Hydrogen evolution at nanoporous gold/tungsten sulfide composite film and its optimization

Nucleation and growth mechanism of dendrite-free Ni–Cu catalysts by magneto-electrodeposition for the hydrogen evolution reaction

A controllable preparation strategy for high-efficiency Ni–Cu catalysts with specific morphology.

Heterostructures formed through abraded van der Waals materials

To fully exploit van der Waals materials and their vertically stacked heterostructures, new mass-scalable production routes which are low cost but preserve the high electronic and optical quality of the single crystals are required. Here, we demonstrate an approach to realise a variety of functional heterostructures based on van der Waals nanocrystal films produced through the mechanical abrasion of bulk powders. We find significant performance enhancements in abraded heterostructures compared to those fabricated through inkjet printing of nanocrystal dispersions. To highlight the simplicity, applicability and scalability of the device fabrication, we demonstrate a multitude of different functional heterostructures such as resistors, capacitors and photovoltaics. We also demonstrate the creation of energy harvesting devices, such as large area catalytically active coatings for the hydrogen evolution reaction and enhanced triboelectric nanogenerator performance in multilayer films. The ease of device production makes this a promising technological route for up-scalable films and heterostructures.

Low-cost, mass-scalable production routes which preserve the quality of the single crystals are required to up-scale van der Waals materials. Here, the authors demonstrate an approach to realise a variety of functional heterostructures based on van der Waals nanocrystal films produced through the mechanical abrasion of bulk powders.

Electrochemical performance of ruthenium nanoparticles decorated on nitride carbon for non-enzymatic detection of hydrogen peroxide

Development of high-performance Pt-free non-enzymatic hydrogen peroxide (H2O2) sensors on the basis of supported metal nanoparticles (NPs) is important for industrial and biological applications. Here, we report the preparation of ultrafine, surface-clean, and well-distributed Ru NPs and concomitant formation of nitride carbon (Ru/NC) by pyrolyzing tris(2,2'-bipyridyl)ruthenium(ii) chloride (TBRC) with carbon. The use of the nitrogen (N)-containing Ru complex of TBRC as the metal precursor is essential for the preparation of ultrafine and highly dispersed Ru NPs (1.20 nm in diameter) on a NC support. The as-synthesized Ru/NC-800 displays superior analytical performance for non-enzymatic detection of H2O2 with a low detection limit of 0.468 μM, high sensitivity of 698 μA mM-1 cm-2, excellent linear detection ranging from 0.001 to 10.000 mM, good stability, and high selectivity. The control experiment results indicate that the high-performance of Ru/NC-800 must be ascribed to the ultrasmall and highly dispersed Ru NPs and N-doping, which can supply a higher density of active sites available for H2O2 detection. This study provides a facile strategy to synthesize ultrafine metal NPs and for concomitant production of NC for electrocatalytic non-enzymatic sensing.

Mass-producible 2D-WS2 bulk modified screen printed electrodes towards the hydrogen evolution reaction

A screen-printable ink that contained varying percentage mass incorporations of two dimensional tungsten disulphide (2D-WS2) was produced and utilized to fabricate bespoke printed electrodes (2D-WS2-SPEs). These WS2-SPEs were then rigorously tested towards the Hydrogen Evolution Reaction (HER) within an acidic media. The mass incorporation of 2D-WS2 into the 2D-WS2-SPEs was found to critically affect the observed HER catalysis with the larger mass incorporations resulting in more beneficial catalysis. The optimal (largest possible mass of 2D-WS2 incorporation) was the 2D-WS2-SPE40%, which displayed a HER onset potential, Tafel slope value and Turn over Frequency (ToF) of -214 mV (vs. RHE), 51.1 mV dec-1 and 2.20 , respectively. These values significantly exceeded the HER catalysis of a bare/unmodified SPE, which had a HER onset and Tafel slope value of -459 mV (vs. RHE) and 118 mV dec-1, respectively. Clearly, indicating a strong electrocatalytic response from the 2D-WS2-SPEs. An investigation of the signal stability of the 2D-WS2-SPEs was conducted by performing 1000 repeat cyclic voltammograms (CVs) using a 2D-WS2-SPE10% as a representative example. The 2D-WS2-SPE10% displayed remarkable stability with no variance in the HER onset potential of ca. -268 mV (vs. RHE) and a 44.4% increase in the achievable current over the duration of the 1000 CVs. The technique utilized to fabricate these 2D-WS2-SPEs can be implemented for a plethora of different materials in order to produce large numbers of uniform and highly reproducible electrodes with bespoke electrochemical signal outputs.