rate. Increasing the evaporation rate of MeOH and DCM enabled the kinetic stabilization of higher drug loadings of FNB, while the opposite trend was observed for ASDs of NAP. Even when higher drug loadings could be kinetically stabilized by adapting the process parameters, the improvement was limited, demonstrating that the phase behavior of these ASDs of FNB and NAP immediately after preparation was predominantly determined by the API-polymer-solvent combination rather than the process parameters applied.

The Value of Bead Coating in the Manufacturing of Amorphous Solid Dispersions: A Comparative Evaluation with Spray Drying

Despite the fact that an amorphous solid dispersion (ASD)-coated pellet formulation offers potential advantages regarding the minimization of physical stability issues, there is still a lack of in-depth understanding of the bead coating process and its value in relation to spray drying. Therefore, bead coating and spray drying were both evaluated for their ability to manufacture high drug-loaded ASDs and for their ability to generate physically stable formulations. For this purpose, naproxen (NAP)–poly(vinyl-pyrrolidone-co-vinyl acetate) (PVP-VA) was selected as an interacting drug–polymer model system, whilst naproxen methyl ester (NAPME)–PVP-VA served as a non-interacting model system. The solvent employed in this study was methanol (MeOH). First, a crystallization tendency study revealed the rapid crystallization behavior of both model drugs. In the next step, ASDs were manufactured with bead coating as well as with spray drying and for each technique the highest possible drug load that still results in an amorphous system was defined via a drug loading screening approach. Bead coating showed greater ability to manufacture high drug-loaded ASDs as compared to spray drying, with a rather small difference for the interacting drug–polymer model system studied but with a remarkable difference for the non-interacting system. In addition, the importance of drug–polymer interactions in achieving high drug loadings is demonstrated. Finally, ASDs coated onto pellets were found to be more physically stable in comparison to the spray dried formulations, strengthening the value of bead coating for ASD manufacturing purposes.