A one-step, clean, capping-agent-free electrochemical approach to prepare Pt nanoparticles with preferential (100) orientation and their high electrocatalytic activities

Synthesis of catalytically active bimetallic nanoparticles within solution-processable metal–organic-framework scaffolds

Bimetallic alloy nanoparticles are synthesized by in situ reduction of mixed metal ions inside CD-MOFs.

The Microstructure and Pitting Resistance of 2002 Lean Duplex Stainless Steel after the Simulated Welding Thermal Cycle Process

In this paper, thermal cycles with different heat inputs and cooling rates were investigated for a novel lean duplex stainless steel 2002 using a welding simulation. The microstructure and pitting resistance of the simulated heat-affected zones were studied. With the increasing heat input, the amount and size of the austenite phase both increased, along with a transformation from rods to dendritic structures. The critical pitting temperature (CPT) and the pitting potential (E_pit) both increased first and then declined as the heat input increased, indicating a strong dependence of pitting resistance on the heat input. For the different cooling rates, the amount of ferrite increased as the cooling rate increased from 0.25 °C/s to 20 °C/s. The CPT and E_pit both increased with the increasing cooling rates, indicating an improved pitting resistance. The pits initiated preferentially at the boundaries of ferrite and austenite due to the precipitation of M₂₃C₆ in the specimens with different cooling rates.

Pt Monolayers on Electrodeposited Nanoparticles of Different Compositions for Ammonia Electro-Oxidation

Pt monolayers (PtML) supported on nanoparticles with different compositions (i.e., Ru, Rh, Pd, Ir, and Au) were synthesized by the surface–limited redox replacement of underpotentially deposited Cu monolayers on nanoparticle supports. Nanoparticle supports with different compositions were directly deposited on the conducting substrate by a clean and one-step electrodeposition method with controlled deposition potential and time. The whole synthesis process of the electrode was free of surfactants, binders, capping agents and reductants, and without an additional coating process of electrocatalysts. The results show that the specific activity (SA) of PtML electrocatalysts depended strongly on the composition of the nanoparticle support. For example, the PtML supported on the Au nanoparticle exhibited 8.3 times higher SA than that supported on the Ru and Pd nanoparticles. The change in the SA of the PtML supported on different nanoparticles was related to the substrate–induced strain in the PtML resulting from the lattice mismatch between the PtML and the nanoparticle support. As the strain in the PtML changed from the tensile strain to the compressive strain, the SA of the PtML electrocatalysts decreased remarkably.

Size- and Density-Controllable Fabrication of the Platinum Nanoparticle/ITO Electrode by Pulse Potential Electrodeposition for Ammonia Oxidation

Pulse potential electrodeposition was successfully utilized to electrochemically fabricate platinum (Pt) nanoparticles on indium tin oxide (ITO) conductive glass substrates for catalysis toward ammonia electro-oxidation. The effect of deposition parameters (lower potential E_l, lower potential duration t_l, and upper potential duration t_u) on the size and number density of Pt nanoparticles was investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrocatalytic activity of the Pt nanoparticle/ITO electrode for ammonia oxidation was characterized by the cyclic voltammetry (CV) method. The results showed that lower E_l and longer t_l accelerate the formation of Pt nuclei while longer t_u favors the growth of grain size to some extent, as E_l mainly tunes electrochemical overpotential while t_l and t_u affect the activation and mass transfer process. By the tuning of the deposition parameters, Pt nanoparticle/ITO electrodes with a polycrystalline nature and 5 nm-scale primary particles, could be easily modified in Pt particle size and number density. Furthermore, the Pt nanoparticle/ITO electrode shows high mass specific catalytic activity (MA) toward ammonia oxidation (1.65 mC μg^-1), much higher than that of the commercial Pt/C electrode (0.32 mC μg^-1). Additionally, the high catalytic performance results not only from the nanosize effect of Pt nanoparticles, but also from the special morphology formed during the electrodeposition process.

Synthesis of Cubic-Shaped Pt Particles with (100) Preferential Orientation by a Quick, One-Step and Clean Electrochemical Method

A new approach has been developed for in situ preparing cubic-shaped Pt particles with (100) preferential orientation on the surface of the conductive support by using a quick, one-step, and clean electrochemical method with periodic square-wave potential. The whole electrochemical deposition process is very quick (only 6 min is required to produce cubic Pt particles), without the use of particular capping agents. The shape and the surface structure of deposited Pt particles can be controlled by the lower and upper potential limits of the square-wave potential. For a frequency of 5 Hz and an upper potential limit of 1.0 V (vs saturated calomel electrode), as the lower potential limit decreases to the H adsorption potential region, the Pt deposits are changed from nearly spherical particles to cubic-shaped (100)-oriented Pt particles. High-resolution transmission electron microscopy and selected-area electron diffraction reveal that the formed cubic Pt particles are single-crystalline and enclosed by (100) facets. Cubic Pt particles exhibit characteristic H adsorption/desorption peaks corresponding to the (100) preferential orientation. Ge irreversible adsorption indicates that the fraction of wide Pt(100) surface domains is 47.8%. The electrocatalytic activities of different Pt particles are investigated by ammonia electro-oxidation, which is particularly sensitive to the amount of Pt(100) sites, especially larger (100) domains. The specific activity of cubic Pt particles is 3.6 times as high as that of polycrystalline spherical Pt particles, again confirming the (100) preferential orientation of Pt cubes. The formation of cubic-shaped Pt particles is related with the preferential electrochemical deposition and dissolution processes of Pt, which are coupled with the periodic desorption and adsorption processes of O-containing species and H adatoms.

The design of Fe, N-doped hierarchically porous carbons as highly active and durable electrocatalysts for a Zn–air battery

A new type of Fe, N-doped hierarchically porous carbons (N–Fe-HPCs) has been synthesized via a green and simple silicate templated two-step graphitization of N-enriched polyquaternium networks.