Electrochemical determination of nitrite based on poly(amidoamine) dendrimer-modified carbon nanotubes for nitrite oxidation

A violet light-emitting diode-based gas-phase molecular absorption device for measurement of nitrate and nitrite in environmental water

A simple and sensitive device for the detection of nitrite and nitrate in environmental waters was developed based on visible light gas-phase molecular absorption spectrometry. By integrating a detection cell (DC), semiconductor refrigeration temperature-controlling system (SRTCY), and nitrite reactor into a sequential injection analysis system, trace levels of nitrite and nitrate in complex matrices were successfully measured. A low energy-consuming light-emitting diode (violet, 400-405 nm) was coupled with a visible light-to-voltage converter (TSL257) to measure the gas-phase molecular absorption. To reduce the interference of water vapor, an SRTCY was used to condense the water vapor on-line before the gas-phase analyte entered the DC. The DC was radiatively heated by the SRTCY to avoid water vapor condensation in the light path. As a result, the obtained baseline noise reduced 3.75 times than that of without SRTCY. Under the optimized conditions, the device achieved limits of detection (3σ/k) of 0.055 and 0.36 mmol/L (0.77 and 5.04 mg N/L) for nitrite and nitrate, respectively, and the linear calibration ranges were 0.1-15 mmol/L (R2 = 0.9946) and 1-10 mmol/L (R2 = 0.9995), respectively. Precisions of 5.2 % and 9.0 % were achieved for ten successive determinations of 0.3 mmol/L nitrite and 1.0 mmol/L nitrate, and the analytical times for nitrite and nitrate determination were 5 and 13 min, respectively. This method was validated against standard methods and recovery tests, and it was applied to the measurement of nitrite and nitrate in environmental waters. Moreover, a device was designed to enable the field measurement of nitrite and nitrate in complex matrices.

Ratiometric Colorimetric Detection of Nitrite Realized by Stringing Nanozyme Catalysis and Diazotization Together

Due to the great threat posed by excessive nitrite in food and drinking water to human health, it calls for developing reliable, convenient, and low-cost methods for nitrite detection. Herein, we string nanozyme catalysis and diazotization together and develop a ratiometric colorimetric approach for sensing nitrite in food. First, hollow MnFeO (a mixture of Mn and Fe oxides with different oxidation states) derived from a Mn-Fe Prussian blue analogue is explored as an oxidase mimic with high efficiency in catalyzing the colorless 3,3′,5,5′-tetramethylbenzidine (TMB) oxidation to blue TMBox, presenting a notable signal at 652 nm. Then, nitrite is able to trigger the diazotization of the product TMBox, not only decreasing the signal at 652 nm but also producing a new signal at 445 nm. Thus, the analyte-induced reverse changes of the two signals enable us to establish a ratiometric colorimetric assay for nitrite analysis. According to the above strategy, facile determination of nitrite in the range of 3.3–133.3 μM with good specificity was realized, providing a detection limit down to 0.2 μM. Compared with conventional single-signal analysis, our dual-signal ratiometric colorimetric mode was demonstrated to offer higher sensitivity, a lower detection limit, and better anti-interference ability against external detection environments. Practical applications of the approach in examining nitrite in food matrices were also verified.

Improved spectrophotometric method for nitrite determination in processed foods and dietary exposure assessment for Korean children and adolescents

A spectrophotometric method based on diazo-coupling reaction for nitrite analysis was established and validated, including inter-laboratory validation, linearity, accuracy, precision, the limit of detection (LOD) and limit of quantification (LOQ). The time-saving and high-recovery method was established by examining the filtration step, colorimetric process and concentration range of the calibration curve. This method showed good linearity (r² > 0.999) in the range of 0.025-1.0 μg/mL. The three-level recoveries were between 86.7% and 108.6%, with the coefficient of variation (CV) below 5.8%. Mean nitrite concentration ranges in processed foods were ND-33.47 mg/kg. The mean nitrite intake was 0.8% of the Acceptable Daily Intake (ADI, 0.07 mg/kg bw/day) for all children and adolescents and 2.8% for the consumer group. The major contributors for all subjects and consumers were ham, sausage and bacon. These results indicated that the improved method was suitable for analyzing nitrite in processed foods and the nitrite exposure levels were safe.

Phenosafranin-Based Colorimetric-Sensing Platform for Nitrite Detection Enabled by Griess Assay

A facile and effective colorimetric-sensing platform based on the diazotization of phenosafranin for the detection of NO 2 - under acidic conditions using the Griess assay is presented. Diazotization of commercial phenosafranin produces a color change from purplish to blue, which enables colorimetric quantitative detection of NO 2 - . Optimal detection conditions were obtained at a phenosafranin concentration of 0.25 mM, HCl concentration of 0.4 M, and reaction time of 20 min. Under the optimized detection conditions, an excellent linearity range from 0 to 20 μM was obtained with a detection limit of 0.22 μM. Favorable reproducibility and selectivity of the colorimetric sensing platform toward NO 2 - were also verified. In addition, testing spiked ham sausage, bacon, and sprouts samples demonstrated its excellent practicability. The presented colorimetric sensing platform is a promising candidate for the detection of NO 2 - in real applications.

