Amphotericin B ion channel mimetic sensor: A new type of potassium-selective sensor based on electrode-supported hybrid bilayer membranes

Electrografting a Hybrid Bilayer Membrane via Diazonium Chemistry for Electrochemical Impedance Spectroscopy of Amyloid-β Aggregation

Herein, a novel hybrid bilayer membrane is introduced as a platform to study the aggregation of amyloid-β1-42 (Aβ1-42) peptide on surfaces. The first layer was covalently attached to a glassy carbon electrode (GCE) via diazonium electrodeposition, which provided a highly stable template for the hybrid bilayer formation. To prepare the long-chain hybrid bilayer membrane (lcHBLM)-modified electrodes, GCE surfaces were modified with 4-dodecylbenzenediazonium (DDAN) followed by the modification with dihexadecyl phosphate (DHP) as the second layer. For the preparation of short-chain hybrid bilayer membrane (scHBLM)-modified electrodes, GCE surfaces were modified with 4-ethyldiazonium (EDAN) as the first layer and bis(2-ethylhexyl) phosphate (BEHP) was utilized as the second layer. X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) were used to characterize the bilayer formation. Both positively charged [Ru(NH3)6]3+ and negatively charged ([Fe(CN)6]3-/4-) redox probes were used for electrochemical characterization of the modified surfaces using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). EIS results showed a decrease in charge transfer resistance (Rct) upon incubation of Aβ1-42 on the hybrid bilayer-modified surfaces. This framework provides a promising electrochemical platform for designing hybrid bilayers with various physicochemical properties to study the interaction of membrane-bound receptors and biomolecules on surfaces.

Introduction to Microelectrode Arrays, the Site-Selective Functionalization of Electrode Surfaces, and the Real-Time Detection of Binding Events

Microelectrode arrays have great potential as analytical tools because currents can be independently measured at each electrode in the array. In principle, these currents can be monitored in order to follow in real time the binding events that occur between the members of a molecular library and a biological target. To capitalize on this potential, the surface of the array must be selectively functionalized so that each unique member of the molecular library is associated with a unique individually addressable electrode or set of electrodes in the array. To this end, this instructional review summarizes methods for coating the arrays with porous polymers that allow for the attachment of molecules to the surface of the array, selectively conducting reactions at individual electrodes in the array, characterizing molecules that are placed on the arrays, and running the analytical experiments needed to monitor in real time binding events between molecules on the array and a biological target.

Microelectrode Arrays and the Use of PEG-Functionalized Diblock Copolymer Coatings

PEG-modified diblock copolymer surfaces have been examined for their compatibility with microelectrode array based analytical methods. The use of PEG-modified polymer surfaces on the arrays was initially problematic because the redox couples used in the experiments were adsorbed by the polymer. This led the current measured by cyclic voltammetry for the redox couple to be unstable and increase with time. However, two key findings allow the experiments to be successful. First, after multiple cyclic voltammograms the current associated with the redox couple does stabilize so that a good baseline current can be established. Second, the rate at which the current stabilizes is consistent every time a particular coated array is used. Hence, multiple analytical experiments can be conducted on an array coated with a PEG-modified diblock copolymer and the data obtained is comparable as long as the data for each experiment is collected at a consistent time point.

Microelectrode arrays: a general strategy for using oxidation reactions to site selectively modify electrode surfaces

Oxidation reactions are powerful tools for synthesis because they allow for the functionalization of molecules. Here, we present a general method for conducting these reactions on a microelectrode array in a site-selective fashion. The reactions are run as a competition between generation of a chemical oxidant at the electrodes in the array and reduction of the oxidant by a "confining agent" in the solution above the array. The "confining agent" does not need to be more reactive than the substrate fixed to the surface of the array. In many cases, the same substrate placed on the surface of the array can also be used in solution as the confining agent.

Site-selective chemistry and the attachment of peptides to the surface of a microelectrode array

Peptides have been site-selectively placed on microelectrode arrays with the use of both thiol-based conjugate additions and Cu(I)-coupling reactions between thiols and aryl halides. The conjugate addition reactions used both acrylate and maleimide Michael acceptors. Of the two methods, the Cu(I)-coupling reactions proved far superior because of their irreversibility. Surfaces constructed with the conjugate addition chemistry were not stable at neutral pHs, especially the surface using the maleimide acceptor. Once a peptide was placed onto the array, it could be monitored in "real-time" for its interactions with a biological receptor.