Electroreduction of oxygen on Vulcan carbon supported Pd nanoparticles and Pd–M nanoalloys in acid and alkaline solutions

Tuning the Structure of Pd@Ni-Co Nanowires and Their Electrochemical Properties

One-dimensional transition metal materials are promising supports for precious metals used in energy production processes. Due to their electrochemical properties, 3d-group metals (such as Ni, Co, and Fe) can actively interact with catalysts by a strong metal-support interaction. This study shows that changing the Ni:Co ratio makes it possible to modulate the structure of the catalyst supports, which, in turn, provides a tool for designing their electrical and electrochemical properties. For example, Ni1-Co9 shows the highest electrical conductivity (5.8-10-4 S/cm) among all of the materials examined. On the contrary, the Pd@Ni7-Co3 system presents the highest mass activity (>2000 mA mg-1) at 0.7 V, exceeding by several times that of commercial Pt/C (>300 mA mg-1) at the same potential. Our study opens the gateway for applications of bimetallic transition metal nanowires in catalytic conversion and energy production processes.

Electrochemical Metal Recycling: Recovery of Palladium from Solution and In Situ Fabrication of Palladium-Carbon Catalysts via Impact Electrochemistry

Recycling of critical materials, regeneration of waste, and responsible catalyst manufacture have been repeatedly documented as essential for a sustainable future with respect to the environment and energy production. Electrochemical methods have become increasingly recognized as capable of achieving these goals, and “impact” electrochemistry, with the advantages associated with dynamic nanoelectrodes, has recently emerged as a prime candidate for the recovery of metals from solution. In this report, the nanoimpact technique is used to generate carbon-supported palladium catalysts from low-concentration palladium(II) chloride solutions (i.e., a waste stream mimic) as a proof of concept. Subsequently, the catalytic properties of this material in both synthesis (Suzuki coupling reaction) and electrocatalysis (hydrogen evolution) are demonstrated. Transient reductive impact signals are shown and analyzed at potentials negative of +0.4 V (vs SCE) corresponding to the onset of palladium deposition in traditional voltammetry. Direct evidence of Pd modification was obtained through characterization by environmental scanning electron microscopy/energy-dispersive X-ray spectroscopy, inductively coupled plasma mass spectrometry, X-ray photoelectron spectroscopy, transmission electron microscopy, and thermogravimetric analysis of impacted particles. This showed the formation of deposits of Pd0 partially covering the 50 nm carbon black particles with approximately 14% Pd (wt %) under the conditions used. This material was then used to demonstrate the conversion of iodobenzene into its biphenyl product (confirmed through nuclear magnetic resonance) and the successful production of hydrogen as an electrocatalyst under acidic conditions (under cyclic voltammetry).

Effect of Pd on the Electrocatalytic Activity of Pt towards Oxidation of Ethanol in Alkaline Solutions

The understanding of electrocatalytic activity and poisoning resistance properties of Pt and Pd nanoparticles, recognized as the best electrocatalysts for the ethanol oxidation reaction, is an essential step for the commercialization of direct ethanol fuel cells (DEFCs). In this paper, mono and bimetallic Pt and Pd nanoparticles with different atomic ratios have been synthesized to study their electrocatalytic properties for an ethanol oxidation reaction in alkaline solutions. The different nanoparticles were physiochemically characterized by transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The electrochemical characterization was performed by cyclic voltammetry and chronoamperometry measurements. The electrochemical measurements indicate that Pt nanoparticles have much higher electrocatalytic activity for ethanol oxidation than Pd nanoparticles. The studies with bimetallic PtPd nanoparticles showed a significant impact of their composition on the ethanol oxidation. Thus, the highest electrocatalytic activity and poisoning resistance properties were obtained for Pt3Pd2 nanoparticles. Moreover, this study demonstrates that the poisoning of the catalyst surface through ethanol oxidation is related to the prevalence of the acetaldehyde–acetate route and the polymerization of acetaldehyde through aldol condensation in the alkaline media.

Selective Electrocatalytic H2 O2 Generation by Cobalt@N-Doped Graphitic Carbon Core-Shell Nanohybrids

Electrocatalytic oxygen reduction (ORR) is an emerging synthetic strategy to prepare H₂ O₂ in a sustainable fashion. N-doped graphitic carbon with embedded cobalt nanoparticles was selected as an advanced material able to selectively trigger the ORR to form H₂ O₂ with a faradaic efficiency of almost 100 % at very positive applied potentials. The production of H₂ O₂ proceeded with high rates as calculated by bulk electrolysis (49 mmol g^-1  h^-1 ) and excellent current densities (≈-0.8 mA cm^-2 at 0.5 V vs. reversible hydrogen electrode). The totally selective behavior depended on the combination of concomitant material features, such as the textural properties, the nature of the metal, the distribution of N moieties, the acidic environment, and the applied potential.

