A sensitivity-controlled hydrogen peroxide sensor based on self-assembled Prussian Blue modified electrode

A novel uric acid biosensor based on regular Prussian blue nanocrystal/ upright graphene oxide array nanocomposites

Objective:

Regular Prussian blue nanocrystals (RPB) were grown upright on graphene oxide flakes (GO), which were on the surface of a custom screen-printed carbon electrode (SPCE), using a spray method assisted by a constant magnetic field (CMF).

Method:

After immobilizing uricase, the uric acid biosensor Uricase/RPB/CMF-GO/SPCE was obtained. The detection range of the sensor response to UA was 0.005~2.525 mM, and the detection limit was as low as 3.6 μM. The cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) results showed that compared to amorphous electrodeposited Prussian blue (EDPB), RPB more favorably accelerated electron transport.

Result:

This novel uric acid biosensor exhibits high sensitivity over, a wide concentration range, strong anti- interference ability, and good stability and reproducibility.

Conclusion:

Thus, it has good application prospects for determining uric acid in physiological samples

Current Innovations of Metal Hexacyanoferrates-Based Nanocomposites toward Electrochemical Sensing: Materials Selection and Synthesis Methods

Mixed valence transition metal hexacyanoferrates (MeHCF)-Prussian blue and its analogs receive enormous research interest in the electrochemical sensing field. In recent years, conducting materials such as conducting polymer, carbon nanomaterial, and noble metals have been used to form nanocomposites with MeHCF. The scope of this review offers the reasons behind the preparation of various MeHCF based nanocomposite toward electrochemical detection. We primarily focus on the current progress of the development of MEHCF-based nanocomposites. The synthesis methods for these nanocomposites are also reviewed and discussed.

Facile synthesis of Mn3[Co(CN)6]2·nH2O nanocrystals for high-performance electrochemical energy storage devices

Mn₃[Co(CN)₆]₂·nH₂O nanocrystals are firstly applied in flexible solid-state electrochemical energy storage devices.

Facile synthesis of Prussian blue nanocubes/silver nanowires network as a water-based ink for the direct screen-printed flexible biosensor chips

The large-scale fabrication of nanocomposite based biosensors is always a challenge in the technology commercialization from laboratory to industry. In order to address this issue, we have designed a facile chemical method of fabricated nanocomposite ink applied to the screen-printed biosensor chip. This ink can be derived in the water through the in-situ growth of Prussian blue nanocubes (PBNCs) on the silver nanowires (AgNWs) to construct a composite nanostructure by a facile chemical method. Then a miniature flexible biosensor chip was screen-printed by using the prepared nanocomposite ink. Due to the synergic effects of the large specific surface area, high conductivity and electrocatalytic activity from AgNWs and PBNCs, the as-prepared biosensor chip exhibited a fast response (<3s)， a wider linear response from 0.01 to 1.3mM with an ultralow LOD=5µm, and the ultrahigh sensitivities of 131.31 and 481.20µAmM^-1cm^-2 for the detections of glucose and hydrogen peroxide (H₂O₂), respectively. Furthermore, the biosensor chip exhibited excellent stability, good reproducibility and high anti-interference ability towards physiological substances under a very low working potential of -0.05. Hence, the proposed biosensor chip also showed a promising potential for the application in practical analysis.

Multi-tasking Schiff base ligand: a new concept of AuNPs synthesis

Multi-tasking 3,4-dihydroxysalophen Schiff base tetradentate ligand (3,4-DHS) as reductant, stabilizer, and catalyst in a new concept of gold nanoparticles (AuNPs) synthesis is demonstrated. 3,4-DHS is able to reduce HAuCl4 in water, acting also as capping agent for the generation of stable colloidal suspensions of Schiff base ligand-AuNPs assemblies of controlled size by providing a robust coating to AuNPs, within a unique reaction step. Once deposited on carbon electrodes, 3,4-DHS-AuNPs assemblies show a potent electrocatalytic effect towards hydrazine oxidation and hydrogen peroxide oxidation/reduction.

Uniform manganese hexacyanoferrate hydrate nanocubes featuring superior performance for low-cost supercapacitors and nonenzymatic electrochemical sensors

Uniform manganese hexacyanoferrate hydrate nanocubes are prepared via a simple chemical precipitation method at room temperature. Due to both micro/mesopores of the Prussian blue analogue and nanocubic structures, the manganese hexacyanoferrate hydrate nanocubes allow the efficient charge transfer and mass transport for electrolyte solution and chemical species. Thus, the manganese hexacyanoferrate hydrate nanocube electrode shows a good rate capability and cycling stability for electrochemical capacitors. Furthermore, electrodes modified with manganese hexacyanoferrate hydrate nanocubes demonstrate a sensitive electrochemical response to hydrogen peroxide (H2O2) in buffer solutions with a high selectivity.

Fabrication of TiN nanostructure as a hydrogen peroxide sensor by oblique angle deposition

Nanostructured titanium nitride (TiN) films with varying porosity were prepared by the oblique angle deposition technique (OAD). The porosity of films increases as the deposition angle becomes larger. The film obtained at an incident angle of 85° exhibits the best catalytic activity and sensitivity to hydrogen peroxide (H2O2). This could be attributed to its largest contact area with the electrolyte. An effective approach is thus proposed to fabricate TiN nanostructure as H2O2 sensor by OAD.

Glucose biosensor based on titanium dioxide-multiwall carbon nanotubes-chitosan composite and functionalized gold nanoparticles

In this paper, a new glucose biosensor was prepared. At first, Prussian blue (PB) was electrodeposited on a glassy carbon electrode (GCE) modified by titanium dioxide-multiwall carbon nanotubes-chitosan (TiO(2)-MWNTs-CS) composite, and then gold nanoparticles functionalized by poly(diallyldimethylammonium chloride) (PDDA-Au) were adsorbed on the PB film. Finally, the negatively charged glucose oxidase (GOD) was self-assembled on to the positively charged PDDA-Au. The electrochemical performances of the modified electrodes had been studied by cyclic voltammetry (CV) and amperometric methods, respectively. In addition, the stepwise fabrication process of the as-prepared biosensor was characterized by scanning electron microscopy. PDDA-Au nanoparticles were characterized by ultraviolet-vis absorption spectroscopy and transmission electron microscopy. Under the optimal conditions, the as-prepared biosensor exhibited a good response performance to glucose with a linear range from 6 μM to 1.2 mM with a detection limit of 0.1 μM glucose (S/N = 3). In addition, this work indicated that TiO(2)-MWNTs-CS composite and PDDA-Au nanoparticles held great potential for constructing biosensors.

Potential of a simple lab-on-a-tube for point-of-care measurements of multiple analytes

This technical note presents a simple and disposable lab-on-a-tube (LOT) for point-of-care measurements of multiple analytes. LOT is a one-step device that can perform both sample collection and multi-sensing on-site. Sample collection is conducted by taking advantage of its inherent micro/macro channel structure while multi-sensing is conducted by integrated microsensors. This approach ensures reliable transportation of various samples into the testing area by either passive capillary force or active suction force, thus avoiding the need for a pump or injection components as used in lab-on-a-chip systems. The developed LOT (Diameter = 1 mm, Sensing length = 4.5 mm, Required sample volume = 3.5 microl) is capable of simultaneously quantifying the concentrations of glucose, lactate and oxygen in human serum samples. The result suggests the LOT hold great potential for many point-of-care applications.