A High Power Density Dual-electrolyte Lithium-Silver Battery with Celgard® 2325 Separator

Dual-ion conductors: from liquid to solid

The traditional working principle within lithium-ion batteries relies on Li+ shuttling between the cathode and anode, namely the rocking-chair mechanism. A single working ion constrains the possibilities for battery design and the selection of electrode materials, while realizing multiple working ions offers the potential to break through the fundamental principles of traditional battery construction. Accordingly, it is necessary to develop dual-ion conductors to enable the migration of multiple working ions. This focus article starts by introducing traditional dual-ion batteries based on liquid electrolytes and their pros and cons. Then, solidifying liquid dual-ion conductors is expected to overcome these drawbacks, so the development of solid dual-ion conductors is discussed in detail. Specifically, basic design principles of solid dual-ion conductors are briefly proposed, including constructing continuous ion transport channels and choosing appropriately sized ion carriers. The potential applications of solid dual-ion conductors are also summarized, such as stabilizing the electrode/electrolyte interface and activating additional redox couples. The goal of this article is to inspire researchers in the development of dual-ion conductors and to contribute to the advancement of all-solid-state batteries.

Improved Adhesion of Nafion™-Coated Separator to Water-Processable LiNi0.5Mn1.5O4 Electrodes

The adhesion between electrode and separator is a key feature in cell assembly. Nafion™-coated separators for water-processed LiNi0.5Mn1.5O4 (LNMO) electrodes are here proposed as an alternative to the polyolefin separators. Specifically, polyolefin separators are modified with Nafion™ solutions and their adhesion to high-potential LNMO electrodes is investigated. The physicochemical properties of the Nafion™-coated separator and its electrochemical performance in Li/LNMO cells are discussed and compared to those obtained with polyolefin Celgard® (Charlotte, NC, USA) PP2075 separator. Improved adhesion and cycling stability, which could be further enhanced by a mild lamination process, were demonstrated with a thin layer of Nafion™ (0.1 mg cm−2).

Effects of Polypropylene Orientation on Mechanical and Heat Seal Properties of Polymer-Aluminum-Polymer Composite Films for Pouch Lithium-Ion Batteries

In this study, polyamide-aluminum foil-polypropylene (PA-Al-PP) composite films with different orientation status of the PP layer were prepared, and their morphology, tensile, peeling and heat seal behavior were studied. The comparative study of tensile and fracture behaviors of single-layer film of PA, Al and PP, as well as the composite films of PA-Al, PP-Al and PA-Al-PP revealed that in PA-Al-PP composite film, the PA layer with the highest tensile strength can share the tensile stress from the Al layer during stretching, while the PP layer with the lowest tensile strength can prevent further development of the small cracks on boundary of the Al layer during stretching. Moreover, the study of heat seal behavior suggested that both the orientation status and the heat seal conditions were important factors in determining the heat seal strength (HSS) and failure behavior of the sample. Four failure types were observed, and a clear correspondence between HSS and failure types was found. The results also elucidated that for the composite film, only in the cases where the tensile stress was efficiently released by each layer during HSS measurement could the composite film exhibit desired high HSS that was even higher than its tensile strength.

Rational Integration of Polypropylene/Graphene Oxide/Nafion as Ternary-Layered Separator to Retard the Shuttle of Polysulfides for Lithium-Sulfur Batteries

The reversible electrochemical transformation from lithium (Li) and sulfur (S) into Li2 S through multielectron reactions can be utilized in secondary Li-S batteries with very high energy density. However, both the low Coulombic efficiency and severe capacity degradation limits the full utilization of active sulfur, which hinders the practical applications of Li-S battery system. The present study reports a ternary-layered separator with a macroporous polypropylene (PP) matrix layer, graphene oxide (GO) barrier layer, and Nafion retarding layer as the separator for Li-S batteries with high Coulombic efficiency and superior cyclic stability. In the ternary-layered separator, ultrathin layer of GO (0.0032 mg cm(-2) , estimated to be around 40 layers) blocks the macropores of PP matrix, and a dense ion selective Nafion layer with a very low loading amount of 0.05 mg cm(-2) is attached as a retarding layer to suppress the crossover of sulfur-containing species. The ternary-layered separators are effective in improving the initial capacity and the Coulombic efficiency of Li-S cells from 969 to 1057 mAh g(-1) , and from 80% to over 95% with an LiNO3 -free electrolyte, respectively. The capacity degradation is reduced from 0.34% to 0.18% per cycle within 200 cycles when the PP separator is replaced by the ternary-layered separators. This work provides the rational design strategy for multifunctional separators at cell scale to effective utilizing of active sulfur and retarding of polysulfides, which offers the possibility of high energy density Li-S cells with long cycling life.