Investigation of Supported Pd-Based Electrocatalysts for the Oxygen Reduction Reaction: Performance, Durability and Methanol Tolerance

Next generation cathode catalysts for direct methanol fuel cells (DMFCs) must have high catalytic activity for the oxygen reduction reaction (ORR), a lower cost than benchmark Pt catalysts, and high stability and high tolerance to permeated methanol. In this study, palladium catalysts supported on titanium suboxides (Pd/Ti_nO_2n–1) were prepared by the sulphite complex route. The aim was to improve methanol tolerance and lower the cost associated with the noble metal while enhancing the stability through the use of titanium-based support; 30% Pd/Ketjenblack (Pd/KB) and 30% Pd/Vulcan (Pd/Vul) were also synthesized for comparison, using the same methodology. The catalysts were ex-situ characterized by physico-chemical analysis and investigated for the ORR to evaluate their activity, stability, and methanol tolerance properties. The Pd/KB catalyst showed the highest activity towards the ORR in perchloric acid solution. All Pd-based catalysts showed suitable tolerance to methanol poisoning, leading to higher ORR activity than a benchmark Pt/C catalyst in the presence of low methanol concentration. Among them, the Pd/Ti_nO_2n–1 catalyst showed a very promising stability compared to carbon-supported Pd samples in an accelerated degradation test of 1000 potential cycles. These results indicate good perspectives for the application of Pd/Ti_nO_2n–1 catalysts in DMFC cathodes.

One-pot green synthesis of reduced graphene oxide (RGO)/Fe3O4 nanocomposites and its catalytic activity toward methylene blue dye degradation

The reduced graphene oxide (RGO)/Fe3O4 nanocomposites were synthesized through a facile one-pot green synthesis by using solanum trilobatum extract as a reducing agent. Spherical shaped Fe3O4 nanoparticles with the diameter of 18 nm were uniformly anchored over the RGO matrix and the existence of fcc structured Fe3O4 nanoparticles over the RGO matrix was ensured from X-ray diffraction patterns. The amide functional groups exist in the solanum trilobatum extract is directly responsible for the reduction of Fe(3+) ions and GO. The thermal stability of GO was increased by the removal of hydrophilic functional groups via solanum trilobatum extract and was further promoted by the ceramic Fe3O4 nanoparticles. The ID/IG ratio of RGO/Fe3O4 was increased over GO, indicating the extended number of structural defects and disorders in the RGO/Fe3O4 composite. The catalytic efficiency of prepared nanostructures toward methylene blue (MB) dye degradation mediated through the electron transfer process of BH4(-) ions was studied in detail. The π-π stacking, hydrogen bonding and electrostatic interaction exerted between the RGO/Fe3O4 composite and methylene blue, increased the adsorption efficiency of dye molecules and the large surface area and extended number of active sites completely degraded the MB dye within 12 min.

The role of surface oxygenated-species and adsorbed hydrogen in the oxygen reduction reaction (ORR) mechanism and product selectivity on Pd-based catalysts in acid media

Surface adsorbed species can significantly alter the catalytic activity and product selectivity.

Gold-promoted structurally ordered intermetallic palladium cobalt nanoparticles for the oxygen reduction reaction

Considerable efforts to make palladium and palladium alloys active catalysts and a possible replacement for platinum have had a marginal success. Here we report on a structurally ordered Au10Pd₄₀Co₅₀ catalyst that exhibits comparable activity to conventional platinum catalysts in both acid and alkaline media. Electron microscopic techniques demonstrate that, at elevated temperatures, palladium cobalt nanoparticles undergo an atomic structural transition from core-shell to a rare intermetallic ordered structure with twin boundaries forming stable {111}, {110} and {100} facets via addition of gold atoms. The superior stability of this catalyst compared with platinum after 10,000 potential cycles in alkaline media is attributed to the atomic structural order of PdCo nanoparticles along with protective effect of clusters of gold atoms on the surface. This strategy of making ordered palladium intermetallic alloy nanoparticles can be used in diverse heterogeneous catalysis where particle size and structural stability matter.

Enhanced methanol oxidation and oxygen reduction reactions on palladium-decorated FeCo@Fe/C core-shell nanocatalysts in alkaline medium

Palladium based nano-alloys are well known for their unique electrocatalytic properties. In this work, a palladium-decorated FeCo@Fe/C core-shell nanocatalyst has been prepared by a new method called microwave-induced top-down nanostructuring and decoration (MITNAD). This simple, yet efficient technique, resulted in the generation of sub-10 nm sized FeCo@Fe@Pd nanocatalysts (mainly 3-5 nm) from a micron-sized (0.21-1.5 μm) FeCo@Fe/C. The electrocatalytic activities of the core-shell nanocatalysts were explored for methanol oxidation reaction (MOR) and oxygen reduction reaction (ORR) in alkaline medium. A negative shift of 300 mV in the onset potential for MOR was observed, with a current thrice that of the Pd/C catalysts. A very low resistance to electron transfer (Rct) was observed while the ratio of forward-to-backward oxidation current (If/Ib) was doubled. The overpotential of ORR was significantly reduced with a positive shift of about 250 mV and twice the reduction current density was observed in comparison with Pd/C nanocatalysts with the same mass loading. The kinetic parameters (in terms of the Tafel slope (b) = -59.7 mV dec(-1) (Temkin isotherm) and high exchange current density (jo) = 1.26 × 10(-2) mA cm(-2)) provide insights into the favorable electrocatalytic performance of the catalysts in ORR in alkaline media. Importantly, the core-shell nanocatalyst exhibited excellent resistance to possible methanol cross-over during ORR, which shows excellent promise for application in direct alkaline alcohol fuel cells (DAAFCs).