Nitrogen-Doped Carbon Quantum Dots as Fluorescent Probes for Sensitive and Selective Detection of Nitrite

Nitrites are the upstream precursors of the carcinogenic nitrosamines, which are widely found in the natural environment and many food products. It is important to develop a simple and sensitive sensor for detecting nitrites. In this work, a fluorescence probe based on nitrogen-doped carbon quantum dots (N-CQDs) was developed for the sensitive and selective determination of nitrites. At pH 2, the fluorescence of N-CQDs can be selectively quenched by nitrite due to the fact N-nitroso compounds can be formed in the reaction of amide groups with nitrous acid, which results in fluorescence static quenching. Under optimal conditions, fluorescence intensity quenching upon addition of nitrite gives a satisfactory linear relationship covering the linear range of 0.2-20 μM, and the limit of detection (LOD) is 40 nM. Moreover, this method has been successfully applied to the determination of nitrites in tap water, which indicates its great potential for monitoring of nitrites in environmental samples.

Environmentally friendly synthesis of CeO2 nanoparticles for the catalytic oxidation of benzyl alcohol to benzaldehyde and selective detection of nitrite

Cerium oxide nanoparticles (CeO₂ NPs) are favorable in nanotechnology based on some remarkable properties. In this study, the crystalline CeO₂ NPs are successfully prepared by an efficient microwave combustion (MCM) and conventional route sol-gel (CRSGM) methods. The structural morphology of the as-prepared CeO₂ NPs was investigated by various spectroscopic and analytical techniques. Moreover, the XRD pattern confirmed the formation of CeO₂ NPs as a face centered cubic structure. The magnetometer studies indicated the low saturation magnetization (23.96 emu/g) of CeO₂ NPs for weak paramagnetic and high saturation magnetization (32.13 emu/g) of CeO₂ NPs for super paramagnetic. After that, the oxidation effect of benzyl alcohol was investigated which reveals good conversion and selectivity. Besides, the CeO₂ NPs modified glassy carbon electrode (GCE) used for the detection of nitrite with linear concentration range (0.02–1200 μM), low limit of detection (0.21 μM) and higher sensitivity (1.7238 μAμM⁻¹ cm⁻²). However, the CeO₂ NPs modified electrode has the fast response, high sensitivity and good selectivity. In addition, the fabricated electrode is applied for the determination of nitrite in various water samples. Eventually, the CeO₂ NPs can be regarded as an effective way to enhance the catalytic activity towards the benzyl alcohol and nitrite.

Methods for the detection and determination of nitrite and nitrate: A review

Various techniques for the determination of nitrite and/or nitrate developed during the past 15 years were reviewed in this article. 169 references were covered. The detection principles and analytical parameters such as matrix, detection limits and detection range of each method were tabulated. The advantages and disadvantages of various methods were evaluated. In comparison to other methods, spectrofluorimetric methods have become more attractive due to its facility availability, high sensitivity and selectivity, low limits of detection and low-cost.

Bare and boron-doped cubic silicon carbide nanowires for electrochemical detection of nitrite sensitively

Fabrication of eletrochemical sensors based on wide bandgap compound semiconductors has attracted increasing interest in recent years. Here we report for the first time electrochemical nitrite sensors based on cubic silicon carbide (SiC) nanowires (NWs) with smooth surface and boron-doped cubic SiC NWs with fin-like structure. Multiple techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and electron energy loss spectroscopy (EELS) were used to characterize SiC and boron-doped SiC NWs. As for the electrochemical behavior of both SiC NWs electrode, the cyclic voltammetric results show that both SiC electrodes exhibit wide potential window and excellent electrocatalytic activity toward nitrite oxidation. Differential pulse voltammetry (DPV) determination reveals that there exists a good linear relationship between the oxidation peak current and the concentration in the range of 50-15000 μmoL L(-1) (cubic SiC NWs) and 5-8000 μmoL L(-1) (B-doped cubic SiC NWs) with the detection limitation of 5 and 0.5 μmoL L(-1) respectively. Compared with previously reported results, both as-prepared nitrite sensors exhibit wider linear response range with comparable high sensitivity, high stability and reproducibility.

