Template-free electrodeposition of tellurium nanostructures in a room-temperature ionic liquid

Electroless deposition of tellurium nanowires in eutectic solvents using immobilised silver islands

In this work we demonstrate a new approach towards the electroless deposition of tellurium nanowires in deep eutectic solvents. Unlike most electroless deposition where the substrate is sacrificed to drive the reduction, our process uses immobilised silver epoxy islands on gold films to give localised galvanic displacement of the silver, resulting in an even growth of wires across the entire gold electrode surface. We demonstrate the strong dependence of the nanostructure on the experimental conditions, with changes in bath temperature, tellurium concentration and the halide component of the solvent leading to sizeable alterations in the nanowire geometry. This demonstrates electroless deposition as a promising synthetic route towards low-dimensional tellurium nanostructures.

An Effective Strategy for Template-Free Electrodeposition of Aluminum Nanowires with Highly Controllable Irregular Morphologies

Aluminum nanowires with irregular morphologies were prepared by template-free electrodeposition from a room-temperature chloroaluminate ionic liquid. The effects of the diffusion condition and deposition potential on the morphologies of Al nanowires were investigated. The decrease of diffusion flux leads to the formation of particular segmented morphologies of Al nanowires. A dynamic equilibrium between the electrochemical reaction and the diffusion of Al₂Cl₇⁻ results in the current fluctuation and the periodical variation of diameters in the Al nanowires growth period. Al nanowires with several kinds of morphologies can be controllably electrodeposited under a restricted diffusion condition, without using a template. Increasing the overpotential shows the similar influence on the morphology of Al nanowires as the decrease in diffusion flux under the restricted diffusion condition. Most of the segmented Al nanowires have a single crystalline structure and grow in the [100] orientation. This work also provides a new strategy for the fabrication of nanowires with highly controllable irregular morphologies.

Potential Application of Ionic Liquids for Electrodeposition of the Material Targets for Production of Diagnostic Radioisotopes

An overview of the reported electrochemistry studies on the chemistry of the element for targets for isotope production in ionic liquids (ILs) is provided. The majority of investigations have been dedicated to two aspects of the reactive element chemistry. The first part of this review presents description of the cyclotron targets properties, especially physicochemical characterization of irradiated elements. The second part is devoted to description of the electrodeposition procedures leading to obtain elements or their alloys coatings (e.g., nickel, uranium) as the targets for cyclotron and reactor generation of the radioisotopes. This review provides an evaluation of the role ILs can have in the production of isotopes.

Template-free electrodeposition of AlFe alloy nanowires from a room-temperature ionic liquid as an anode material for Li-ion batteries

AlFe alloy nanowires were directly electrodeposited on copper substrates from trimethylamine hydrochloride (TMHC)–AlCl₃ ionic liquids with small amounts of FeCl₃ at room temperature without templates. Coin cells composed of AlFe alloy nanowire electrodes and lithium foils were assembled to characterize the alloy electrochemical properties by galvanostatic charge/discharge tests. Effects of FeCl₃ concentration, potential and temperature on the alloy morphology, composition and cyclic performance were examined. Addition of Fe into the alloy changed the nanowires from a ‘hill-like’ bulk morphology to a free-standing morphology, and increased the coverage area of the alloy on Cu substrates. As an inactive element, Fe could also buffer the alloys' large volume changes during Li intercalation and deintercalation. AlFe alloy nanowires composed of a small amount of Fe with an average diameter of 140 nm exhibited an outstanding cyclic performance and delivered a specific capacity of about 570 mA h g⁻¹ after 50 cycles. This advanced template-free method for the direct preparation of high performance nanostructure AlFe alloy anode materials is quite simple and inexpensive, which presents a promising prospect for practical application in Li-ion batteries.

Electrodeposition in Ionic Liquids

Due to their attractive physico-chemical properties, ionic liquids (ILs) are increasingly used as deposition electrolytes. This review summarizes recent advances in electrodeposition in ILs and focuses on its similarities and differences with that in aqueous solutions. The electrodeposition in ILs is divided into direct and template-assisted deposition. We detail the direct deposition of metals, alloys and semiconductors in five types of ILs, including halometallate ILs, air- and water-stable ILs, deep eutectic solvents (DESs), ILs with metal-containing cations, and protic ILs. Template-assisted deposition of nanostructures and macroporous structures in ILs is also presented. The effects of modulating factors such as deposition conditions (current density, current density mode, deposition time, temperature) and electrolyte components (cation, anion, metal salts, additives, water content) on the morphology, compositions, microstructures and properties of the prepared materials are highlighted.

Fabrication of NiTe films by transformed electrodeposited Te thin films on Ni foils and their electrical properties

Tellurium (Te) source of compact nickel telluride (NiTe) thin film was prepared by simple electrochemical deposition method.