The correlation of electrochemical and fuel cell results for alcohol oxidation in acidic and alkaline media

Stability of Bimetallic PtxRuy - From Model Surfaces to Nanoparticulate Electrocatalysts

Fundamental research campaigns in electrocatalysis often involve the use of model systems, such as single crystals or magnetron-sputtered thin films (single metals or metal alloys). The downsides of these approaches are that oftentimes only a limited number of compositions are picked and tested (guided by chemical intuition) and that the validity of trends is not verified under operating conditions typically present in real devices. These together can lead to deficient conclusions, hampering the direct application of newly discovered systems in real devices. In this contribution, the stability of magnetron-sputtered bimetallic PtxRuy thin film electrocatalysts (0 at. % to 100 at. % Ru content) along with three commercially available carbon-supported counterparts (50-67 at. % Ru content) was mapped under electrocatalytic conditions in acidic electrolytes using online ICP-MS. We found several differences between the two systems in the amount of metals dissolved along with the development of the morphology and composition. While the Pt-rich PtxRuy compositions remained unchanged, 30-50 nm diameter surface pits were detected in the case of the Ru-rich sputtered thin films. Contrastingly, the surface of the carbon-supported NPs enriched in Pt accompanied by the leaching of a significant amount of Ru from the alloy structure was observed. Change in morphology was accompanied by a mass loss reaching around 1-2 wt % in the case of the sputtered samples and almost 10 wt % for the NPs. Since PtxRuy has prime importance in driving alcohol oxidation reactions, the stability of all investigated alloys was screened in the presence of isopropanol. While Pt dissolution was marginally affected by the presence of isopropanol, several times higher Ru dissolution was detected, especially in the case of the Ru-rich compositions. Our results underline that trends in terms of electrocatalytic activity and stability cannot always be transferred from model samples to systems that are closer to the ones applied in real devices.

Bimetallic AgPt Nanoalloys as an Electrocatalyst for Ethanol Oxidation Reaction: Synthesis, Structural Analysis, and Electro-Catalytic Activity

In the present work, the chemical synthesis of AgPt nanoalloys is reported by the polyol method using polyvinylpyrrolidone (PVP) as a surfactant and a heterogeneous nucleation approach. Nanoparticles with different atomic compositions of the Ag and Pt elements (1:1 and 1:3) were synthesized by adjusting the molar ratios of the precursors. The physicochemical and microstructural characterization was initially performed using the UV-Vis technique to determine the presence of nanoparticles in suspension. Then, the morphology, size, and atomic structure were determined using XRD, SEM, and HAADF-STEM techniques, confirming the formation of a well-defined crystalline structure and homogeneous nanoalloy with an average particle size of less than 10 nm. Finally, the cyclic voltammetry technique evaluated the electrochemical activity of bimetallic AgPt nanoparticles supported on Vulcan XC-72 carbon for the ethanol oxidation reaction in an alkaline medium. Chronoamperometry and accelerated electrochemical degradation tests were performed to determine their stability and long-term durability. The synthesized AgPt (1:3)/C electrocatalyst presented significative catalytic activity and superior durability due to the introduction of Ag that weakens the chemisorption of the carbonaceous species. Thus, it could be an attractive candidate for cost-effective ethanol oxidation compared to commercial Pt/C.

Electrochemical Oxidation of Isopropanol on Platinum-Ruthenium Nanoparticles Studied with Real-Time Product and Dissolution Analytics

The selective electrooxidation of 2-propanol to acetone can be used in fuel cells which, when combined with the transfer hydrogenation of acetone from liquid organic hydrogen carriers, will enable the realization of hydrogen economy without using molecular hydrogen gas for storage and transportation. We study the reaction on platinum and platinum-ruthenium nanocatalysts using unique tools for the real-time characterization of reaction and dissolution products. Acetone is the primary product on all investigated catalysts, and only traces of CO₂ form at high potentials. We propose that the reaction occurs on Pt-Ru ensemble sites at low potentials and on Pt-Pt sites at high potentials. Dissolution of surface ruthenium atoms leads to suppression of the process at low overpotential. The main shortcomings to be addressed for an efficient catalyst performance are (a) the narrow potential range in which the bimetallic catalyst is active, (b) the surface poisoning from adsorbed acetone, and (c) the dissolution of ruthenium.

Ethanol Electrooxidation at Platinum-Rare Earth (RE = Ce, Sm, Ho, Dy) Binary Alloys

Proton exchange membrane fuel cells and direct alcohol fuel cells have been extensively studied over the last three decades or so. They have emerged as potential systems to power portable applications, providing clean energy, and offering good commercial viability. Ethanol is considered one of the most interesting fuels in this field. Herein, platinum-rare earth (Pt-RE) binary alloys (RE = Ce, Sm, Ho, Dy, nominal composition 50 at.% Pt) were produced and studied as anodes for ethanol oxidation reaction (EOR) in alkaline medium. A Pt-Dy alloy with nominal composition 40 at.% Pt was also tested. Their electrocatalytic performance was evaluated by voltammetric and chronoamperometric measurements in 2 M NaOH solution with different ethanol concentrations (0.2–0.8 M) in the 25–45 °C temperature range. Several EOR kinetic parameters were determined for the Pt-RE alloys, namely the charge transfer and diffusion coefficients, and the number of exchanged electrons. Charge transfer coefficients ranging from 0.60 to 0.69 and n values as high as 0.7 were obtained for the Pt0.5Sm0.5 electrode. The EOR reaction order at the Pt-RE alloys was found to vary between 0.4 and 0.9. The Pt-RE electrodes displayed superior performance for EOR than bare Pt, with Pt0.5Sm0.5 exhibiting the highest electrocatalytic activity. The improved electrocatalytic activity in all of the evaluated Pt-RE binary alloys suggests a strategy for the solution of the existing anode issues due to the structure-sensitive EOR.

Liquid fuel cells

The advantages of liquid fuel cells (LFCs) over conventional hydrogen-oxygen fuel cells include a higher theoretical energy density and efficiency, a more convenient handling of the streams, and enhanced safety. This review focuses on the use of different types of organic fuels as an anode material for LFCs. An overview of the current state of the art and recent trends in the development of LFC and the challenges of their practical implementation are presented.