Fe-N-C Electrocatalysts for Oxygen Reduction Reaction Synthesized by Using Aniline Salt and Fe 3+ /H 2 O 2 Catalytic System

Molecularly imprinted polydopamine modified with nickel nanoparticles wrapped with carbon: fabrication, characterization and electrochemical detection of uric acid

An electrochemical sensor is described for determination of uric acid (UA). Carbon-enwrapped nickel nanoparticles (Ni@BC) were coated with polydopamine (PDA) that was molecularly imprinted with UA. The biomass carbon (BC) was synthesized by one-step solid-state pyrolysis from leaves of Firmiana platanifolia. The imprinted polymer was obtained by electrodeposition of DA as the monomer. The amount of monomer, the scan cycles, pH value and adsorption time were optimized. Furthermore, the selectivity of the MIP for UA on a glassy carbon electrode (GCE) was evaluated by selectivity tests. The differential pulse voltammetric responses to UA with and without interferents were consistent. The modified GCE has a linear response in the 0.01-30 μM UA concentration range, and the limit of detection is 8 nM. The MIP electrode was applied to the analysis of UA in urine for which the initial concentrations were determined by the phosphotungstic acid kit. Recoveries ranged from 91.3 to 113.4%, with relative standard deviations between 1.3 and 9.7% (n = 3). Graphical abstract Schematic presentation of electrochemical detection of uric acid by molecularly imprinted polydopamine modified with nickel nanoparticles wrapped with carbon (Ni@BC-MIP).

Methanol-Tolerant M–N–C Catalysts for Oxygen Reduction Reactions in Acidic Media and Their Application in Direct Methanol Fuel Cells

Direct methanol fuel cells (DMFCs) are emerging technologies for the electrochemical conversion of the chemical energy of a fuel (methanol) directly into electrical energy, with a low environmental impact and high efficiency. Yet, before this technology can reach a large-scale diffusion, specific issues must be solved, in particular, the high cost of the cell components. In a direct methanol fuel cell system, high capital costs are mainly derived from the use of noble metal catalysts; therefore, the development of low-cost electro-catalysts, satisfying the target requirements of high performance and durability, represents an important challenge. The research is currently addressed to the development of metal–nitrogen–carbon (M–N–C) materials as cheap and sustainable catalysts for the oxygen reduction reaction (ORR) in an acid environment, for application in polymer electrolyte fuel cells fueled by hydrogen or alcohol. In particular, this mini-review summarizes the recent advancements achieved in DMFCs using M–N–C catalysts. The presented analysis is restricted to M–N–C catalysts mounted at the cathode of a DMFC or investigated in rotating disk electrode (RDE) configuration for the ORR in the presence of methanol in order to study alcohol tolerance. The main synthetic routes and characteristics of the catalysts are also presented.

Quantifying the density and utilization of active sites in non-precious metal oxygen electroreduction catalysts

Carbon materials doped with transition metal and nitrogen are highly active, non-precious metal catalysts for the electrochemical conversion of molecular oxygen in fuel cells, metal air batteries, and electrolytic processes. However, accurate measurement of their intrinsic turn-over frequency and active-site density based on metal centres in bulk and surface has remained difficult to date, which has hampered a more rational catalyst design. Here we report a successful quantification of bulk and surface-based active-site density and associated turn-over frequency values of mono- and bimetallic Fe/N-doped carbons using a combination of chemisorption, desorption and ⁵⁷Fe Mössbauer spectroscopy techniques. Our general approach yields an experimental descriptor for the intrinsic activity and the active-site utilization, aiding in the catalyst development process and enabling a previously unachieved level of understanding of reactivity trends owing to a deconvolution of site density and intrinsic activity.

Iron and nitrogen doped carbon materials are widely studied electrocatalysts, however measurement of features such as intrinsic turn-over frequency and active site utilization has proved difficult. Here, the authors use a combination of chemisorption and spectroscopy techniques to determine these properties.