Hydrophobicity effects in iron polypyridyl complex electrocatalysis within Nafion thin-film electrodes

Four polypyridyl redox catalysts Fe(bp)₃²⁺, Fe(ph)₃²⁺, Fe(dm)₃²⁺, and Fe(tm)₃²⁺ (with bp, ph, dm, and tm representing 2,2′-bipyridine, 1,10-phenanthroline, 4,4′-dimethyl-2,2′-bipyridine, and 3,4,7,8-tetramethyl-1,10-phenanthroline, respectively) are investigated for the electrocatalytic oxidation of three analytes (nitrite, arsenite, and isoniazid).

PdCo alloy nanoparticle-embedded carbon nanofiber for ultrasensitive nonenzymatic detection of hydrogen peroxide and nitrite

PdCo alloy nanoparticle-embedded carbon nanofiber (PdCo/CNF) prepared by electrospinning and thermal treatment was employed as a high-performance platform for the determination of hydrogen peroxide and nitrite. The as-obtained PdCo/CNF were characterized by transmission electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction. Electrochemical impedance spectroscopy, cyclic voltammetry and differential pulse voltammetry were employed to investigate the electrochemical behaviors of the resultant biosensor. The proposed PdCo/CNF-based biosensor showed excellent analytical performances toward hydrogen peroxide (detection limit: 0.1 μM; linear range: 0.2 μM-23.5 mM) and nitrite (detection limit: 0.2 μM; linear range: 0.4-30 μM and 30-400 μM). The superior analytical properties could be attributed to the synergic effect and firmly embedment of well-dispersed PdCo alloy nanoparticles. These attractive electrochemical properties make this robust electrode material promising for the development of effective electrochemical sensors.

Large mesoporous carbons decorated with silver and gold nanoparticles by a self-assembly method: enhanced electrocatalytic activity for H2O2 electroreduction and sodium nitrite electrooxidation

The silver, gold nanoparticles were grown onto poly (diallyldimethyl ammoniumchloride, PDDA)-functionalized large mesoporous carbon (LMC) by simple self-assembly method. AuNPs or AgNPs/PDDA–LMC show superior electrocatalytic activity.

Dendrimer-encapsulated copper as a novel oligonucleotides label for sensitive electrochemical stripping detection of DNA hybridization

This paper describes the synthesis and characterization of a novel electrochemical label for sensitive electrochemical stripping detection of DNA hybridization based on dendrimer-encapsulated copper. The generation 4.5 (G 4.5) carboxyl-terminated poly(amidoamine) dendrimer with a trimesyl core was used as a template for synthesis of Cu²⁺/dendrimer nanocomposites (Cu-DNCs). Ratios of Cu²⁺/dendrimer were optimized in order to obtain stable nanocomposites with maximal copper loading in the interior of a polymeric shell. Cu-DNCs labeled DNA probe was employed for determining a target ssDNA immobilized on multi-walled carbon nanotubes-modified glassy carbon electrode (GCE) based on a specific hybridization reaction. The hybridization events were monitored by electrochemical detection of Cu anchored on the hybrids after the release in a diluted nitric acid by anodic stripping differential pulse voltammetry (ASDPV). The results showed that only a complementary sequence could form a dsDNA with the Cu-DNCs DNA probe and give an obvious electrochemical signal. The non-complementary sequence exhibited negligible signal change compared with the blank measurement (means: the electrode containing no target DNA incubating in hybridization buffer solution containing Cu-DNCs DNA probe for a certain time). The use of Cu encapsulated-dendrimer as tags and ASDPV for the detection of the released Cu ions could enhance the hybridization signal, and result in the increase of the sensitivity for the target DNA. Under the conditions employed here, the detection limit for measuring the full complementary sequence is down to pM level.

The new age of carbon nanotubes: an updated review of functionalized carbon nanotubes in electrochemical sensors

Since the discovery of carbon nanotubes (CNTs), they have drawn considerable research attention and have shown great potential application in many fields due to their unique structural, mechanical, and electronic properties. However, their native insolubility severely holds back the process of application. In order to overcome this disadvantage and broaden the scope of their application, chemical functionalization of CNTs has attracted great interest over the past several decades and produced various novel hybrid materials with specific applications. Notably, the rapid development of functionalized CNTs used as electrochemical sensors has been successfully witnessed. In this featured article, the recent progress of electrochemical sensors based on functionalized CNTs is discussed and classified according to modifiers covering organic (oxygen functional groups, small organic molecules, polymers, DNA, protein, etc.), inorganic (metal nanoparticles, metal oxide, etc.) and organic-inorganic hybrids. By employing some representative examples, it will be demonstrated that functionalized CNTs as templates, carriers, immobilizers and transducers are promising for the construction of electrochemical sensors.

