Electrocatalytic activity of supported gold nanoparticles toward CO oxidation: The perimeter effect of gold–support interface

Small Gold Nanoparticles Interfaced to Electrodes through Molecular Linkers: A Platform to Enhance Electron Transfer and Increase Electrochemically Active Surface Area

For the smallest nanostructures (<5 nm), small changes in structure can lead to significant changes in properties and reactivity. In the case of nanoparticle (NP)-functionalized electrodes, NP structure and composition, and the nature of the NP-electrode interface have a strong influence upon electrochemical properties that are critical in applications such as amperometric sensing, photocatalysis and electrocatalysis. Existing methods to fabricate NP-functionalized electrodes do not allow for precise control over all these variables, especially the NP-electrode interface, making it difficult to understand and predict how structural changes influence NP activity. We investigated the electrochemical properties of small (d_core < 2.5 nm) gold nanoparticles (AuNPs) on boron doped diamond electrodes using three different electrode fabrication techniques with varying degrees of nanoparticle-electrode interface definition. Two methods to attach AuNPs to the electrode through a covalently bound molecular linker were developed and compared to NP-functionalized electrodes fabricated using solution deposition methods (drop-casting and physiadsorption of a monolayer). In each case, a ferrocene redox probe was tethered to the AuNP surface to evaluate electron transfer through the AuNPs. The AuNPs that were molecularly interfaced with the electrode exhibited nearly ideal, reproducible electrochemical behavior with narrow redox peaks and small peak separations, whereas the solution deposited NPs had broader redox peaks with large peak separations. These data suggest that the molecular tether facilitates AuNP-mediated electron transfer. Interestingly, the molecularly tethered NPs also had significantly more electrochemically active surface area than the solution deposited NPs. The enhanced electrochemical behavior of the molecularly interfaced NPs demonstrates the significant influence of the interface on NP-mediated electron transfer and suggests that similar modified electrodes can serve as versatile platforms for studies and applications of nanoparticles.

Iridium Oxide Nanoparticles and Iridium/Iridium Oxide Nanocomposites: Photochemical Fabrication and Application in Catalytic Reduction of 4-Nitrophenol

Hydrous iridium oxide (IrOx) nanoparticles (NPs) with an average diameter of 1.7 ± 0.3 nm were prepared via photochemical hydrolysis of iridium chloride in alkaline medium at room temperature. The photoinduced hydrolysis was monitored by time-dependent ultraviolet-visible (UV-vis) spectroscopy, and the effects of the incident wavelength and irradiation time on the production of IrOx NPs were systematically investigated. It was found that UV-vis irradiation is crucial for the generation of IrOx NPs during the hydrolysis of IrCl3, and once the irradiation was turned off, the hydrolysis reaction stopped immediately. The production rate of IrOx NPs greatly depended on the incident wavelength. There is a critical wavelength of 500 nm for the hydrolysis reaction, and IrOx NPs can only be produced under the illumination with an incident wavelength shorter than 500 nm. Moreover, the shorter the incident wavelength, the faster the growth rate of IrOx NPs. The obtained IrOx NPs were highly stable during two months of storage at 4 °C. The Ir/IrOx nanocomposites were prepared by surface reduction of IrOx NPs with NaBH4. The microstructure of the Ir/IrOx composite was characterized by transmission electron microscopy (TEM), and the presence of zero-valence Ir was confirmed by the X-ray diffraction (XRD) result. The Ir/IrOx nanocomposite exhibited good catalytic activity and high recycling stability toward the reduction of 4-nitrophenol. The catalytic activity per unit surface area of the Ir/IrOx composite catalyst was increased by a factor of 15 compared to that of pure Ir catalyst. The presence of the Ir/IrOx interfaces in the composite catalyst is believed to be responsible for the high activity.

RF-sputtering preparation of gold-nanoparticle-modified ITO electrodes for electrocatalytic applications

The preparation of gold-nanoparticle (AuNPs)-modified indium tin oxide (ITO) electrodes (AuNPs/ITO) was performed by radio-frequency (RF) sputtering from Ar plasmas at temperatures as low as 60 °C, tailoring the AuNP morphology and content as a function of the sole sputtering time. The latter parameter was varied from 5 to 20 min in order to investigate the influence of gold amount and distribution on the electrochemical performances of the resulting AuNPs/ITO systems. The electrodes were characterized using field emission-scanning electron microscopy (FE-SEM), UV-vis absorption and x-ray photoelectron spectroscopies (XPS); moreover variable scan rate cyclic voltammetry (CV) studies were performed to examine their electrochemical behavior. The electrocatalytic activity of the nanostructured AuNPs/ITO electrodes toward methanol oxidation was investigated and compared with a continuous gold film (Aufilm/ITO). The catalytic efficiency of the AuNPs/ITO systems was found to increase with the gold content and the AuNPs-support boundary region in the corresponding samples. For the longest sputtering time (i.e. 20 min) the performances of the nanostructured electrode were better than the Aufilm/ITO reference, despite the much lower catalyst amount. Furthermore, conversely from the AuNPs/ITO samples, in the Au(film)/ITO case the gold film displayed a poor adhesion to the substrate and the electrode could be used only for a limited number of electrochemical cycles.