Voltammetric Study of the Copper Pentacyanonitrosylferrate Adsorbed on the Silica Modified with a Poly(propylene)imine Hexadecylamine Dendrimer for Determination of Nitrite

Poly(propylene)imine hexadecylamine dendrimer (DAB-Am-16) was anchored on the surface of 3-chloropropylsilyl silica gel and subsequently interacted with copper nitroprusside. The composite was characterized by infrared (FTIR), energy dispersive X-ray (EDX), and cyclic voltammetry. The above techniques confirmed the successful anchoring of the dendrimer on the silica gel modified surface and its interaction with copper nitroprusside. The cyclic voltammogram of CuNPSD was found to exhibit two redox couples with (Eθ′)1= 0.30 V and (Eθ′)2= 0.78 V versus Ag/AgCl ( mol L−1;  mV s−1) attributed to the redox processes and , respectively. The CuNPSD-modified graphite paste electrode was found to show a linear response of to  mol L−1for nitrite determination with a detection limit (DL) of  mol L−1and an amperometric sensitivity of 25.0 mA/mol L−1. The CuNPSD-modified graphite paste electrode was found to show a good electrochemical stability and an excellent response to the electrocatalytic oxidation of sodium nitrite.

Facile synthesis of flower like copper oxide and their application to hydrogen peroxide and nitrite sensing

BACKGROUND

The detection of hydrogen peroxide (H2O2) and nitrite ion (NO2-) is of great important in various fields including clinic, food, pharmaceutical and environmental analyses. Compared with many methods that have been developed for the determination of them, the electrochemical detection method has attracted much attention. In recent years, with the development of nanotechnology, many kinds of micro/nano-scale materials have been used in the construction of electrochemical biosensors because of their unique and particular properties. Among these catalysts, copper oxide (CuO), as a well known p-type semiconductor, has gained increasing attention not only for its unique properties but also for its applications in many fields such as gas sensors, photocatalyst and electrochemistry sensors. Continuing our previous investigations on transition-metal oxide including cuprous oxide and α-Fe2O3 modified electrode, in the present paper we examine the electrochemical and electrocatalytical behavior of flower like copper oxide modified glass carbon electrodes (CuO/GCE).

RESULTS

Flower like copper oxide (CuO) composed of many nanoflake was synthesized by a simple hydrothermal reaction and characterized using field-emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD). CuO modified glass carbon electrode (CuO/GCE) was fabricated and characterized electrochemically. A highly sensitive method for the rapid amperometric detection of hydrogen peroxide (H2O2) and nitrite (NO2-) was reported.

CONCLUSIONS

Due to the large specific surface area and inner characteristic of the flower like CuO, the resulting electrode show excellent electrocatalytic reduction for H2O2 and oxidation of NO2-. Its sensitivity, low detection limit, fast response time and simplicity are satisfactory. Furthermore, this synthetic approach can also be applied for the synthesis of other inorganic oxides with improved performances and they can also be extended to construct other micro/nano-structured functional surfaces.

Surface modification of carbon nanotubes with dendrimers or hyperbranched polymers

The different methods for modification of carbon nanotubes with dendrimers or hyperbranched polymers are summarized, and recent development is highlighted by discussing some representative examples in detail.

Advances in carbon nanotube based electrochemical sensors for bioanalytical applications

Electrochemical (EC) sensing approaches have exploited the use of carbon nanotubes (CNTs) as electrode materials owing to their unique structures and properties to provide strong electrocatalytic activity with minimal surface fouling. Nanofabrication and device integration technologies have emerged along with significant advances in the synthesis, purification, conjugation and biofunctionalization of CNTs. Such combined efforts have contributed towards the rapid development of CNT-based sensors for a plethora of important analytes with improved detection sensitivity and selectivity. The use of CNTs opens an opportunity for the direct electron transfer between the enzyme and the active electrode area. Of particular interest are also excellent electrocatalytic activities of CNTs on the redox reaction of hydrogen peroxide and nicotinamide adenine dinucleotide, two major by-products of enzymatic reactions. This excellent electrocatalysis holds a promising future for the simple design and implementation of on-site biosensors for oxidases and dehydrogenases with enhanced selectivity. To date, the use of an anti-interference layer or an artificial electron mediator is critically needed to circumvent unwanted endogenous electroactive species. Such interfering species are effectively suppressed by using CNT based electrodes since the oxidation of NADH, thiols, hydrogen peroxide, etc. by CNTs can be performed at low potentials. Nevertheless, the major future challenges for the development of CNT-EC sensors include miniaturization, optimization and simplification of the procedure for fabricating CNT based electrodes with minimal non-specific binding, high sensitivity and rapid response followed by their extensive validation using "real world" samples. A high resistance to electrode fouling and selectivity are the two key pending issues for the application of CNT-based biosensors in clinical chemistry, food quality and control, waste water treatment and bioprocessing.